Search tips
Showing 212 results View by: Thread Post Sort by
    Answered

  • TMS320F28384D: I tried creating a new projected in CCS Version: 20.2.0.12__1.8.0 using the Cortex M4 core examle. Unable to do so.

    Resolved
    Part Number: TMS320F28384D Other Parts Discussed in Thread: TMS320F28388D Tool/software: Received error "No TI compilers supporting "TMS320F28388D" {Cortex M] are currently installed Apparently the new 20.2.0 tools only directly support the C2000 Clang…
    • Resolved

  • TMS320F28384D: Does DSP built-in voltage supervisor to monitor VDDIO and VDD?

    TI Thinks Resolved
    Part Number: TMS320F28384D Tool/software: Hi champs, My customer would like to know if F2838x devices support any hardware to monitor VDDIO and VDD voltages, to determine the over or under voltages situation happens? Please advise your comments…

  • TMS320F28384D: Does NMI reset the CPU or just drive ERRORSTS Pin low?

    TI Thinks Resolved
    Part Number: TMS320F28384D Tool/software: Does the NMI in TMS320F28384D reset the CPU or simply drive the ERRORSTS Pin low? If the CPU is not reset by the NMI, then it would be advisable to utilize the ERRORSTS Pin for resetting the CPU.
    • Answered

  • TMS320F28384D: Delay time for VDD, VDDIO, and XRSn

    Resolved
    Part Number: TMS320F28384D Hi All In the datasheet, TYP values are given for VXRSn-Pu-DERAY, VXRSn-PD-DERAY and VDDIO-MON-TOT-DERAY. What is the MIN and MAX of these values? Best Regards, Ito
    • Resolved

  • TMS320F28384D: Optimizing Data Transfer Between CPU1 and CM for Efficient Ethernet Communication

    Part Number: TMS320F28384D Tool/software: Hi, We are using this Part.No TMS320F28384D. We are using CPU1 for the power control algorithm and CM for Ethernet communication. We would like to have some advice regarding the transfer of data between CPU1…

  • TMS320F28384D: GPIO Pin pulled up at power up leading to short Circuit

    Part Number: TMS320F28384D Tool/software: Hello, I am currently using the above DSP to control a half bridge board. My problem is that I have found that both mosfet gates of my half bridge are driven at the same time during power up of my DSP board and…
    • Answered

  • TMS320F28384D: CPU does not start up according to datasheet

    Resolved
    Part Number: TMS320F28384D Hi All, What is the cause that CPU does not start up under the following conditions? ・After 3.3V starts up , 1.2V starts up about 200ms later. When external reset is input about 530ms after that, the CPU does not start…
    • Resolved
    • Answered

  • TMS320F28384D: Is it possible to use an internal regulator ?

    Resolved
    Part Number: TMS320F28384D Hi All, Is it possible to use an internal regulator with the TMS320F28384D? Can it be started with a single 3.3V power supply? Best Regsrds, Ito
    • Resolved

  • TMS320F28384D: Requirement of 7 UART Channels

    Part Number: TMS320F28384D Dear Madam/Sir, I have a requirement of 7 UART channels in my overall application. As per the datasheet the above chip supports 4 SCI channels ,one CM-UART For debugging purpose, generally we use one of the SCI- UART with…

  • TMS320F28384D: File Loader: Verification failed

    Part Number: TMS320F28384D Hello, I had a problem, I managed to solve it but I didn't understand why. I have a working program that runs on several boards and I always manage to flash this program correctly. I've received new boards with the…

Didn't find what you are looking for? Post a new question.