TI E2E support forums
Menu
Search through millions of questions and answers
User
Menu
Search through millions of questions and answers
User
E2E™ support forums
Forums
Amplifiers
Audio
Clock & timing
Data converters
DLP® products
Interface
Isolation
Logic
Microcontrollers
Motor drivers
Power management
Processors
RF & microwave
Sensors
Site support
Switches & multiplexers
Tools
Wireless connectivity
Archived forums
Archived groups
Technical articles
Analog
Automotive
DLP® technology
Embedded processing
Industrial
Power management
Think. Innovate
0
TI training
Tech days
Online training
Live events
Power Supply Design Seminar
Getting started
More
Cancel
简体中文
Search tips
Showing 39 results
View by: Thread
Post
Sort by
Relevance
Oldest to Newest
Newest to Oldest
Chris Schramm
2 months ago
Switches & multiplexers
Switches & multiplexers forum
TMUX1111: Low current power rail switching
Resolved
? An alternate which states "Power Routing" in its d/s could be
TS3A4751
but it has a max of 3.6V and I don't
Randy May
over 1 year ago
Switches & multiplexers
Switches & multiplexers forum
TS3A4751: Power Sequencing Protection
TI Thinks Resolved
Part Number:
TS3A4751
Greetings, I am using a
TS3A4751
PWR analog switch in the following generalized application which optionally turns on/off a 3.3k pull-up on a net. The problem is that I have no control over when 3.3V_Remote turns on relative...
Lawrence He
over 1 year ago
Switches & multiplexers
Switches & multiplexers forum
TS3A4751: TS3A4751 OVP Function
Resolved
Part Number:
TS3A4751
Dear our clinet want to replace ADG4612, and we find
TS3A4751
Similar
Go Bravos
over 1 year ago
Switches & multiplexers
Switches & multiplexers forum
TS3A4751: What happens to NO1-4 when Vcc=0V
TI Thinks Resolved
Part Number:
TS3A4751
Hi team, Since the
TS3A4751
is a normally open switch, would it be valid to say that when VCC= 0V, NO1-4 would be disconnected(Hi-Z) from COM1-4? Thank you.
David_Wang
4 months ago
Switches & multiplexers
Switches & multiplexers forum
RE: SN74CBTLV3126: MDC/MDIO multiplexer
Hi, Kevin, The bandwidth is not specified for this device, so it's difficult for me to comment. Although for our families of bus FET switches (CBT-C, CB3T, CB3Q...etc), the bandwidth is typically in the range of 200 MHz, so it should support the...
Terry Wu2
over 1 year ago
Switches & multiplexers
Switches & multiplexers forum
TS3A4751: disconnect pin voltage
Resolved
Part Number:
TS3A4751
Hello Sirs, I have a question when
ts3a4751
NO1 pull up to 3.3V Vcc supply
lee peng kiat
over 2 years ago
Switches & multiplexers
Switches & multiplexers forum
TS3A4751: Bandwidth for TS3A4751
TI Thinks Resolved
Part Number:
TS3A4751
Dear Sir/Madam, The bandwidth indicated in datasheet for
TS3A4751
is 123MHz. But it didn't mention whether it is at -3dB ? However there is BW graph in datasheet shown below that at -3dB, the freq is about 70MHz. ...
Albert Guardiola
over 2 years ago
Switches & multiplexers
Switches & multiplexers forum
TS3A4751: Crosstalk in SPI bus switching
Part Number:
TS3A4751
Hi all, I have mounted
TS3A4751
PWR to switch a four-wire SPI bus to switch a FLASH memory to a graphic controller (RA8875). It looks like I may have a crosstalk issue in the switch circuit. my graphic controller can properly read...
Tony(JY) Jung
over 2 years ago
Switches & multiplexers
Switches & multiplexers forum
TS3A4751: Output/Input noise characteristic of TS3A4751
TI Thinks Resolved
Part Number:
TS3A4751
Hi team, I would like to know noise characteristic data on signal paths like PSRR, output noise level etc on
TS3A4751
. Because the block to be used this device is very sensitivity for noise characteristic so that my customer...
Francisco Zayas
over 2 years ago
Switches & multiplexers
Switches & multiplexers forum
TS3A4751: Current source switch for 1mA RTD sensor return current
Resolved
Part Number:
TS3A4751
Hi, We want to apply a constant current of 1mA to 4 RTD sensors (2 wire
<
>
Didn't find what you are looking for? Post a new question.
Ask a new question