Search tips
Showing 200 results View by: Thread Post Sort by

  • CC1310: WMBUS-CC13X0

    TI Thinks Resolved
    Part Number: CC1310 Hi team, The customer is designing a WM-Bus module based on CC1310 and WMBUS-CC13X0. The module will communicate with the customer's smart meter over UART. The WM-Bus module collects data from nearby WM-Bus gas and water meters…

  • RE: CC1310: Problem in setting the transmission time of wmbus, OMS, C1 modes

    Hi team, does wmbus have an API that configures the sending time interval, such as when to what time it can be sent, or do I need to manually turn it on and off myself.

  • LAUNCHXL-CC1310: CC1310 with WMBUS - Help with starting a new project

    Part Number: LAUNCHXL-CC1310 Other Parts Discussed in Thread: WMBUS , CC1310 Hello forum I want to create a wmbus application that can handle t1 and c1 modes on the cc1310 launchpad. I Have seen the stackforce implementation of the wmbus stack but i have…

  • RE: LAUNCHXL-CC1350-4: WMBUS S2/C2 Collector do not response

    Hi As I do not have a wmbus sniffer, I asked SF for help and below are their response: "So, we have downloaded the wmbus stacks from https://www.ti.com/tool/WMBUS . I see that the version is v.2.0.0. Then, we run the following configurations on two…
    • Answered

  • CC1310: Can EasyLink receive wMBus messages in C (and/or T) mode?

    Resolved
    Part Number: CC1310 Other Parts Discussed in Thread: WMBUS , I'm working on a project based on EasyLinkEcho (RX/TX) example (SimpleLink CC13x0 SDK v4.20.02.07 in CCS 12.0.0.00009). In parallel I'm using wMBus stack (wmbus-cc13xx-rtos-2.0.0 in CCS 8.1…
    • Resolved
    • Answered

  • LP-CC1312R7: wmbus MTO rx not working properly while wmbus OTM rx is working with the same payload, sync word and CRC

    Resolved
    Part Number: LP-CC1312R7 Other Parts Discussed in Thread: WMBUS , , CC1312R7 , CC1101 , CC1200 Hi, I have successfully performed rx measurements on Wmbus OTM sending packets either between 2 boards or between an ESG 4438C signal generator and a LP-CC1312R7…
    • Resolved
    • Answered

  • CC1310: Removing Extended Link Layer from WMBus Messages

    Resolved
    Part Number: CC1310 Other Parts Discussed in Thread: WMBUS Hello, I am having trouble talking to a third party device. I believe one possible cause is that the device may only support OMS v3.0.1. I notice that the WMBus stack adds the extended link layer…
    • Resolved

  • CC1310: WMBus Postamble is 3 out of 6 Encoded

    Part Number: CC1310 Other Parts Discussed in Thread: WMBUS Hello, I am debugging communication between the CC1310 Launchpad and a third party device. I have been running the APL Meter T1 example, and have exported the MCE_GPO0 signal to an external pin…

  • CC1312R: CC1312 WMBUS 0x3805 PROP_ERROR_RXOVF

    Part Number: CC1312R Other Parts Discussed in Thread: WMBUS Hi Champs, Customer evaluates our WMBUS offer and has the following challenges: "When I use partial mode for WMBUS (I finally used the non repeat mode RX, I have one RX cmd chained to a loop)…

  • CC1310: wMBus Patch question to Postamble

    TI Thinks Resolved
    Part Number: CC1310 Other Parts Discussed in Thread: WMBUS Hi, in a post around 5 years ago it is written that the wMBus patch also sends Postamble if using the patch as described in swra522 . Related qustion: https://e2e.ti.com/support/wireless-connectivity…

Didn't find what you are looking for? Post a new question.