• 

  Anish Hemachandran

  • 8 months ago
  • Simulation, hardware & system design tools
  • Simulation, hardware & system design tools forum

  TIDA-00361: .sln file missing when building source file with cmake

  TI Thinks Resolved

  Part Number: TIDA-00361 Hi , When I follow the pdf http://www.ti.com/lit/ug/dlpu042/dlpu042.pdf to make source files with cmake, I get all the .exe files built properly . But there is no .sln file to open with in c++., to modify these files. Is...
• 

  Fizix

  • 8 months ago
  • Simulation, hardware & system design tools
  • Simulation, hardware & system design tools forum

  RE: TIDA-00361: Is there a drawing for the camera stand?

  Hello Ugnius, This stand was made in our internal shop and regrettably does not have a drawing. It should be simple to manufacture by hand in a shop (as we did for the one shown). Make it so the angle the camera is pointing (up/down) with a little...
• 

  Anish Hemachandran

  • 2 months ago
  • DLP® products
  • DLP® products forum

  DLP3000 Lightcrafter Kit and setup for scanning project

  • Resolved

  Part Number: DLP3000 Hi , Could you please provide me the exact details for setup used in the point cloud generation setup in : I do have my own setup and have experimented with the setup and paramters quite a bit now. I believe my problem is for the distance the projector scanning lines are in focus...
• 

  Shravani Erukala

  • 3 months ago
  • DLP® products
  • DLP® products forum

  camera for dlp3000 light crafter evm kit

  TI Thinks Resolved

  Part Number: DLP3000 Hi, I have this kit DLP3000 light crafter. To use the software of it, initially I worked with webcam but have some issues. Then decided to buy point grey camera mentioned in BOM of TIDA00361( ). I have been informed that this camera...
• 

  Paul Goedeke

  • over 1 year ago
  • DLP® products
  • DLP® products forum

  RE: Can't compile LightCrafter SDK nor run the given executable

  Hi Pablo, Can you attach a picture of the 0xC0150002 error? Before we get into diagnosing the compiling issue, I'd really like to see the executable run. Can you try uninstalling and reinstalling all the components for TIDA-00361 and see if the...
• 

  Philippe Dollo

  • over 1 year ago
  • DLP® products
  • DLP® products forum

  RE: DLPC300: About RESET of DLPC300

  GK, What is the purpose of this design? I recommend following the DLPC300 reference design to prevent these signals from interacting in an unintended way: www.ti.com/.../tida-00361 Best Regards, Philippe Dollo
• 

  Manouk Abkarian

  • over 3 years ago
  • DLP® products
  • DLP® products forum

  TIDA-00361

  • Resolved

  DLP Technology" that can be found at this link: www.ti.com/.../ TIDA - 00361 The reference design
• 

  Pablo Cottens

  • over 1 year ago
  • DLP® products
  • DLP® products forum

  DLP3000: Problems calibrating DLP3000 TIDA-00361

  Part Number: DLP3000 Hello, as stated I'm having problems calibrating my board. I am following TIDA-00361 with a Microsoft camera I do as the document says, I generate a new calibration board by pressing option 1, after that I do a camera calibration...
• 

  Armando Leopoldo Keller

  • over 1 year ago
  • DLP® products
  • DLP® products forum

  DLPLIGHTCRAFTER: Error with tida-00361 and MSP430 Firmware version

  • Resolved

  Part Number: DLPLIGHTCRAFTER Helo, we are trying to follow the tida - 00361 design reference for 3D
• 

  Paul Goedeke

  • over 2 years ago
  • DLP® products
  • DLP® products forum

  RE: The image captured by FL3-U3-88S2C-C Camera is half white and half dark when I perform calibration, why?

  Clifford, Two things: 1. Can you lower your camera exposure but leave the projector exposure? Try a scan with these settings. PG_FLYCAP_PARAMETERS_SHUTTER_EXPOSURE_MS = 30 PG_FLYCAP_PARAMETERS_FRAME_RATE_HZ = 15. 2. When you do a scan, in the...

Didn't find what you are looking for? Post a new question.

• Ask a new question