• 

  Andreas K

  • 17 days ago
  • Wi-Fi
  • Wi-Fi forum

  WL1801MOD: Certification outside of EU

  TI Thinks Resolved

  Part Number: WL1801MOD Hi Team, customer would like to certify the product outside of EU. Is it possible to get a test report and measurements according to RED 2014/53/EU? Which additional measurements will they have to perform? Regards And...
• 

  Simon Werner1

  • 3 days ago
  • Wi-Fi
  • Wi-Fi forum

  RE: WL1801MOD: Many interrupts triggered

  Hi Saurabh N , thank you for your response. We have checked the h/w irq setting and it all looks good. We also tried changing the interrupt from level (4) to rising edge (1) and that caused the chip to not come up. Attached is the hostapd log. Also...
• 

  Carl Omundsen

  • 1 month ago
  • Wi-Fi
  • Wi-Fi forum

  WL1801MOD: Low tx power levels

  Part Number: WL1801MOD Using the WL1801MOD and attempting to get full control of the transmit power levels. calibrator get drv_info wlan0 Driver wl18xx_driver version 4.19.0-Vesper FW version Rev 8.9.0.0.81 Bus info wl18xx.0.auto HW version 0x6030111...
• 

  Saurabh N

  • 21 days ago
  • Wi-Fi
  • Wi-Fi forum

  RE: WL1801MOD: Support for 4.14 kernel driver patching scripts [beaglebone black]

  Hi , " wl1271_sdio mmc1:0001:2: sdio write failed (-110) " could be related to SDIO failure. You may try reducing SDIO/MMC bus clock speed to a low value ex: 1MHz in dts file and re-test . Also probe wlan_en and wlan_irq to confirm wlan_en...
• 

  Michael Reymond

  • 1 month ago
  • Wi-Fi
  • Wi-Fi forum

  RE: WL1801MOD: FW loading failed

  Hi Jiri, Is the one problematic device running with the same hardware as with the other devices that boot up without issues? Knowing what differences there are would be useful for debug. For configuration of dual role on the WL1801 you can take...
• 

  Kazuhiko Hirano

  • 4 months ago
  • Wi-Fi
  • Wi-Fi forum

  WL1801MOD: Ripple spec at VBAT

  • Resolved

  Part Number: WL1801MOD Hello, Any ripple requirements to be followed at VBAT to keep good RF
• 

  Rizwan Murji

  • 5 months ago
  • Wi-Fi
  • Wi-Fi forum

  RE: WL1801MOD: Anatel Cert renewal for WL1801MOD

  Hi David, Since Anatel is required to be renewed every 2 years, it is highly dependent on the demand of the customer. You can check back with us in a few months on this. This was done for a particular customer of ours and thus will be someone dependent...
• 

  Stavros Vagionitis

  • 7 months ago
  • Wi-Fi
  • Wi-Fi forum

  WL1801MOD: disconnects and does not reconnect immediately to APs which have the same SSID but different frequency (2.4GHz or 5GHz) and BSSID

  • Resolved

  Part Number: WL1801MOD Hi there, I have the following issue: I am connecting to the corporate
• 

  Darcy Williams

  • 11 months ago
  • Wi-Fi
  • Wi-Fi forum

  WL1801MOD: Unable to achieve conducted power output greater than 1.8dBm

  • Resolved

  Part Number: WL1801MOD Hopefully I can provide enough info on my first try with this inquiry
• 

  Koichiro Tashiro

  • 9 months ago
  • Wi-Fi
  • Wi-Fi forum

  WL1801MOD: Clock Synchronization

  TI Thinks Resolved

  Part Number: WL1801MOD Hi, My customer is trying to implement Clock Synchronization described in below Wiki. http://processors.wiki.ti.com/index.php/WL18xx_Clock_Synchronisation_with_NTP_in_SDK3 In this wiki, WL1835 which is on the BeagleBoneGreen is...

Didn't find what you are looking for? Post a new question.

• Ask a new question