Other Parts Discussed in Thread: DLPC7540, , DLP650TEEVM
Hi,
I can almost get the JTAG Flash Programmer working, but the Flash Bootloader file seems to be missing.
See the attached document for details.File Missing.pdf
This thread has been locked.
If you have a related question, please click the "Ask a related question" button in the top right corner. The newly created question will be automatically linked to this question.
Hi,
I can almost get the JTAG Flash Programmer working, but the Flash Bootloader file seems to be missing.
See the attached document for details.File Missing.pdf
Hi Paul, Try the bootloader.bin file located here: https://tidrive.ext.ti.com/u/rE817JNPNcS-TzXn/180715bb-a4e2-4cbf-9b9b-fd4138373ab5?l
Well, that didn't work and has bricked my EVM. Attached are the steps I followed. Did I do it wrong?DLPC7540EVM - Bricked.docx
Hello Paul,
We're looking into your issue. Thank you for your patience.
Best,
Maxine
Paul,
Just looking at the bootloader.bin, it looks like it is size 49,712 = 0xC230; you had 0x8000 as the Size in the GUI. I would recommend changing that to 0xFFFF. Erase the whole flash, or at least from the start through the block containing 0xC230; then pram and set the size to 0xFFFF. Note: If I recall correctly, the GUI will change the larger size to the actual file size when you program the flash.
I don't know if this is your problem but that is what i first notice when I look at the information. Maybe that will help?
Regards,
Gary
Paul,
I am not able to test this on a DLPC7540 system. I have used a version of this tool a bit for a different platform; I was just providing a comment based on what I saw in the picture you sent in case that was the issue.
Maxine and/or made4engineering should be looking into this, I think.
Regards,
Gary
Please try this version:
https://tidrive.ext.ti.com/u/pv7GYZn-xk60_sZq/167a0a30-87de-4bcd-b43c-d87de4dbc35e?l
I tried the new bootloader.bin file and it doesn't work either. Did you test it with a DLPC7540EVM? The problem I am seeing is that the USB port is greyed out and I can't connect with the GUI to download theBootloader Issue.pdf firmware.
Try setting the size to 0x80000. Also if you can connect to the UART and get debug messages out it could be useful
It seems like it is almost working. See attached for more details....2843.Bootloader Issue.pdf
Paul,
Thanks for the file. Let us look at this and get back to you today or tomorrow.
Fizix
Make sure you are connected as so:
And you need to program your .img firmware as so:
Made4engineering does not understand the problem. I cannot do what is suggested above because the USB Connect button is greyed out as shown in the attached file called Mad4engineering.pdf.
This is what I think the problem is:
The bootloader.bin file that was provided only partially works because it has the bootloader functionality but no application code as you can see in the debug message in the file called bootloader issue.pdf. I think that if the bootloader.bin file was modified to have the bootloader functionality and an Application. The USB port would work.
The bootloader is all that is needed for USB connection. You are getting all of the correct feedback though UART and Device manager. Make sure the USB is connected to 7540EVM J2, and not to the JTAG. Also make sure there are no other programs running which could be already connected to the 7540 USB. Perhaps also avoid using USB hubs, and connect directly to PC.
Ok, now I can connect over USB, but when I do a firmware download it fails. Are you using a different program to download firmware?Firmware Download Failure.pdf
Remove J9 from the EVM, power cycle it. Use advanced mode in the GUI, and "Flash Program" like in the image earlier.
Ok, that worked. I can communicate and the splash screen comes up. I am having a new problem where the system does not automatically display the HDMI input. Is there a default setup for the board that I can send to it?
Just to confirm, you are now able to display video through your setup, just not by default?
Actually today I am not even getting the splash screen. See attached for the current status.Current Status.pdf
You will need to make sure the device is not coming up in bootloader mode
I have downloader the application code, and I have the jumper J9 removed. As shown in the last document, the GUI shows the status as EVM Status: Ready: Disp External
Doesn't that mean that the application code is running?
What feedback are you getting through UART now? You may want to check to make sure the ribbon cables are seated properly
It seems to be switching inputs constantly. I see the LOCK led for 30 seconds, then it goes off 30 seconds. The debug log says ""Connector timeout is detected!, switching to next connector....
I have swapped all the flex cables and tried a bunch of things but so far no luck getting the system back to normal. Any suggestions are appreciated.
---------------------------------------- Debug opened on URT0 I2C Port 1 initialized as Master port I2C Port 2 initialized as Master port I2C Port 0 initialized as Slave port eeprom: Content validated Cal data block CWLamp not in EEPROM : Using data from flash Cal data block SSI present in EEPROM. Data version = 0 Cal data block ADC not in EEPROM : Using data from flash Cal data block WpcSensor present in EEPROM. Data version = 4 Cal data block WpcBrightness present in EEPROM. Data version = 4 Cal data block XPR present in EEPROM. Data version = 4 Cal data block XPRWaveform not in EEPROM : Using data from flash Cal data block EdgeBlend not in EEPROM : Using data from flash Cal data block SurfaceCorrection won't fit in EEPROM : Using data from flash Cal data block SurfaceCorrection not in EEPROM : Using data from flash Cal data block BlendMap won't fit in EEPROM : Using data from flash Cal data block BlendMap not in EEPROM : Using data from flash API version: 4.5.0.0.0.0 App version: 4.5.0.0.0.0 sysmon: URT Cmd Handlerfailed to start pca9539: Error - iox failure. APIcc = -7 IT6807 - Configuring IT680x... digcontrol: Cfg complete digcontrol: Decoder 2 powerStandby complete digcontrol: Decoder 5 powerStandby complete datapath: PowerStandby Complete.. sysmon: DLPA100 not present illumination: Starting SSI Initialization... Configured SSI Driver Type = 0. Configuring sensor failed : -6. Initializing WPC configuration... SSI initialization failed. Sysmon: Transition to normal operating mode Initializing WPC Failed: -6 Initializing WPC calibration data Passed... Initializing WPC Brightness Table Failed: 0 datapath: autolock initialization passed digcontrol.c : line - 194 : digcontrol_powerNormal() iox_edid_init() failed digcontrol: powerNormal failed digcontrol.c : line - 194 : digcontrol_powerNormal() iox_edid_init() failed digcontrol: powerNormal failed digcontrol: powerNormal complete datapath: dig, adc, dec powerNormal source: SetUserSFGColor = 1 9 dispfmt_CalculateDisplayArea: X, Y, Width, Height = 0, 0, 3840, 2160 dispfmt:apply_disp: activeSource = 1, dispSrc = 1 source: SPLASH address: 0x104bf0b8 source: DisplaySplash size = 3840 x 2160 Blank screen is set to splash dispfmt_CalculateDisplayArea: X, Y, Width, Height = 0, 0, 3840, 2160 dispfmt: minPan, pan, maxPan:0, 0, 0 data = { 3840, 0, 3840 } dispfmt: minScan, scan, maxScan:0, 0, 0 data = { 2160, 0, 2160 } dispfmt_CalculateCroppedArea: X, Y, Width, Height = 0, 0, 3840, 2160 dispfmt:apply_disp: activeSource = 2, dispSrc = 2 datapath: Transition to IDLING on Vx1(ITE0) dispfmt_ConfigManualWarp(): LensCorrection enabled = 0 dispfmt_ConfigManualWarp: Config warping failed with error code -16 WarpValidateResult->InLinesPixOK = 1 WarpValidateResult->HCtrlOK = 0 WarpValidateResult->VCtrlOK = 1 WarpValidateResult->WrpPointsOK = 1 WarpValidateResult->FailRow = 0 WarpValidateResult->FailCol = 1 Actuator EEPROM size - 6 (where 0 = 0.125k,1 = 0.25k,2 = 0.5k,3 = 1k,4 = 2k,5 = 4k,6 = 8k) [Actuator Type]: 128 [AWC WG Auto-Offset]: 0 Actuator Type: 128 Unipolar: 0 XPR Param in EEPROM: MAtch Signature XPR 4 Way Orientation number: 22 XPR: Act subframe order: 0 3 1 2 XPR_4WAY_TIActGetActuatorData(): Read from EEPROM failed XPR_4WAY_TIActGetActuatorData(): Read from actuator failed!!! datapathf: XPR_4WAY_Init Failed SUCCESS: Product Configuration Valid, System Unlocked Controller Info: Id = 0x01030059, Name = DLPC7540 DMD Info: DeviceId = 0x600D0096, FuseId = 0x00060008, FuseBitString = 00010000110110110, Name = DLP651NE_ECD_p65_1080p illumination: Enabling SSI Driver... sysmon: Transition to normal mode complete sysmon: Completed _sysReset sysmon: Init Complete Startup Logo display time completed - 5039 milliseconds. Starting connector scan ------------------- SCANNING CONNECTOR : Vx1(ITE0) ---------------- Warning: No AFE1000/HW communcation found while attempting to place stand-by (However connector table seem to have a VGA entry) IT6807 - iteState is ITE_POWERUP digcontrol: Decoder 5 powerStandby complete datapath: Transition to SCANNING on Vx1(ITE0) digcontrol: ConfigureForSearch complete Event: Source Change Detected on channel Event: DSM Locked on channel digcontrol: FillSourceConfig - srcConfig: TotalArea.PixelsPerLine - 2200, TotalArea.LinesPerFrame - 1125, ActiveArea.FirstPixel - 192, ActiveArea.FirstLine - 41, ActiveArea.PixelsPerLine - 1920, ActiveArea.LinesPerFrame - 1080, PixelClockFreqInkHz - 148500, inputFrameRate - 59, srcColorType - RGB. srcConfig->IsInterlaced - FALSE, digcontrol: FillSourceConfig complete Is3D = FALSE dispfmt: DEI Disabled, Field Scaling Disabled dispfmt: Input frame rate is 59Hz dispfmt: input resolution: 1920 x 1080 dispfmt_CalculateDisplayArea: X, Y, Width, Height = 0, 0, 3840, 2160 dispfmt: minPan, pan, maxPan:0, 0, 0 data = { 1920, 0, 1920 } dispfmt: minScan, scan, maxScan:0, 0, 0 data = { 1080, 0, 1080 } dispfmt_CalculateCroppedArea: X, Y, Width, Height = 0, 0, 1920, 1080 dispfmt:apply_disp: activeSource = 0, dispSrc = 0 dispfmt: DISP_SetDisplay failed (ret=-16) CroppedArea = { 0, 0, 1920, 1080 } DisplayArea = { 0, 0, 3840, 2160 } datapath: dispfmt_ConfigureForSource failed 0 source: SPLASH address: 0x104bf0b8 source: DisplaySplash size = 3840 x 2160 Blank screen is set to splash dispfmt_CalculateDisplayArea: X, Y, Width, Height = 0, 0, 3840, 2160 dispfmt: minPan, pan, maxPan:0, 0, 0 data = { 3840, 0, 3840 } dispfmt: minScan, scan, maxScan:0, 0, 0 data = { 2160, 0, 2160 } dispfmt_CalculateCroppedArea: X, Y, Width, Height = 0, 0, 3840, 2160 dispfmt:apply_disp: activeSource = 2, dispSrc = 2 dispfmt: DISP_SetDisplay failed (ret=-16) CroppedArea = { 0, 0, 3840, 2160 } DisplayArea = { 0, 0, 3840, 2160 } Connector timeout is detected!, switching to next connector... ------------------- SCANNING CONNECTOR : Vx1(ITE1) ---------------- Warning: No AFE1000/HW communcation found while attempting to place stand-by (However connector table seem to have a VGA entry) IT6807 - IT6807_PortSelect = HDMI2 digcontrol: Decoder 5 powerStandby complete digcontrol: ConfigureForSearch complete Event: Source Change Detected on channel Source instability flagged by Front-end!, restarting Autlock... Connector timeout is detected!, switching to next connector... ------------------- SCANNING CONNECTOR : Vx1(DIRECT) ---------------- Warning: No AFE1000/HW communcation found while attempting to place stand-by (However connector table seem to have a VGA entry) IT6807 - HDMI in POWER_DOWN digcontrol: Decoder 2 powerStandby complete digcontrol: Decoder 2 powerStandby complete digcontrol: ConfigureForSearch complete Event: DSM Lost Lock on channel ------------------- SCANNING CONNECTOR : Vx1(ITE0) ---------------- Warning: No AFE1000/HW communcation found while attempting to place stand-by (However connector table seem to have a VGA entry) IT6807 - iteState is ITE_POWERUP IT6807 - IT6807_PortSelect = HDMI/MHL digcontrol: Decoder 5 powerStandby complete digcontrol: ConfigureForSearch complete Event: Source Change Detected on channel Event: DSM Locked on channel digcontrol: FillSourceConfig - srcConfig: TotalArea.PixelsPerLine - 2200, TotalArea.LinesPerFrame - 1125, ActiveArea.FirstPixel - 192, ActiveArea.FirstLine - 41, ActiveArea.PixelsPerLine - 1920, ActiveArea.LinesPerFrame - 1080, PixelClockFreqInkHz - 148500, inputFrameRate - 59, srcColorType - RGB. srcConfig->IsInterlaced - FALSE, digcontrol: FillSourceConfig complete Is3D = FALSE dispfmt: DEI Disabled, Field Scaling Disabled dispfmt: Input frame rate is 59Hz dispfmt: input resolution: 1920 x 1080 dispfmt_CalculateDisplayArea: X, Y, Width, Height = 0, 0, 3840, 2160 dispfmt: minPan, pan, maxPan:0, 0, 0 data = { 1920, 0, 1920 } dispfmt: minScan, scan, maxScan:0, 0, 0 data = { 1080, 0, 1080 } dispfmt_CalculateCroppedArea: X, Y, Width, Height = 0, 0, 1920, 1080 dispfmt:apply_disp: activeSource = 0, dispSrc = 0 dispfmt: DISP_SetDisplay failed (ret=-16) CroppedArea = { 0, 0, 1920, 1080 } DisplayArea = { 0, 0, 3840, 2160 } datapath: dispfmt_ConfigureForSource failed 0 source: SPLASH address: 0x104bf0b8 source: DisplaySplash size = 3840 x 2160 Blank screen is set to splash dispfmt_CalculateDisplayArea: X, Y, Width, Height = 0, 0, 3840, 2160 dispfmt: minPan, pan, maxPan:0, 0, 0 data = { 3840, 0, 3840 } dispfmt: minScan, scan, maxScan:0, 0, 0 data = { 2160, 0, 2160 } dispfmt_CalculateCroppedArea: X, Y, Width, Height = 0, 0, 3840, 2160 dispfmt:apply_disp: activeSource = 2, dispSrc = 2 dispfmt: DISP_SetDisplay failed (ret=-16) CroppedArea = { 0, 0, 3840, 2160 } DisplayArea = { 0, 0, 3840, 2160 } Connector timeout is detected!, switching to next connector... ------------------- SCANNING CONNECTOR : Vx1(ITE1) ---------------- Warning: No AFE1000/HW communcation found while attempting to place stand-by (However connector table seem to have a VGA entry) IT6807 - IT6807_PortSelect = HDMI2 digcontrol: Decoder 5 powerStandby complete digcontrol: ConfigureForSearch complete Event: Source Change Detected on channel Source instability flagged by Front-end!, restarting Autlock... Connector timeout is detected!, switching to next connector... ------------------- SCANNING CONNECTOR : Vx1(DIRECT) ---------------- Warning: No AFE1000/HW communcation found while attempting to place stand-by (However connector table seem to have a VGA entry) IT6807 - HDMI in POWER_DOWN digcontrol: Decoder 2 powerStandby complete digcontrol: Decoder 2 powerStandby complete digcontrol: ConfigureForSearch complete Event: DSM Lost Lock on channel ------------------- SCANNING CONNECTOR : Vx1(ITE0) ---------------- Warning: No AFE1000/HW communcation found while attempting to place stand-by (However connector table seem to have a VGA entry) IT6807 - iteState is ITE_POWERUP IT6807 - IT6807_PortSelect = HDMI/MHL digcontrol: Decoder 5 powerStandby complete digcontrol: ConfigureForSearch complete Event: Source Change Detected on channel Event: DSM Locked on channel digcontrol: FillSourceConfig - srcConfig: TotalArea.PixelsPerLine - 2200, TotalArea.LinesPerFrame - 1125, ActiveArea.FirstPixel - 192, ActiveArea.FirstLine - 41, ActiveArea.PixelsPerLine - 1920, ActiveArea.LinesPerFrame - 1080, PixelClockFreqInkHz - 148500, inputFrameRate - 59, srcColorType - RGB. srcConfig->IsInterlaced - FALSE, digcontrol: FillSourceConfig complete Is3D = FALSE dispfmt: DEI Disabled, Field Scaling Disabled dispfmt: Input frame rate is 59Hz dispfmt: input resolution: 1920 x 1080 dispfmt_CalculateDisplayArea: X, Y, Width, Height = 0, 0, 3840, 2160 dispfmt: minPan, pan, maxPan:0, 0, 0 data = { 1920, 0, 1920 } dispfmt: minScan, scan, maxScan:0, 0, 0 data = { 1080, 0, 1080 } dispfmt_CalculateCroppedArea: X, Y, Width, Height = 0, 0, 1920, 1080 dispfmt:apply_disp: activeSource = 0, dispSrc = 0 dispfmt: DISP_SetDisplay failed (ret=-16) CroppedArea = { 0, 0, 1920, 1080 } DisplayArea = { 0, 0, 3840, 2160 } datapath: dispfmt_ConfigureForSource failed 0 source: SPLASH address: 0x104bf0b8 source: DisplaySplash size = 3840 x 2160 Blank screen is set to splash dispfmt_CalculateDisplayArea: X, Y, Width, Height = 0, 0, 3840, 2160 dispfmt: minPan, pan, maxPan:0, 0, 0 data = { 3840, 0, 3840 } dispfmt: minScan, scan, maxScan:0, 0, 0 data = { 2160, 0, 2160 } dispfmt_CalculateCroppedArea: X, Y, Width, Height = 0, 0, 3840, 2160 dispfmt:apply_disp: activeSource = 2, dispSrc = 2 dispfmt: DISP_SetDisplay failed (ret=-16) CroppedArea = { 0, 0, 3840, 2160 } DisplayArea = { 0, 0, 3840, 2160 } Connector timeout is detected!, switching to next connector... ------------------- SCANNING CONNECTOR : Vx1(ITE1) ---------------- Warning: No AFE1000/HW communcation found while attempting to place stand-by (However connector table seem to have a VGA entry) IT6807 - IT6807_PortSelect = HDMI2 digcontrol: Decoder 5 powerStandby complete digcontrol: ConfigureForSearch complete Event: Source Change Detected on channel Source instability flagged by Front-end!, restarting Autlock... Connector timeout is detected!, switching to next connector... ------------------- SCANNING CONNECTOR : Vx1(DIRECT) ---------------- Warning: No AFE1000/HW communcation found while attempting to place stand-by (However connector table seem to have a VGA entry) IT6807 - HDMI in POWER_DOWN digcontrol: Decoder 2 powerStandby complete digcontrol: Decoder 2 powerStandby complete digcontrol: ConfigureForSearch complete Event: DSM Lost Lock on channel ------------------- SCANNING CONNECTOR : Vx1(ITE0) ---------------- Warning: No AFE1000/HW communcation found while attempting to place stand-by (However connector table seem to have a VGA entry) IT6807 - iteState is ITE_POWERUP IT6807 - IT6807_PortSelect = HDMI/MHL digcontrol: Decoder 5 powerStandby complete digcontrol: ConfigureForSearch complete Event: Source Change Detected on channel Event: DSM Locked on channel digcontrol: FillSourceConfig - srcConfig: TotalArea.PixelsPerLine - 2200, TotalArea.LinesPerFrame - 1125, ActiveArea.FirstPixel - 192, ActiveArea.FirstLine - 41, ActiveArea.PixelsPerLine - 1920, ActiveArea.LinesPerFrame - 1080, PixelClockFreqInkHz - 148500, inputFrameRate - 59, srcColorType - RGB. srcConfig->IsInterlaced - FALSE, digcontrol: FillSourceConfig complete Is3D = FALSE dispfmt: DEI Disabled, Field Scaling Disabled dispfmt: Input frame rate is 59Hz dispfmt: input resolution: 1920 x 1080 dispfmt_CalculateDisplayArea: X, Y, Width, Height = 0, 0, 3840, 2160 dispfmt: minPan, pan, maxPan:0, 0, 0 data = { 1920, 0, 1920 } dispfmt: minScan, scan, maxScan:0, 0, 0 data = { 1080, 0, 1080 } dispfmt_CalculateCroppedArea: X, Y, Width, Height = 0, 0, 1920, 1080 dispfmt:apply_disp: activeSource = 0, dispSrc = 0 dispfmt: DISP_SetDisplay failed (ret=-16) CroppedArea = { 0, 0, 1920, 1080 } DisplayArea = { 0, 0, 3840, 2160 } datapath: dispfmt_ConfigureForSource failed 0 source: SPLASH address: 0x104bf0b8 source: DisplaySplash size = 3840 x 2160 Blank screen is set to splash dispfmt_CalculateDisplayArea: X, Y, Width, Height = 0, 0, 3840, 2160 dispfmt: minPan, pan, maxPan:0, 0, 0 data = { 3840, 0, 3840 } dispfmt: minScan, scan, maxScan:0, 0, 0 data = { 2160, 0, 2160 } dispfmt_CalculateCroppedArea: X, Y, Width, Height = 0, 0, 3840, 2160 dispfmt:apply_disp: activeSource = 2, dispSrc = 2 dispfmt: DISP_SetDisplay failed (ret=-16) CroppedArea = { 0, 0, 3840, 2160 } DisplayArea = { 0, 0, 3840, 2160 }
Perhaps it could be the HDMI cable, or a problem with the PC display settings
I could not get the original DLPC7540EVM and DLP650TEEVM boards working again. I figured that I jacked up the firmware somehow. I was able to get the firmware downloaded, but I keep getting "Source instability flagged by Front-end!, restarting Autlock..."
So I bought a second set, and I am having the same problem straight out of the box ""Source instability flagged by Front-end!, restarting Autlock....
Any help would be appreciated. The second set of hardware is straight out of the box. I capture the debug info in the attached file.
---------------------------------------- Debug opened on URT0 I2C Port 1 initialized as Master port I2C Port 2 initialized as Master port I2C Port 0 initialized as Slave port eeprom: Content validated Cal data block CWLamp not in EEPROM : Using data from flash Cal data block SSI present in EEPROM. Data version = 0 Cal data block ADC not in EEPROM : Using data from flash Cal data block WpcSensor present in EEPROM. Data version = 4 Cal data block WpcBrightness present in EEPROM. Data version = 4 Cal data block XPR present in EEPROM. Data version = 4 Cal data block XPRWaveform not in EEPROM : Using data from flash Cal data block EdgeBlend not in EEPROM : Using data from flash Cal data block SurfaceCorrection won't fit in EEPROM : Using data from flash Cal data block SurfaceCorrection not in EEPROM : Using data from flash Cal data block BlendMap won't fit in EEPROM : Using data from flash Cal data block BlendMap not in EEPROM : Using data from flash API version: 4.5.0.0.0.0 App version: 4.5.0.0.0.0 sysmon: URT Cmd Handlerfailed to start pca9539: Error - iox failure. APIcc = -7 IT6807 - Configuring IT680x... digcontrol: Cfg complete digcontrol: Decoder 2 powerStandby complete digcontrol: Decoder 5 powerStandby complete datapath: PowerStandby Complete.. sysmon: DLPA100 not present illumination: Starting SSI Initialization... Configured SSI Driver Type = 0. Configuring sensor failed : -6. Initializing WPC configuration... SSI initialization failed. Sysmon: Transition to normal operating mode Initializing WPC Failed: -6 Initializing WPC calibration data Passed... Initializing WPC Brightness Table Failed: 0 datapath: autolock initialization passed digcontrol.c : line - 194 : digcontrol_powerNormal() iox_edid_init() failed digcontrol: powerNormal failed digcontrol.c : line - 194 : digcontrol_powerNormal() iox_edid_init() failed digcontrol: powerNormal failed digcontrol: powerNormal complete datapath: dig, adc, dec powerNormal source: SetUserSFGColor = 1 9 dispfmt_CalculateDisplayArea: X, Y, Width, Height = 0, 0, 3840, 2160 dispfmt:apply_disp: activeSource = 1, dispSrc = 1 source: SPLASH address: 0x104a84c0 source: DisplaySplash size = 3840 x 2160 Blank screen is set to splash dispfmt_CalculateDisplayArea: X, Y, Width, Height = 0, 0, 3840, 2160 dispfmt: minPan, pan, maxPan:0, 0, 0 data = { 3840, 0, 3840 } dispfmt: minScan, scan, maxScan:0, 0, 0 data = { 2160, 0, 2160 } dispfmt_CalculateCroppedArea: X, Y, Width, Height = 0, 0, 3840, 2160 dispfmt:apply_disp: activeSource = 2, dispSrc = 2 datapath: Transition to IDLING on Vx1(ITE0) dispfmt_ConfigManualWarp(): LensCorrection enabled = 0 dispfmt_ConfigManualWarp: Config warping failed with error code -16 WarpValidateResult->InLinesPixOK = 1 WarpValidateResult->HCtrlOK = 0 WarpValidateResult->VCtrlOK = 1 WarpValidateResult->WrpPointsOK = 1 WarpValidateResult->FailRow = 0 WarpValidateResult->FailCol = 1 Actuator EEPROM size - 6 (where 0 = 0.125k,1 = 0.25k,2 = 0.5k,3 = 1k,4 = 2k,5 = 4k,6 = 8k) [Actuator Type]: 128 [AWC WG Auto-Offset]: 0 Actuator Type: 128 Unipolar: 0 XPR Param in EEPROM: MAtch Signature XPR 4 Way Orientation number: 22 XPR: Act subframe order: 0 3 1 2 XPR_4WAY_TIActGetActuatorData(): Read from EEPROM failed XPR_4WAY_TIActGetActuatorData(): Read from actuator failed!!! datapathf: XPR_4WAY_Init Failed SUCCESS: Product Configuration Valid, System Unlocked Controller Info: Id = 0x01030059, Name = DLPC7540 DMD Info: DeviceId = 0x600D0096, FuseId = 0x00060008, FuseBitString = 00010000110110110, Name = DLP651NE_ECD_p65_1080p illumination: Enabling SSI Driver... sysmon: Transition to normal mode complete sysmon: Completed _sysReset sysmon: Init Complete Startup Logo display time completed - 5037 milliseconds. Starting connector scan ------------------- SCANNING CONNECTOR : Vx1(ITE0) ---------------- Warning: No AFE1000/HW communcation found while attempting to place stand-by (However connector table seem to have a VGA entry) IT6807 - iteState is ITE_POWERUP digcontrol: Decoder 5 powerStandby complete datapath: Transition to SCANNING on Vx1(ITE0) digcontrol: ConfigureForSearch complete Event: Source Change Detected on channel Event: DSM Locked on channel digcontrol: FillSourceConfig - srcConfig: TotalArea.PixelsPerLine - 2200, TotalArea.LinesPerFrame - 1125, ActiveArea.FirstPixel - 192, ActiveArea.FirstLine - 41, ActiveArea.PixelsPerLine - 1920, ActiveArea.LinesPerFrame - 1080, PixelClockFreqInkHz - 148500, inputFrameRate - 59, srcColorType - RGB. srcConfig->IsInterlaced - FALSE, digcontrol: FillSourceConfig complete Is3D = FALSE dispfmt: DEI Disabled, Field Scaling Disabled dispfmt: Input frame rate is 59Hz dispfmt: input resolution: 1920 x 1080 dispfmt_CalculateDisplayArea: X, Y, Width, Height = 0, 0, 3840, 2160 dispfmt: minPan, pan, maxPan:0, 0, 0 data = { 1920, 0, 1920 } dispfmt: minScan, scan, maxScan:0, 0, 0 data = { 1080, 0, 1080 } dispfmt_CalculateCroppedArea: X, Y, Width, Height = 0, 0, 1920, 1080 dispfmt:apply_disp: activeSource = 0, dispSrc = 0 dispfmt: DISP_SetDisplay failed (ret=-16) CroppedArea = { 0, 0, 1920, 1080 } DisplayArea = { 0, 0, 3840, 2160 } datapath: dispfmt_ConfigureForSource failed 0 source: SPLASH address: 0x104a84c0 source: DisplaySplash size = 3840 x 2160 Blank screen is set to splash dispfmt_CalculateDisplayArea: X, Y, Width, Height = 0, 0, 3840, 2160 dispfmt: minPan, pan, maxPan:0, 0, 0 data = { 3840, 0, 3840 } dispfmt: minScan, scan, maxScan:0, 0, 0 data = { 2160, 0, 2160 } dispfmt_CalculateCroppedArea: X, Y, Width, Height = 0, 0, 3840, 2160 dispfmt:apply_disp: activeSource = 2, dispSrc = 2 dispfmt: DISP_SetDisplay failed (ret=-16) CroppedArea = { 0, 0, 3840, 2160 } DisplayArea = { 0, 0, 3840, 2160 } Connector timeout is detected!, switching to next connector... ------------------- SCANNING CONNECTOR : Vx1(ITE1) ---------------- Warning: No AFE1000/HW communcation found while attempting to place stand-by (However connector table seem to have a VGA entry) IT6807 - IT6807_PortSelect = HDMI2 digcontrol: Decoder 5 powerStandby complete digcontrol: ConfigureForSearch complete Event: Source Change Detected on channel Source instability flagged by Front-end!, restarting Autlock... Connector timeout is detected!, switching to next connector... ------------------- SCANNING CONNECTOR : Vx1(DIRECT) ---------------- Warning: No AFE1000/HW communcation found while attempting to place stand-by (However connector table seem to have a VGA entry) IT6807 - HDMI in POWER_DOWN digcontrol: Decoder 2 powerStandby complete digcontrol: Decoder 2 powerStandby complete digcontrol: ConfigureForSearch complete Event: DSM Lost Lock on channel ------------------- SCANNING CONNECTOR : Vx1(ITE0) ---------------- Warning: No AFE1000/HW communcation found while attempting to place stand-by (However connector table seem to have a VGA entry) IT6807 - iteState is ITE_POWERUP IT6807 - IT6807_PortSelect = HDMI/MHL digcontrol: Decoder 5 powerStandby complete digcontrol: ConfigureForSearch complete Event: Source Change Detected on channel Event: DSM Locked on channel digcontrol: FillSourceConfig - srcConfig: TotalArea.PixelsPerLine - 2200, TotalArea.LinesPerFrame - 1125, ActiveArea.FirstPixel - 192, ActiveArea.FirstLine - 41, ActiveArea.PixelsPerLine - 1920, ActiveArea.LinesPerFrame - 1080, PixelClockFreqInkHz - 148500, inputFrameRate - 59, srcColorType - RGB. srcConfig->IsInterlaced - FALSE, digcontrol: FillSourceConfig complete Is3D = FALSE dispfmt: DEI Disabled, Field Scaling Disabled dispfmt: Input frame rate is 59Hz dispfmt: input resolution: 1920 x 1080 dispfmt_CalculateDisplayArea: X, Y, Width, Height = 0, 0, 3840, 2160 dispfmt: minPan, pan, maxPan:0, 0, 0 data = { 1920, 0, 1920 } dispfmt: minScan, scan, maxScan:0, 0, 0 data = { 1080, 0, 1080 } dispfmt_CalculateCroppedArea: X, Y, Width, Height = 0, 0, 1920, 1080 dispfmt:apply_disp: activeSource = 0, dispSrc = 0 dispfmt: DISP_SetDisplay failed (ret=-16) CroppedArea = { 0, 0, 1920, 1080 } DisplayArea = { 0, 0, 3840, 2160 } datapath: dispfmt_ConfigureForSource failed 0 source: SPLASH address: 0x104a84c0 source: DisplaySplash size = 3840 x 2160 Blank screen is set to splash dispfmt_CalculateDisplayArea: X, Y, Width, Height = 0, 0, 3840, 2160 dispfmt: minPan, pan, maxPan:0, 0, 0 data = { 3840, 0, 3840 } dispfmt: minScan, scan, maxScan:0, 0, 0 data = { 2160, 0, 2160 } dispfmt_CalculateCroppedArea: X, Y, Width, Height = 0, 0, 3840, 2160 dispfmt:apply_disp: activeSource = 2, dispSrc = 2 dispfmt: DISP_SetDisplay failed (ret=-16) CroppedArea = { 0, 0, 3840, 2160 } DisplayArea = { 0, 0, 3840, 2160 } Connector timeout is detected!, switching to next connector... ------------------- SCANNING CONNECTOR : Vx1(ITE1) ---------------- Warning: No AFE1000/HW communcation found while attempting to place stand-by (However connector table seem to have a VGA entry) IT6807 - IT6807_PortSelect = HDMI2 digcontrol: Decoder 5 powerStandby complete digcontrol: ConfigureForSearch complete Event: Source Change Detected on channel Source instability flagged by Front-end!, restarting Autlock... Connector timeout is detected!, switching to next connector... ------------------- SCANNING CONNECTOR : Vx1(DIRECT) ---------------- Warning: No AFE1000/HW communcation found while attempting to place stand-by (However connector table seem to have a VGA entry) IT6807 - HDMI in POWER_DOWN digcontrol: Decoder 2 powerStandby complete digcontrol: Decoder 2 powerStandby complete digcontrol: ConfigureForSearch complete Event: DSM Lost Lock on channel ------------------- SCANNING CONNECTOR : Vx1(ITE0) ---------------- Warning: No AFE1000/HW communcation found while attempting to place stand-by (However connector table seem to have a VGA entry) IT6807 - iteState is ITE_POWERUP IT6807 - IT6807_PortSelect = HDMI/MHL digcontrol: Decoder 5 powerStandby complete digcontrol: ConfigureForSearch complete Event: Source Change Detected on channel Event: DSM Locked on channel digcontrol: FillSourceConfig - srcConfig: TotalArea.PixelsPerLine - 2200, TotalArea.LinesPerFrame - 1125, ActiveArea.FirstPixel - 192, ActiveArea.FirstLine - 41, ActiveArea.PixelsPerLine - 1920, ActiveArea.LinesPerFrame - 1080, PixelClockFreqInkHz - 148500, inputFrameRate - 59, srcColorType - RGB. srcConfig->IsInterlaced - FALSE, digcontrol: FillSourceConfig complete Is3D = FALSE dispfmt: DEI Disabled, Field Scaling Disabled dispfmt: Input frame rate is 59Hz dispfmt: input resolution: 1920 x 1080 dispfmt_CalculateDisplayArea: X, Y, Width, Height = 0, 0, 3840, 2160 dispfmt: minPan, pan, maxPan:0, 0, 0 data = { 1920, 0, 1920 } dispfmt: minScan, scan, maxScan:0, 0, 0 data = { 1080, 0, 1080 } dispfmt_CalculateCroppedArea: X, Y, Width, Height = 0, 0, 1920, 1080 dispfmt:apply_disp: activeSource = 0, dispSrc = 0 dispfmt: DISP_SetDisplay failed (ret=-16) CroppedArea = { 0, 0, 1920, 1080 } DisplayArea = { 0, 0, 3840, 2160 } datapath: dispfmt_ConfigureForSource failed 0 source: SPLASH address: 0x104a84c0 source: DisplaySplash size = 3840 x 2160 Blank screen is set to splash dispfmt_CalculateDisplayArea: X, Y, Width, Height = 0, 0, 3840, 2160 dispfmt: minPan, pan, maxPan:0, 0, 0 data = { 3840, 0, 3840 } dispfmt: minScan, scan, maxScan:0, 0, 0 data = { 2160, 0, 2160 } dispfmt_CalculateCroppedArea: X, Y, Width, Height = 0, 0, 3840, 2160 dispfmt:apply_disp: activeSource = 2, dispSrc = 2 dispfmt: DISP_SetDisplay failed (ret=-16) CroppedArea = { 0, 0, 3840, 2160 } DisplayArea = { 0, 0, 3840, 2160 } Connector timeout is detected!, switching to next connector... ------------------- SCANNING CONNECTOR : Vx1(ITE1) ---------------- Warning: No AFE1000/HW communcation found while attempting to place stand-by (However connector table seem to have a VGA entry) IT6807 - IT6807_PortSelect = HDMI2 digcontrol: Decoder 5 powerStandby complete digcontrol: ConfigureForSearch complete Event: Source Change Detected on channel Source instability flagged by Front-end!, restarting Autlock...
What sort of setup to you have with your PC? Have you tried using a different computer?