• 

  Simon J

  • over 2 years ago
  • Zigbee & Thread
  • Zigbee & Thread forum

  RE: CC2650EM-MURBAL-RD: width for printed circuit board line to antenna

  Hi Antrio, The trace from the balun to antenna on the EM is not to to be considered as a transmission line since the length is shorter than 1/10 of the wavelength. If your design requires a transmission line between the antenna and balun, you'll...
• 

  Dhanraj

  • over 2 years ago
  • Zigbee & Thread
  • Zigbee & Thread forum

  CC2650EM-MURBAL-RD: what is the slandered procedure to conduct the Range Test for zigbee module ?

  Part Number: CC2650EM-MURBAL-RD Hello, what is the slandered procedure to conduct the Range Test for zigbee module? what parameter should be considered for the test and what should be the threshold value to conclude good communication/poor communication...
• 

  Dhanraj

  • over 2 years ago
  • Zigbee & Thread
  • Zigbee & Thread forum

  CC2650EM-MURBAL-RD: Availability issue with balun used in the reference design.

  Part Number: CC2650EM-MURBAL-RD Hello, I am using cc2650f128RHB package for zigbee. There is availability issue with the balun used in this reference design - 1) kindly suggest pin compatible alternative balun solution. 2) what is the differential...
• 

  Rahul Gusai

  • 2 months ago
  • Other wireless
  • Other wireless technologies forum

  CC2650EM-5XD-RD: How to measure the battery level

  TI Thinks Resolved

  Part Number: CC2650EM-5XD-RD Hello, I have a custom board based on the CC2650 which has to be powered by a coin cell battery. What is the best way to measure the battery level for this in firmware? Thanks Rahul Gusai
• 

  Aditya R

  • 8 months ago
  • Bluetooth®
  • Bluetooth® forum

  CCS/CC2650EM-5XD-RD: cc2650EM-5xd_rd

  TI Thinks Resolved

  Part Number: CC2650EM-5XD-RD Tool/software: Code Composer Studio Hi, I'm using cc2650moda booster pack and I want to run simple peripheral program. First I built and debug stack ccs file then app ccs file. There is no error but I'm not getting...
• 

  Rahul Gusai

  • 3 months ago
  • Other wireless
  • Other wireless technologies forum

  CC2650EM-5XD-RD: Can't communicate with CC2510 radio.

  Part Number: CC2650EM-5XD-RD Hello, I am trying to communicate with CC2510 using proprietary RF mode. I was successful in doing this using CC2650-LAUNCHPAD with the following settings in the smartrf_settings.c. So, I tried the same on our custom board...
• 

  Franz Schellhase

  • 4 months ago
  • Bluetooth®
  • Bluetooth® forum

  CC2650EM-7ID-RD: Set transmission power

  Part Number: CC2650EM-7ID-RD Hi Team, Can you help my customer with the following request? I have configured a setup with an evaluation board SmartRF06 with a CC2650EM-71D rev. 1.2. The DTM commands were sent via the BTool. The measurements resulted...
• 

  Serdar Köse

  • over 4 years ago
  • Zigbee & Thread
  • Zigbee & Thread forum

  Impedance matching of cc2650em-murbal-rd

  I draw the schematics on ADS: trace widths are 0.15 mm and lengths are about 1.1 mm from CC2650 to the balanced ports; trace width is 0.6 mm and length is about 12.1 mm from balanced port of the balun to the SMA connector. However, S 1,1 plot...
• 

  Eirik V

  • over 4 years ago
  • Bluetooth®
  • Bluetooth® forum

  RE: Use of Balun in Sensor tag

  Hello Surya Teja, I think the reason was that there was no available at the time of design for the ST2.0. See the CC2650EM-MurBal Reference Design: www.ti.com/.../cc2650em-murbal-rd For HW design guide, also look at the "Design Resources"...
• 

  Rahul Gusai

  • 2 months ago
  • Zigbee & Thread
  • Zigbee & Thread forum

  CC2650EM-5XD-RD: Not able to power down the radio core

  Part Number: CC2650EM-5XD-RD Hi, I am writing the firmware for a custom board based on CC2650. The device has to remain in StandBy mode only except the times when it has to transmit or receive some data. Transmitting logic has already been implemented...

Didn't find what you are looking for? Post a new question.

• Ask a new question