Search tips
Showing 839 results View by: Thread Post Sort by

  • CC1352P7: Query Regarding CC1352P7 Operation on 1.8V Rail

    TI Thinks Resolved
    Part Number: CC1352P7 Hello Team, We are planning to use the CC1352P7 Sub-1 GHz module in our upcoming products. In our design, we intend to operate the CC1352P7 module only on a 1.8V supply rail. We have planned the below power connections: VDDS…

  • CC1352P7: Feasibility of Running Sub-1 GHz + Thread + Zigbee Concurrently on CC1352P7

    Part Number: CC1352P7 Other Parts Discussed in Thread: CC1354P10 Hello TI Community, We are evaluating the CC1352P7 for one of our products and would like to understand whether it is feasible to run the following wireless protocols concurrently within…
    • Answered

  • CC1352P7: The question about the flash power-fail protection mechanism of the CC1352P7 microcontroller

    Resolved
    Part Number: CC1352P7 Other Parts Discussed in Thread: UNIFLASH , CC1352P , CCSTUDIO hello, I need to reproduce an issue where the microcontroller restarts when reading a specific flash area after a power failure occurs during flash writing or erasing…
    • Resolved

  • CC1352P7: CC1352P7 MCUBoot overwrite + external flash update not booting new firmware (SDK 8.31.x.x)

    Part Number: CC1352P7 Other Parts Discussed in Thread: SYSCONFIG , UNIFLASH Dear TI Support Team, I am working on firmware update using MCUBoot on CC1352P7 and would appreciate clarification and guidance, as I am currently stuck at runtime behavior…

  • CC1352P7: CC1352P7-1: Developing a Standalone UART-to-Wi-SUN Bridge without an External Host

    TI Thinks Resolved
    Part Number: CC1352P7 Other Parts Discussed in Thread: SYSCONFIG , UNIFLASH Description: I am using two LP_CC1352P7-1 LaunchPads to evaluate a Wi-SUN FAN mesh network. My goal is to create a standalone "Sensor Node" that reads data from a sensor via…

  • LP-CC1352P7: CC1352P7: 4-GFSK Reception Degradation After few Minutes

    Part Number: LP-CC1352P7 Other Parts Discussed in Thread: CC1352P7 Tool/software: Device: CC1352P7 (LP_CC1352P7_1) SDK: SimpleLink CC13xx/CC26xx SDK 8.30.01.01 IDE: Code Composer Studio Configuration: Modulation: 4-GFSK ( formatConf.fecMode = 0x09…

  • CC1352P7: CC1352P7

    Part Number: CC1352P7 Tool/software: Hello, I'm using CC1352P7 as a route node and running ns_node file to connect with WI SUN border router which is a ERF32 board connected with raspberry Pi. After flashing the ns_node code the serial monitor message…

  • CC1352P7: SPI communication between CC1352P7-1 (Wi-SUN) and ESP32 — data not transmitting properly over Wi-SUN

    TI Thinks Resolved
    Part Number: CC1352P7 Other Parts Discussed in Thread: SYSCONFIG , , LPSTK-CC1352R Hi, I am working on a project using the CC1352P7-1 LaunchPad running the ns_node Wi-SUN stack. My goal is to use an ESP module as an external MCU that sends data to the…

  • CC1352P7: How to configure Mode 2?

    Part Number: CC1352P7 Other Parts Discussed in Thread: CC1352P Hi, In the following configuration, the sending spectrum can not be seen; modify .formatConf.nSwBits from 0x40 to 0x20, and CC1352P receiver can not trigger RF_Callback function. // CMD_PROP_RADIO_DIV_SETUP_PA…

  • CC1352P7: Higher RX/TX current consumption than datasheet at 3.3V - CC1352P7-1 868Mhz @ 300 kbaud

    Part Number: CC1352P7 Tool/software: I'm observing significantly higher RX and TX current consumption (~12 mA) compared to the CC1352P7 datasheet values (5.4 mA RX, 8.0 mA TX) during normal operation. I'm trying to understand the root cause and how to…

Didn't find what you are looking for? Post a new question.