Search tips
Showing 100 results View by: Thread Post Sort by

  • BQ25798EVM: [3D Request] Missing Information: BQ25798EVM

    TI Thinks Resolved
    Part Number: BQ25798EVM Other Parts Discussed in Thread: BQ25798 Tool/software: Dear Texas Instruments Team, Good day. This is Louie from SnapMagic Search. We create PCB footprints, schematic symbols, and 3D models for electronic components. One…

  • BQ25798EVM: BQ25798EVM

    TI Thinks Resolved
    Part Number: BQ25798EVM Tool/software: I am looking at the BQ25798EVM manual. If I want to perform a simulation according to this manual, should I connect an electronic load in constant voltage mode to the J5 terminal?

  • BQ25798EVM: SYS Pin output

    TI Thinks Resolved
    Part Number: BQ25798EVM Other Parts Discussed in Thread: BQ25798 Hi I'm Hari. We are using a battery charger with part number BQ25798 in a project. For testing the working, we had bought the EVM of the same part number. In the datasheet, a table is…
    • Answered

  • BQ25798EVM: Request for config file

    Resolved
    Part Number: BQ25798EVM Other Parts Discussed in Thread: BQSTUDIO , BQ25798 Hello Team, We are planning to use the BQ25798EVM board for our development. While using BQStudio , we are unable to find the corresponding board configuration file. Could you…
    • Resolved
    • Answered

  • BQ25798EVM: Regulating Output Voltage (VSYS ) for BQ25798

    Resolved
    Part Number: BQ25798EVM Other Parts Discussed in Thread: BQ25798 Hi Team, In our design, VSYS is used to power an external PMIC (PCA9450C), which typically expects a stable 5 V input. Our battery configuration has 2-cell which give total 8V output …
    • Resolved

  • BQ25798EVM: VBAT_OVP triggered after charging is enabled

    Part Number: BQ25798EVM Other Parts Discussed in Thread: BQ25798 Hi, I'm trying to test out the BQ25798EVM for charging my LiFePO4 1S battery (Charging Voltage 3.6). Most of the time when I enable charging, it would directly raises the VBAT_OVP flag…
    • Answered

  • BQ25798EVM: QON pin not working in ship mode

    Resolved
    Part Number: BQ25798EVM Other Parts Discussed in Thread: BQ25798 Hello Team I am currently using BQ25798EVM board. I am trying to test the power-control functions , the QON pin behavior, Shutdown Mode, Ship Mode, and System Power Reset. Here is the…
    • Resolved

  • BQ25798EVM: 2s battery controlled by BQ25798

    TI Thinks Resolved
    Part Number: BQ25798EVM Other Parts Discussed in Thread: BQ40Z50 Tool/software: Hi, Can you please share what battery of type 2s (2 cells) Ti tested the chip. The battery should be smart battery with TS pin and i2C/SM bus . I intend to purchase…
    • Answered

  • BQ25798EVM: VSYS OVP FLAG and VBAT OVP FLAG

    Resolved
    Part Number: BQ25798EVM Other Parts Discussed in Thread: BQ25798 Tool/software: Hi, I am using the BQ25798EVM with this setup: I configured it with 1 Cell but I am having the VBAT OVP FLAG tough ADC BAT measure is 3,853V. I can't figure out why…
    • Resolved
    • Answered

  • BQ25798EVM: Mistake on 2.4.1 Initial Settings

    Resolved
    Part Number: BQ25798EVM Other Parts Discussed in Thread: BQ25792EVM , BQSTUDIO , BQ25790EVM , BQ25798 Tool/software: Hi, On section 2.4 Test Procedure 2.4.1 Initial Settings Use the following steps to enable the EVM test setup. 1. Make sure Section…
    • Resolved

Didn't find what you are looking for? Post a new question.