• TL494: Push pull PWM converter design

  

  KUPPUSWAMY NAIDU

  TI Thinks Resolved

  Part Number: TL494 Other Parts Discussed in Thread: UCC28250 , UCC28251 , LM5030 Our Old design is based on TL494. We have a requirement of designing 3 pushpull converter supplies Vin [18-34] to work for -55 to +125 deg C : 1- 5V/22A 2- 28V/5A …

  • 7 days ago
  • Power management
  • Power management forum

• LM25037: Push-Pull controller

  

  PR

  TI Thinks Resolved

  Part Number: LM25037 Other Parts Discussed in Thread: , UCC2808A-2 Tool/software: Hello Team, I am looking for and DCDC controller for following application: Input voltage: From Battery ~7V Output voltage: Configurable to 250V and 420V Output…

  • 3 months ago
  • Power management
  • Power management forum

• SN74LVC2G17: SN74LVC2G17 Push-pull and Open drain quesiton

  

  Janet Lin

  Part Number: SN74LVC2G17 Hi E2E, The dstasheet of "SN74LVC2G17 " didn't mention if this is push-pull or open drain device. Could you double confirm if "SN74LVC2G17 " is Push-pull buffer? BR, Janet

  • 18 days ago
  • Logic
  • Logic forum

• TCAL6416: Open drain/ Push-pull

  

  Far Hung

  TI Thinks Resolved

  Part Number: TCAL6416 Other Parts Discussed in Thread: TCA6416 , , TCA6416A Tool/software: Hi Expert, I want to check that if the device can support open drain? And what is different between TCA6416 and TCA L 6416? Dell is confusing below, highlight…

  • 2 months ago
  • Interface
  • Interface forum

• LM25037-Q1: LM25037: Push-Pull Converter Desing (Continued)

  

  Hakan ANAR

  Part Number: LM25037-Q1 Other Parts Discussed in Thread: LM25037 Hello, I designed a push-pull converter using LM25037. Currently the converter is working without any problems. However, at nominal operating values, system efficiency is 85%. I want to…

  • 17 days ago
  • Power management
  • Power management forum

• UCC28951: PMP8740 purpose of Push-pull with RC impedance

  

  Nicola Fiorucci

  TI Thinks Resolved

  Part Number: UCC28951 Other Parts Discussed in Thread: PMP8740 Tool/software: Hi, based on PMP8740 reference design, what is the purpose of the RC network (100R + 0.1u + 0.022u) around the push-pull gate driver stage? Thanks

  • 1 month ago
  • Power management
  • Power management forum
Answered

• TPS7H6003-SP: TPS7H6003-SP usage with Push Pull converter with SR

  

  mohamed ElHammady

  Resolved

  Part Number: TPS7H6003-SP Other Parts Discussed in Thread: TPS7H5001-SP Hi, We would like to use TPS7H6003-SP with TPS7H5001-SP PWM controller to drive a Push Pull converter with SR. we have the schemtic below but without SR, can you suggest how the Schemtic…

  • Resolved

  • 21 days ago
  • Power management
  • Power management forum
Answered

• TMDX570LC43HDK: Push Button GIOA7

  

  Dobby

  Resolved

  Part Number: TMDX570LC43HDK Tool/software: Hi, İ can control push button status. Push button is GIO port A pin 7. But when i control port A pin 7, i dont appear push button values. I can see it on GIO portA pin 6. It says 7 in the document and on the…

  • Resolved

  • 5 months ago
  • Arm-based microcontrollers
  • Arm-based microcontrollers forum

• TXS0102: Open drain vs Push pull mode

  

  Vishnu Jayaraj

  TI Thinks Resolved

  Part Number: TXS0102 Tool/software: Hi, TP109(MCU2 RX) is the output and TP111 (MCU1 TX) is the input. MCU2 is in VCCB side and MCU1 is in VCCA side output waveform is not square pulse. Is this any limitation? The UART baud rate is 1228800…

  • 3 months ago
  • Arm-based microcontrollers
  • Arm-based microcontrollers forum

• RE: DRA821U: Push Buttons used on J7200 EVM

  

  Suman Anna

  Hi Jitendra, Please open a new thread. This thread has already deviated from your original push button query. The picture you are mentioning did not come through. regards Suman

  • 4 months ago
  • Processors
  • Processors forum

Didn't find what you are looking for? Post a new question.