• 

  Taylor Vogt

  • 1 month ago
  • Power management
  • Power management forum

  RE: BQ76PL536A: Application solution of single voltage acquisition

  Hi Elsa, Here is a reference design using this device: https://www.ti.com/tool/TIDA-00821 However, this is an older device, I recommend looking into bq79606a or bq79616 product folders as they come with higher robustness, features, etc. Regards...
• 

  Taylor Vogt

  • 7 months ago
  • Power management
  • Power management forum

  RE: BQ76PL536A: Full Schematic Request

  Hi Henar, What exactly are you looking for? We have a typical application schematic in section 8.2 of the datasheet and also you can download an example here: https://www.ti.com/tool/TIDA-00821 . Regards, Taylor
• 

  John Griffin1

  • 10 months ago
  • Power management
  • Power management forum

  RE: UCC2808-2: Gate drive resistor values vs absolute maximum ratings?

  Hello Brian, The -0.5A and 1.0A limits are continuous current limits and if you use the UCC2808-2 to drive a pair of FETs the current is pulsed due to the capacitive nature of the gate to source connection. This means the average drive current is very...
• 

  shaury anand

  • over 3 years ago
  • Simulation, hardware & system design tools
  • Simulation, hardware & system design tools forum

  RE: TIDA-00827: Can't find the schematic of TIDA-00827 EVM

  I am looking for schematic of TIDA-00821. I mentioned wrong TIDA number earlier.
• 

  Roger Hwang

  • over 2 years ago
  • Power management
  • Power management forum

  RE: BQ76PL536EVM-3: Schematic?

  www.ti.com/.../TIDA-00821 go check this site.
• 

  Roger Hwang

  • over 4 years ago
  • Power management
  • Power management forum

  RE: BQ76PL536-Q1 MISO high when CS asserted (low)

  Marteen, 1. How did you connect HSEL for slave devices? 2. What is connect to GPIO? 3. I need to see your schematic before I can commnet. Are you using TI GUI or your own F/W? 4. It's okay to use PS. Take a look TIDA-00821. You will see how...
• 

  Roger Hwang

  • over 4 years ago
  • Power management
  • Power management forum

  RE: BQ76PL356A SPI communication

  Hi Zihui, Please check HSEL pin. Go check out TIDA00821 design reference from TI product Make sure HSEL is connected to LDOD for slave ICs.
• 

  Roger Hwang

  • over 2 years ago
  • Power management
  • Power management forum

  RE: BQ76PL536A-Q1: Digital isolator supply

  REG50 shuts down in sleepmode. It means that you can not WAKE up the IC once device goes into sleep mode. Digital isolator is to isolate high and low voltages. level shifter is not the way to use for isolation. Go to this link and you can find...
• 

  Roger Hwang

  • over 4 years ago
  • Power management
  • Power management forum

  RE: BQ76PL356. ISOLATED POWER SUPPLY?????

  HI MS, I don't have reference schematic for external circuit. Every customer that I know uses cell to power the pl536A. Let me answer your questions 1st. 1. No, you don't change the RC filter. You will have same RC filter. 2. I don't...
• 

  Roger Hwang

  • over 4 years ago
  • Power management
  • Power management forum

  RE: bq76pl536 evm board schematics

  You can find the all the information here. Take a look. http://www.ti.com/tool/TIDA-00821?keyMatch=tida-00821&tisearch=Search-EN-Everything

Didn't find what you are looking for? Post a new question.

• Ask a new question