Search tips
Showing 255 results View by: Thread Post Sort by

  • UCD90320: Can commands greater than 32 bytes be accessed in 32 byte blocks

    TI Thinks Resolved
    Part Number: UCD90320 We have an SMBus controller that's limited to 32 bytes for reads and writes operations. The uc90320 presents a challenge since it has registers(commands) that we need to read and write that are greter than 32 bytes. Is it possible…

  • UCD90320: Fault check

    TI Thinks Resolved
    Part Number: UCD90320 Hi Yihe: As following diagram shows, there's TON_MAX_Fault on Rail #8. On Fault Shutdown Slaves section, I chose almost of power rails, but I found some power rails is still working. - Is this a normal status? UCD90320U_A1 fault_20230208…
    • Answered

  • UCD90320: IMON of TPS259824 connected to AMON pin

    Resolved
    Part Number: UCD90320 Hi Yihe : We want to use IMON of TPS259824 and connect it to AMON of UCD90320 to monitor current consumption. Since IMON is a current output pin of TPS259824, so I need to check some items with you. - 1. Does RADC means resistance of…
    • Resolved

  • UCD90320: READ_TEMPERATURE_1

    TI Thinks Resolved
    Part Number: UCD90320 Hi, Good Day. I have a customer who is working with UCD90320. Please see below his query for your reference. Thank you very much. READ_TEMPERATURE_1 register is a 16-bit register, what do I do with the value of the computer temperature…
    • Answered

  • UCD90320: Temperature check for UCD90320

    Resolved
    Part Number: UCD90320 Hi Yihe: 1. Is there any setting I can change for resolution of temperature shows on monitor window to 0.1C or even 0.01C? 2. Temperature shows on the right window before but somehow it's gone now. How can I show it again?
    • Resolved

  • UCD90320: shutdown sequence not follow configuration

    Part Number: UCD90320 Dear expert, I set rail#25 shutdown dependent on rail#9. But rail#25 always be shutdown before rail#9. I have check enable signal and make sure #25 always be turn down before #9. Which means rail be turned down by UCD90320. May I learn…

  • UCD90320: UCD90320 fusion design tool question

    TI Thinks Resolved
    Part Number: UCD90320 Other Parts Discussed in Thread: INA210 , TMP236 , Hi there In fusion design tool, can you tell me what does each scaling function do? For example Vout Scal Mon, Vout Cal mon, Iout Cal mon, Iout Cal gain And how do I know what value…

  • UCD90320: Synchronisation issues with UCD90320 in Fusion Designer

    TI Thinks Resolved
    Part Number: UCD90320 Hello, I'm trying to configure some LGPO pins on the UCD90320. Sometimes the software gets into a state where any changes I make to the logic don't take effect in the device once I "Write to hardware" and "Store RAM to FLASH"…
    • Answered

  • UCD90320: Behavior check for UCD90320

    Resolved
    Part Number: UCD90320 Hi ; 1. Is it OK for V33A,V33D and Reset ramp up together? - 2. When I'm doing validation report, I found it take UCD90320 around 55ms from Reset is released to Enable, GPO and some LGPO to act. Is this a normal value? - If not…
    • Resolved
    • Answered

  • RE: UCD90320: UCD90320 debug with multimeter

    Resolved
    Hello If .csv file was generated by data flash script for UCD90320, and the file is on my hand. Can it be converted under offline mode? 1. data flash csv file --> former (can only be converted on a live device). 2. pmbus command script csv file. -…

Didn't find what you are looking for? Post a new question.