Search tips
Showing 315 results View by: Thread Post Sort by
    Answered

  • TPS2595: [TPS259541] The part's programmed current limit does not trigger

    Resolved
    Part Number: TPS2595 Tool/software: I'm using this model as an efuse for a 12V input and where the circuit will max out at ~1.5A. Since I'm using a 910Ω resistor elsewhere and ~2A is fine, that's what I stuck in the Rilm position, as you can see in…
    • Resolved
    • Answered

  • TPS2595: eFuse Reverse Diode Spec

    Resolved
    Part Number: TPS2595 Tool/software: I am applying a voltage in the reverse direction through the TPS259570DSG chip so the current is flowing via the reverse diode from the OUT port to the IN port. I have tested this successfully at approx. 16V, 2A.…
    • Resolved
    • Answered

  • TPS2595: FLT response for TPS259541

    Resolved
    Part Number: TPS2595 Tool/software: Hello team, My customer is evaluating TPS259541 with TPS2595EVM. When testing current limit function, FLT looks auto-retrying, even if Vout is still 0V. Is this expected? Can you explain why this periodic waveform…
    • Resolved

  • TPS2595: TPS259540 rise time formula

    TI Thinks Resolved
    Part Number: TPS2595 Tool/software: Hi Team do we have any rise time formula can be reference? because I think datasheet only have Slew rate formula. BTW may I know what is the difference between Slew rate and Rise time? BRs Bri…

  • TPS2595: BPS topology – High current consumption when both EN = LOW

    Part Number: TPS2595 Other Parts Discussed in Thread: TPS25948 Tool/software: I'm facing a similar issue to the one reported in the following thread: TPS2595: High shutdown current observed while using the TPS259573 as a BPS. I’m implementing the…

  • TPS2595: how to decide the value of RQODEXT

    TI Thinks Resolved
    Part Number: TPS2595 Tool/software: Hi team Could you tell how to deice the value of RQODEXT? It seems RQODEXT is required accoring to figure 62, however there are no descriptions about how to decide the value of RQODEXT. RQODEXT is different…

  • TPS2595: TPS259541 OVP Didn't Trigger

    Part Number: TPS2595 Tool/software: Hi expert, Customer set the OV threshold to 14V but still didn't trigger OVP until 15V. Would you please have a look and advise what might goes wrong? TPS259573_Design_Calculator_RevA_20241101.xlsm Thanks…

  • TPS2595: The exposed pad

    TI Thinks Resolved
    Part Number: TPS2595 Tool/software: Hi All, I have a question about the TPS259533. Is the PAD connected to GND internally? The NAME is GND, but when I checked the continuity between the GND terminal and the PAD on the IC alone, it was not connected…

  • TPS2595: eFuse for 1.8V rail

    Part Number: TPS2595 Tool/software: Hi Team, Do we have any eFuse solution which supprot 1.8V rail? p2p with TPS2595 is better for me if we have. Regards, Kotaro Yamashita

  • TPS2595: TPS259533 eFuse usage

    TI Thinks Resolved
    Part Number: TPS2595 Other Parts Discussed in Thread: TPS2117 , Tool/software: Hello, I have a 2 DCAP3 buck regulator, one for 3.3v and one for 5v. I hooked their input to TPS2117 power selector IC but this IC is limited to 4 amps while buck regulators…

Didn't find what you are looking for? Post a new question.