This thread has been locked.

If you have a related question, please click the "Ask a related question" button in the top right corner. The newly created question will be automatically linked to this question.

  • TI Thinks Resolved

ISO7321C: Rising edge threshold and falling edge threshold for INx

Expert 4250 points
Zhou Fang67

Replies: 3

Views: 1091

Part Number: ISO7321C

Hi Team,

In Silicon Lab datasheet, e.g. SI86xx, the threshold is defined as VT+ 1.67V(typ) and VT- 1.23V(typ).

Do we have the specifications for ISO7321? These specs are required for input voltage tolerant test.

Thanks.

Zhou

Expert 4250 points
Zhou Fang67
  • Intellectual 2900 points
    Anand Reghunathan

    Hi Zhou,

    It is not specified in the ISO7321 datasheet but we can calculate the range from VIH and VIL parameters.

    VT+ and VT- would range between 0.8V and 2.0V. There would also be a typical hysteresis of 460mV at 5V supply operation. Calculating using the same would give you the below table.

    Minimum Maximum
    VT+ 1.26 2.0
    VT- 0.8 1.54

    Hope this helps.

    Regards,
    Anand Reghunathan

  • Expert 4250 points
    Zhou Fang67

    In reply to Anand Reghunathan:

    Hi Anand,

    Thanks for your replay.

    I can see a overlap from 1.26V to 1.54V by calculation. The logic is not correct in cross-region.

    Do we have design value or test value to show?
    Do we have typical value?

    Thanks.
    Zhou
  • Intellectual 2900 points
    Anand Reghunathan

    In reply to Zhou Fang67:

    Hi Zhou,

    There will always be a guaranteed hysteresis of typical value 460mV. (VT+) = (VT-) + 460mV
    So when VT+ is at its minimum value, VT- will also be at its minimum value. Similarly for the maximum values also.
    This will ensure that there will be no overlap happening over the full range.

    Example:
    When VT- is 1.5V, VT+ will typically be 460mV higher. (VT+) = 1.96V.
    When VT+ is 1.3V, VT- will typically be 460mV lower. (VT+) = 0.84V.

    They typical value should fall near the average of min and max but I can't give it an exact value.

    Regards,
    Anand Reghunathan

This thread has been locked.

If you have a related question, please click the "Ask a related question" button in the top right corner. The newly created question will be automatically linked to this question.


All content and materials on this site are provided "as is". TI and its respective suppliers and providers of content make no representations about the suitability of these materials for any purpose and disclaim all warranties and conditions with regard to these materials, including but not limited to all implied warranties and conditions of merchantability, fitness for a particular purpose, title and non-infringement of any third party intellectual property right. No license, either express or implied, by estoppel or otherwise, is granted by TI. Use of the information on this site may require a license from a third party, or a license from TI.

Content on this site may contain or be subject to specific guidelines or limitations on use. All postings and use of the content on this site are subject to the Terms of use of the site; third parties using this content agree to abide by any limitations or guidelines and to comply with the Terms of use of this site. TI, its suppliers and providers of content reserve the right to make corrections, deletions, modifications, enhancements, improvements and other changes to the content and materials, its products, programs and services at any time or to move or discontinue any content, products, programs, or services without notice.

TI worldwide | Contact us | myTI login | Corporate citizenship

TI is a global semiconductor design and manufacturing company. Innovate with 100,000+ analog ICs and
embedded processors, along with software, tools and the industry’s largest sales/support staff.

© Copyright 1995-2021 Texas Instruments Incorporated. All rights reserved.
Trademarks | Privacy policy | Terms of use