This thread has been locked.
If you have a related question, please click the "Ask a related question" button in the top right corner. The newly created question will be automatically linked to this question.
i need to know is there any Evaluation board overcurrent monitoring and overcurrent detected it shut down my input available?
INA 301 EVM board can only sense over current and it alerts me. but i need to shut down my input when the alert current detected.
is there any EVM board available for current sense with overcurrent detect and shutdown circuit on board?
answer me quickly. I need it very urgent
Regards- Mehul Patel
We are glad that we were able to resolve this issue, and will now proceed to close this thread.
If you have further questions related to this thread, you may click "Ask a related question" below. The newly created question will be automatically linked to this question.
There are some things to note about the INA301:
- There are two modes of operation: transparent and latched and the mode is set by the RESET pin being pulled low or high respectively.
- In transparent mode, if the Vsense exceed the threshold set by VLIMIT then, ALERT pin will go low, but will go back up high as soon as the Vsense goes below the threshold voltage.
- In latched mode, if the Vsense exceeds the threshold voltage, the ALERT pin will go low and stay low even if Vsense goes back under the threshold. To reset the ALERT pin, the RESET pin must be briefly pulsed LOW.
Attached is a TINA simulation that shows one way to turn off a power supply using the INA300 and two transistors (T1 and T2, which can be both MOSFETs if desired). This would be useful if your the power source you're shutting down does not have a shutdown pin. This design also shows how it is necessay to operate the INA301/INA300 in the Latched mode, or else the system would go back and forth between ALERT high and low if what your are shutting down is what you are measuring as well. The INA301 does not have the RESET pin modeled, but the INA300 does have this ability modeled so I am using it for demonstrative purposes. The only difference is with the INA300 you set the mode (transparent of latched) using the LATCH pin. You also reset the ALERT output using the LATCH pin on the INA300 as well.
In reply to Peter Iliya:
ok sir, thnks.
my connections on INA301 board.
just check is it ok or not?
vcc= 5v , gnd=ground, 50 mili ohm resistor SMD type in between IN+ and IN-.( from supply side IN+ and from load side IN-)
jumper J1 on pin 2 to 3 for transparent mode and jumper j2 for alert enable.
there are some another soldered like pins named ALERT, RESET, AND VS , VOUT all is used for???
why are these pins given on board?
In reply to mehul patel:
Connections are good for normal operation. The soldered pins ALERT, RESET, VS, VOUT allow you to interact easily with the INA301 pins. The functions of these pins can be seen in the datasheet.
Current Sensing Applications
yes sir,but i want t o know is this pins are internally connected ?
or i have to connect it to anywhere externally?
which pin connections i have to do to operate this Evaluation board?
all of these pins i already have connected? then i cant understand what is the problem.
I assume you are referring to the problem in your other thread here:
Please review my suggestions in the other post. If you are still experiencing problem please reply back with:
- What are your connections for your INA301EVM.
- Do you have a measurement of the load current?
- What is the R3 (threshold-setting resistor) value for your INA301EVM. This needs to be changed if you want a threshold of something other than of 2.528V.
Current Sense Applications
heloo good morning sir,
my r3 for EVM is 31.6 Kohm . i want to measure max 500 mili ampere current . for 500 mA current i have used shunt resistor 50 mili ohm. but my problem is why my current is not passed through the circuit?
i have already done the experiment it works well before. but now it is not working.
Jason Bridgmon, TI Sensing Products Applications Support
Current Shunt Monitor Video Training Series
Hall Effect Sensor Video Training Series
TI makes no warranties and assumes no liability for applications assistance or customer product design. You are fully responsible for all design decisions and engineering with regard to your products, including decisions relating to application of TI products. By providing technical information, TI does not intend to offer or provide engineering services or advice concerning your designs.
All content and materials on this site are provided "as is". TI and its respective suppliers and providers of content make no representations about the suitability of these materials for any purpose and disclaim all warranties and conditions with regard to these materials, including but not limited to all implied warranties and conditions of merchantability, fitness for a particular purpose, title and non-infringement of any third party intellectual property right. TI and its respective suppliers and providers of content make no representations about the suitability of these materials for any purpose and disclaim all warranties and conditions with respect to these materials. No license, either express or implied, by estoppel or otherwise, is granted by TI. Use of the information on this site may require a license from a third party, or a license from TI.
TI is a global semiconductor design and manufacturing company. Innovate with 100,000+ analog ICs andembedded processors, along with software, tools and the industry’s largest sales/support staff.