Search tips
Showing 140 results View by: Thread Post Sort by

  • TPS61030 Loop gain stable or not

    Hi For a stable system, the slope should be -20db/decade at the gain crossover 0db. The slope is about -30db/decade at the gain crossover 0db. Is it a concern for stability? please see below

  • TPS61030 Bode Plot question

    Other Parts Discussed in Thread: TPS61030 Hi experts, Customer design TPS61030 and Vin=4.6V; Vout=5V. And they measure Bode-plot in below picture. Can you advice is there any concern if there is multi-crossover points when Gain is in 0dB? Can you…
    • Answered

  • Could TPS61030 work in LDO mode?

    Resolved
    Other Parts Discussed in Thread: TPS61030 , TPS61020 , TPS63020 Dear all: If input voltage is 5.25V, output is fixed 5V/2000mA. As I know, TPS6102X can work at LDO mode. But TPS61030 didn't showed ths application note in datasheet. Is TPS61030…
    • Resolved
    • Answered

  • TPS61030/90 EN pin max voltage

    Resolved
    Other Parts Discussed in Thread: TPS61030 Question: Can the EN pin be taken above Vin?
    • Resolved
    • Answered

  • TPS61030 down mode?

    Resolved
    Other Parts Discussed in Thread: TPS63020 , TPS61030 We have need of a switcher that can maintain a voltage of 3.3V when the supply is 2.7V and 3.6V. It also needs to supply 2A peaks to a 3G Cell phone module as well as powering an ARM processor. Since…
    • Answered

  • TPS61030 - use LBI/LBO as PG?

    Resolved
    Is there any reason why LBI could not be used with a divider and wired to VOUT to supply a power-good. I don't need to use it for battery monitoring. I was going to use system 3.3V to pull up LBO.
    • Resolved
    • Answered

  • RE: TLV61070A: Output abnormal

    Resolved
    Hi Travis, Very thanks for your advice. I recieved EOL information from TI that TPS61032 will EOL, do you think TPS61030 is a good replacement solution has less modification? only add two feedback resistors to TPS61030 FB pin to meed 5V output.…

  • TPS610333: Frequency synchronization function concern

    Part Number: TPS610333 Other Parts Discussed in Thread: TPS63070 , TPS61030 , TPS61033 , TPS61178 Hi team I found TPS610333 show "Frequency synchronization" in the public page as below: but didn't find this function in datasheet, so whether TPS610333…
    • Answered

  • TPS61236P: Need boost converter with pass-through for VIN>VOUT

    Resolved
    Part Number: TPS61236P Other Parts Discussed in Thread: TPS61023 , , TPS61030 , TPS63811 I need a boost converter for a 3.7V, 1A load (not switch current!) from a single LiPo cell that we want to run down to 3.0V. We also need this to operate when the…
    • Resolved
    • Answered

  • Designing low power consumption board (3.3V and 5V converters)

    Resolved
    Other Parts Discussed in Thread: TPS61030 , TPS62740 , TLV61220 , TPS61023 , TPS61099 Hello, I want to make board for wireless project. Project will be powered from 2x series LR20 battery (3.2V max). Power consumtion on 3.3V is less than 0.1mA while sleeping…
    • Resolved

Didn't find what you are looking for? Post a new question.