• State Resolved
  • Locked Locked
  • Replies 7 replies
  • Subscribers 47 subscribers
  • Views 1858 views
  • Users 0 members are here
Support feedback
Options
Options
Similar topics

This thread has been locked.

If you have a related question, please click the "Ask a related question" button in the top right corner. The newly created question will be automatically linked to this question.

F28335 with ADS8556

Yash Bhagwat
Prodigy 40 points
Other Parts Discussed in Thread: ADS8556, TMS320F28335, SN74HC138

I am using F28335 and need to interface upto 24 external ADC channels from ADS8556 with the MCU ( these are additional channels beyond the inbuilt ADC). What is the best way to interface - SPI / McBSP?

Also, will I need to use an external channel multiplexer if using McBSP ?

  • 0
    TI__Guru 63205 points

    A possibility might be to use the parallel interface mode.  The TMS320F28335 supports an external memory interface called the XINTF.  You need to have some logic to expand the addresses with the 3 chip selects available on the interface.

  • 0 in reply to BrandonAzbell
    Prodigy 40 points

    Actually I plan to have following interfaces on F28335 -

    1. 16 channels using in-built ADCs

    2. 24 external ADC channels

    3. MCU - FPGA via EMIF/XINT

    4. External SDRAM via EMIF/XINT

    Given these interfaces, I think I will have to share the XINT address space for external RAM and FPGA connections; can ADC channels still be shared on same XINT ?

    In this scenario, will McBSP be a better option ... want your suggestions on these interfaces

  • 0 in reply to Yash Bhagwat
    TI__Guru**** 168605 points

    Hi Yash,

    I don't see any reason why keeping the ADS8556 on the EMIF would be an issue.  You'd have to address decode the /CS input (using something like an SN74HC138) and you could potentially use the SOC from the F28335 to trigger the CONVST inputs.  I believe the McBSP is in the low-speed clock domain which might be problematic in your control loop if you used the serial mode of the ADS8556.

  • 0 in reply to Tom Hendrick
    Prodigy 40 points

    Hi Tom,

    Thank you for your reply. I tried looking up some documentation and example code like adc_on_xintf and xintf_run_from. I'm not sure if I can use ADC channels, FPGA connection and SARAM simultaneously using same XINTF. Given a single data bus XD [31:0], even if I allocate something like ADC on Zone 0, FPGA on Zone 6 and may be SARAM on Zone 7 (separately addressed), can all interfaces work in parallel ?

  • 0 in reply to Yash Bhagwat
    TI__Guru**** 168605 points

    Hi Yash,

    How is your project going?  

  • 0 in reply to Tom Hendrick
    Prodigy 40 points

    Hi Tom,

    I'm working on the memory interface part of the project (FPGA-DSP via XINT, working on eZdsp). The issue of ADC channels has been solved. However, I'm looking into the analog pre-processing of the ADC inputs, especially for the inbuilt channels on F28335, by using something like INA 159. Can you suggest any reference designs for the same ?

  • 0 in reply to Yash Bhagwat
    TI__Guru**** 168605 points

    Hi Yash!

    I am glad to hear you are making progress!  I've not worked much with the ADC's inside the F28335.  You might try cruising around in the C2000 forum to see if there are any references there.