TI E2E support forums
TI E2E support forums
  • User
  • Site
  • Search
  • User
  • E2E™ design support >
  • Forums
    • Amplifiers
    • API solutions
    • Audio
    • Clock & timing
    • Data converters
    • DLP® products
    • Interface
    • Isolation
    • Logic
    • Microcontrollers
    • Motor drivers
    • Power management
    • Processors
    • RF & microwave
    • Sensors
    • Site support
    • Switches & multiplexers
    • Tools
    • Wireless connectivity
    • Archived forums
    • Archived groups
  • Technical articles
  • TI training
    • Tech days
    • Online training
    • Live events
    • Power Supply Design Seminar
  • Getting started
  • 简体中文
  • More
  • Cancel


Search tips
Showing 373 results View by: Thread Post Sort by
    Answered
  • UCD90320: UCD90320:Remote upgrade

    Elsa Eldhose
    Elsa Eldhose
    Resolved
    Part Number: UCD90320 Hi, We are trying to remote upgrade the UCD90320 firmware through PMBUS script exported from the Fusion Digital Tool. The observations are as follows,The programming get's completed without any issue and the new firmware comes into…
    • Resolved
    • 1 month ago
    • Power management
    • Power management forum
  • UCD90320: UCD90320

    Kevin Cho
    Kevin Cho
    TI Thinks Resolved
    Part Number: UCD90320 Tool/software: Hi Sir, I would like to configure the power-off sequence such that EN_RTVDD_0P77_MAC0 is turned off once AC_OK is pulled low. However, based on waveform measurements, it appears that this setting is not functioning…
    • 4 months ago
    • Power management
    • Power management forum
  • UCD90320: UCD90320

    spoorti oppari
    spoorti oppari
    TI Thinks Resolved
    Part Number: UCD90320 Tool/software: I have connected monitor 12 V to the A7 pin of the UCD90320 and I am controlloing this through the switch. for all the other rails i have given 12V monitor as a dependency..If the 12V monitor is getting all other…
    • 5 months ago
    • Power management
    • Power management forum
  • UCD90320: Fatal Programming Error on UCD90320 – Unable to Upload Configuration

    Humza Khan
    Humza Khan
    Part Number: UCD90320 Hi, We are using the UCD90320 in one of our OAM board designs . During the initial bring-up phase, we were able to successfully install and configure multiple configurations on this device. However, we are now facing an issue…
    • 1 month ago
    • Power management
    • Power management forum
  • Answered
  • UCD90320: UCD90320 DataFlash program NormalL/M (LSB or MSB first)

    Balaji R G
    Balaji R G
    Resolved
    Part Number: UCD90320 Tool/software: During the write phase, each chunk of data is written either LSB first (L designation) or MSB first (M designmation). USC90320 follows which designation ?
    • Resolved
    • 2 months ago
    • Power management
    • Power management forum
  • Answered
  • UCD90320: Issue with HEX File During UCD90320 (PMON) Onboard Programming

    Akhil Tammana
    Akhil Tammana
    Resolved
    Part Number: UCD90320 Tool/software: We've encountered inconsistencies while programming the UCD90320 (PMON) using the PMON dongle at our debug bench. We tested multiple file formats with the following results: .tifsp file – Programming successful;…
    • Resolved
    • 3 months ago
    • Power management
    • Power management forum
  • UCD90320: UCD90320 GPIO Current source / sink maximum capacity

    arulmani v
    arulmani v
    TI Thinks Resolved
    Part Number: UCD90320 Tool/software: How much maximum current can be sourced from one GPIO?, I wants to drive 4 LED's directly from the UCD GPIO, Is this fine?
    • 5 months ago
    • Power management
    • Power management forum
  • Answered
  • UCD90320: PMBus address for the UCD90320

    hanbo chen
    hanbo chen
    Resolved
    Part Number: UCD90320 Tool/software: What do you recommend setting the PMBus address for the UCD90320 to? Can I set it to 119d (decimal)?
    • Resolved
    • 7 months ago
    • Power management
    • Power management forum
  • Answered
  • UCD90320: UCD90320 Design Review

    Fawad Munawar
    Fawad Munawar
    Resolved
    Part Number: UCD90320 Tool/software: T50_OAM_UCD_90320_Review.pdf Hi, We are utilizing the UCD90320 as a power sequencer in one of our Open Accelerator Module (OAM) designs. The sequencer plays a critical role in ensuring the successful power-up of…
    • Resolved
    • 10 months ago
    • Power management
    • Power management forum
  • Answered
  • UCD90320: USB2GPIO

    Hailiang Zhang
    Hailiang Zhang
    Resolved
    Part Number: UCD90320 Tool/software: Hi Expert, My customer found that they couldn't program the UCD90320 using the 2006 USB interface adapter, but they were able to do so with the 2022 USB interface adapter. 1. Can we use the 2006 USB interface adapter…
    • Resolved
    • 2 months ago
    • Power management
    • Power management forum
>

Didn't find what you are looking for? Post a new question.

  • Ask a new question