LAUNCHXL-F28027F: DRV8353RS-EVM, LAUNCHXL-F28027F, ISO-F28027F

/* --COPYRIGHT--,BSD
 * Copyright (c) 2012, Texas Instruments Incorporated
 * All rights reserved.
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions
 * are met:
 *
 * *  Redistributions of source code must retain the above copyright
 *    notice, this list of conditions and the following disclaimer.
 *
 * *  Redistributions in binary form must reproduce the above copyright
 *    notice, this list of conditions and the following disclaimer in the
 *    documentation and/or other materials provided with the distribution.
 *
 * *  Neither the name of Texas Instruments Incorporated nor the names of
 *    its contributors may be used to endorse or promote products derived
 *    from this software without specific prior written permission.
 *
 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
 * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
 * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
 * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
 * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
 * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
 * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS;
 * OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
 * WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR
 * OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
 * EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
 * --/COPYRIGHT--*/
//! \file   solutions/instaspin_foc/src/proj_lab05b.c
//! \brief Adjusting the speed controller
//!
//! (C) Copyright 2011, Texas Instruments, Inc.

//! \defgroup PROJ_LAB05b PROJ_LAB05b
//@{

//! \defgroup PROJ_LAB05b_OVERVIEW Project Overview
//!
//! Adjusting the supplied speed controller
//!

// **************************************************************************
// the includes

// system includes
#include <math.h>
#include "main.h"

#ifdef FLASH
#pragma CODE_SECTION(mainISR,"ramfuncs");
#endif

// Include header files used in the main function


// **************************************************************************
// the defines

#define LED_BLINK_FREQ_Hz   5

//! \brief Defines the GPIO pin number for drv8353 Switch 3
#define HAL_GPIO_SW3 GPIO_Number_12

// **************************************************************************
// the globals

uint_least16_t gCounter_updateGlobals = 0;

bool Flag_Latch_softwareUpdate = true;

bool gSw3;


CTRL_Handle ctrlHandle;

#ifdef CSM_ENABLE
#pragma DATA_SECTION(halHandle,"rom_accessed_data");
#endif
HAL_Handle halHandle;

#ifdef CSM_ENABLE
#pragma DATA_SECTION(gUserParams,"rom_accessed_data");
#endif
USER_Params gUserParams;

HAL_PwmData_t gPwmData = {_IQ(0.0), _IQ(0.0), _IQ(0.0)};

HAL_AdcData_t gAdcData;

_iq gMaxCurrentSlope = _IQ(0.0);
/*Motor ID*/
_iq gLs_pu = _IQ30(0.0);
uint_least8_t gLs_qFmt = 0;
uint_least8_t gMax_Ls_qFmt = 0;


#ifdef FAST_ROM_V1p6
CTRL_Obj *controller_obj;
#else
#ifdef CSM_ENABLE
#pragma DATA_SECTION(ctrl,"rom_accessed_data");
#endif
CTRL_Obj ctrl;				//v1p7 format
#endif

uint16_t gLEDcnt = 0;

volatile MOTOR_Vars_t gMotorVars = MOTOR_Vars_INIT;
//volatile DRV8x_Vars_t gDrv8xVars = DRV8x_Vars_INIT;
_iq24 gPotentiometer = _IQ(0.0);
uint16_t gDeviceVariant = 0xFF;

#ifdef FLASH
// Used for running BackGround in flash, and ISR in RAM
extern uint16_t *RamfuncsLoadStart, *RamfuncsLoadEnd, *RamfuncsRunStart;

#ifdef CSM_ENABLE
extern uint16_t *econst_start, *econst_end, *econst_ram_load;
extern uint16_t *switch_start, *switch_end, *switch_ram_load;
#endif
#endif


#ifdef DRV8301_SPI
// Watch window interface to the 8301 SPI
DRV_SPI_8301_Vars_t gDrvSpi8301Vars;
#endif

#ifdef DRV8305_SPI
// Watch window interface to the 8305 SPI
DRV_SPI_8305_Vars_t gDrvSpi8305Vars;
#endif


#ifdef DRV8353_SPI
// Watch window interface to the 8305 SPI
DRV_SPI_8353_Vars_t gDrvSpi8353Vars;
#endif

_iq gFlux_pu_to_Wb_sf;

_iq gFlux_pu_to_VpHz_sf;

_iq gTorque_Ls_Id_Iq_pu_to_Nm_sf;

_iq gTorque_Flux_Iq_pu_to_Nm_sf;

// **************************************************************************
// the functions

void main(void)
{
  uint_least8_t estNumber = 0;

#ifdef FAST_ROM_V1p6
  uint_least8_t ctrlNumber = 1;
#endif

  // Only used if running from FLASH
  // Note that the variable FLASH is defined by the project
  #ifdef FLASH
  // Copy time critical code and Flash setup code to RAM
  // The RamfuncsLoadStart, RamfuncsLoadEnd, and RamfuncsRunStart
  // symbols are created by the linker. Refer to the linker files.
  memCopy((uint16_t *)&RamfuncsLoadStart,(uint16_t *)&RamfuncsLoadEnd,(uint16_t *)&RamfuncsRunStart);

  #ifdef CSM_ENABLE
    //copy .econst to unsecure RAM
    if(*econst_end - *econst_start)
      {
        memCopy((uint16_t *)&econst_start,(uint16_t *)&econst_end,(uint16_t *)&econst_ram_load);
      }

    //copy .switch ot unsecure RAM
    if(*switch_end - *switch_start)
      {
        memCopy((uint16_t *)&switch_start,(uint16_t *)&switch_end,(uint16_t *)&switch_ram_load);
      }
  #endif
  #endif

  // initialize the hardware abstraction layer
  halHandle = HAL_init(&hal,sizeof(hal));

  // check for errors in user parameters
  USER_checkForErrors(&gUserParams);


  // store user parameter error in global variable
  gMotorVars.UserErrorCode = USER_getErrorCode(&gUserParams);


  // do not allow code execution if there is a user parameter error
  if(gMotorVars.UserErrorCode != USER_ErrorCode_NoError)
    {
      for(;;)
        {
          gMotorVars.Flag_enableSys = false;
        }
    }


  // initialize the user parameters
  USER_setParams(&gUserParams);


  // set the hardware abstraction layer parameters
  HAL_setParams(halHandle,&gUserParams);


  // initialize the controller
#ifdef FAST_ROM_V1p6
  ctrlHandle = CTRL_initCtrl(ctrlNumber, estNumber);  		//v1p6 format (06xF and 06xM devices)
  controller_obj = (CTRL_Obj *)ctrlHandle;
#else
  ctrlHandle = CTRL_initCtrl(estNumber,&ctrl,sizeof(ctrl));	//v1p7 format default
#endif


  {
    CTRL_Version version;

    // get the version number
    CTRL_getVersion(ctrlHandle,&version);

    gMotorVars.CtrlVersion = version;
  }


  // set the default controller parameters
  CTRL_setParams(ctrlHandle,&gUserParams);


  // setup faults
  HAL_setupFaults(halHandle);


  // initialize the interrupt vector table
  HAL_initIntVectorTable(halHandle);


  // enable the ADC interrupts
  HAL_enableAdcInts(halHandle);


  // enable global interrupts
  HAL_enableGlobalInts(halHandle);


  // enable debug interrupts
  HAL_enableDebugInt(halHandle);


  // disable the PWM
  HAL_disablePwm(halHandle);


#ifdef DRV8301_SPI
  // turn on the DRV8301 if present
  HAL_enableDrv(halHandle);
  // initialize the DRV8301 interface
  HAL_setupDrvSpi(halHandle,&gDrvSpi8301Vars);
#endif

#ifdef DRV8305_SPI
  // turn on the DRV8305 if present
  HAL_enableDrv(halHandle);
  // initialize the DRV8305 interface
  HAL_setupDrvSpi(halHandle,&gDrvSpi8305Vars);
#endif

#ifdef DRV8353
  HAL_enableDrv(halHandle);
#endif
#ifdef DRV8353_SPI
  // initialize the DRV8353 interface
  if(gDeviceVariant)
	  HAL_setupDrvSpi(halHandle,&gDrvSpi8353Vars);
#endif

  // enable DC bus compensation
  CTRL_setFlag_enableDcBusComp(ctrlHandle, true);


  // compute scaling factors for flux and torque calculations
  gFlux_pu_to_Wb_sf = USER_computeFlux_pu_to_Wb_sf();
  gFlux_pu_to_VpHz_sf = USER_computeFlux_pu_to_VpHz_sf();
  gTorque_Ls_Id_Iq_pu_to_Nm_sf = USER_computeTorque_Ls_Id_Iq_pu_to_Nm_sf();
  gTorque_Flux_Iq_pu_to_Nm_sf = USER_computeTorque_Flux_Iq_pu_to_Nm_sf();

  // turn on the DRV8305 if present
    gPotentiometer = HAL_readPotentiometerData(halHandle);
    gPotentiometer = HAL_readPotentiometerData(halHandle);
    gPotentiometer = HAL_readPotentiometerData(halHandle);
    gPotentiometer = HAL_readPotentiometerData(halHandle);

    if((gPotentiometer) < USER_DRVID_ADC_V)
	  gDeviceVariant = DRV8353RS;
	else
	  gDeviceVariant = DRV8353RH;


  for(;;)
  {

    // Waiting for enable system flag to be set
//*    while(!(gMotorVars.Flag_enableSys));
      gMotorVars.Flag_enableSys = true;

    // Enable the Library internal PI.  Iq is referenced by the speed PI now
    CTRL_setFlag_enableSpeedCtrl(ctrlHandle, true);


    // loop while the enable system flag is true
    while(gMotorVars.Flag_enableSys)
      {
        CTRL_Obj *obj = (CTRL_Obj *)ctrlHandle;

        // increment counters
        gCounter_updateGlobals++;
        if(gMotorVars.Flag_updateUserdoth)
        {
            // set the enable controller flag to false
            CTRL_setFlag_enableCtrl(ctrlHandle,false);

            // set the default controller parameters
            CTRL_setParams(ctrlHandle,&gUserParams);

            // disable the PWM
            HAL_disablePwm(halHandle);
            gMotorVars.Flag_Run_Identify = 0;

            gMotorVars.Flag_updateUserdoth = 0;
        }

        // enable/disable the use of motor parameters being loaded from user.h
        CTRL_setFlag_enableUserMotorParams(ctrlHandle,gMotorVars.Flag_enableUserParams);

        // enable/disable Rs recalibration during motor startup
        EST_setFlag_enableRsRecalc(obj->estHandle,gMotorVars.Flag_enableRsRecalc);

        // enable/disable automatic calculation of bias values
        CTRL_setFlag_enableOffset(ctrlHandle,gMotorVars.Flag_enableOffsetcalc);


        if(CTRL_isError(ctrlHandle))
          {
            // set the enable controller flag to false
            CTRL_setFlag_enableCtrl(ctrlHandle,false);

            // set the enable system flag to false
            gMotorVars.Flag_enableSys = false;

            // disable the PWM
            HAL_disablePwm(halHandle);

          }
        else
          {
            // update the controller state
            bool flag_ctrlStateChanged = CTRL_updateState(ctrlHandle);

            // enable or disable the control
            CTRL_setFlag_enableCtrl(ctrlHandle, gMotorVars.Flag_Run_Identify);

            if(flag_ctrlStateChanged)
              {
                CTRL_State_e ctrlState = CTRL_getState(ctrlHandle);
                /* Motor Identification*/
                EST_State_e estState = EST_getState(obj->estHandle);

                if(ctrlState == CTRL_State_OffLine)
                  {
                    // enable the PWM
                    HAL_enablePwm(halHandle);
                  }
                else if(ctrlState == CTRL_State_OnLine)
                  {
                	/* Motor Identification*/
                	if(((estState < EST_State_LockRotor) || (estState > EST_State_MotorIdentified)) && (!gMotorVars.Flag_updateUserdoth))
                    //if(gMotorVars.Flag_enableOffsetcalc == true)
                    {
                      // update the ADC bias values
                      HAL_updateAdcBias(halHandle);
                    }
                    else
                    {
                      // set the current bias
                      HAL_setBias(halHandle,HAL_SensorType_Current,0,_IQ(I_A_offset));
                      HAL_setBias(halHandle,HAL_SensorType_Current,1,_IQ(I_B_offset));
                      HAL_setBias(halHandle,HAL_SensorType_Current,2,_IQ(I_C_offset));

                      // set the voltage bias
                      HAL_setBias(halHandle,HAL_SensorType_Voltage,0,_IQ(V_A_offset));
                      HAL_setBias(halHandle,HAL_SensorType_Voltage,1,_IQ(V_B_offset));
                      HAL_setBias(halHandle,HAL_SensorType_Voltage,2,_IQ(V_C_offset));
                    }

                    // Return the bias value for currents
                    gMotorVars.I_bias.value[0] = HAL_getBias(halHandle,HAL_SensorType_Current,0);
                    gMotorVars.I_bias.value[1] = HAL_getBias(halHandle,HAL_SensorType_Current,1);
                    gMotorVars.I_bias.value[2] = HAL_getBias(halHandle,HAL_SensorType_Current,2);

                    // Return the bias value for voltages
                    gMotorVars.V_bias.value[0] = HAL_getBias(halHandle,HAL_SensorType_Voltage,0);
                    gMotorVars.V_bias.value[1] = HAL_getBias(halHandle,HAL_SensorType_Voltage,1);
                    gMotorVars.V_bias.value[2] = HAL_getBias(halHandle,HAL_SensorType_Voltage,2);

                    // enable the PWM
                    HAL_enablePwm(halHandle);
                  }
                else if(ctrlState == CTRL_State_Idle)
                  {
                    // disable the PWM
                    HAL_disablePwm(halHandle);
                    gMotorVars.Flag_Run_Identify = false;
                  }

                if((CTRL_getFlag_enableUserMotorParams(ctrlHandle) == true) &&
                  (ctrlState > CTRL_State_Idle) &&
                  (gMotorVars.CtrlVersion.minor == 6))
                  {
                    // call this function to fix 1p6
                    USER_softwareUpdate1p6(ctrlHandle);
                  }

              }
          }


        if((EST_isMotorIdentified(obj->estHandle)) && (!(gMotorVars.Flag_updateUserdoth)))
          {
            // set the current ramp
            EST_setMaxCurrentSlope_pu(obj->estHandle,gMaxCurrentSlope);
            gMotorVars.Flag_MotorIdentified = true;

            // set the speed reference
            CTRL_setSpd_ref_krpm(ctrlHandle,gMotorVars.SpeedRef_krpm);

            // set the speed acceleration
            CTRL_setMaxAccel_pu(ctrlHandle,_IQmpy(MAX_ACCEL_KRPMPS_SF,gMotorVars.MaxAccel_krpmps));
            if(Flag_Latch_softwareUpdate)
            {
              Flag_Latch_softwareUpdate = false;

              USER_calcPIgains(ctrlHandle);

              // initialize the watch window kp and ki current values with pre-calculated values
              gMotorVars.Kp_Idq = CTRL_getKp(ctrlHandle,CTRL_Type_PID_Id);
              gMotorVars.Ki_Idq = CTRL_getKi(ctrlHandle,CTRL_Type_PID_Id);

              // initialize the watch window kp and ki values with pre-calculated values
              gMotorVars.Kp_spd = CTRL_getKp(ctrlHandle,CTRL_Type_PID_spd);
              gMotorVars.Ki_spd = CTRL_getKi(ctrlHandle,CTRL_Type_PID_spd);
            }

          }
        else
          {
            Flag_Latch_softwareUpdate = true;

            // the estimator sets the maximum current slope during identification
            gMaxCurrentSlope = EST_getMaxCurrentSlope_pu(obj->estHandle);
          }


        // when appropriate, update the global variables
        if(gCounter_updateGlobals >= NUM_MAIN_TICKS_FOR_GLOBAL_VARIABLE_UPDATE)
          {
            // reset the counter
            gCounter_updateGlobals = 0;

            updateGlobalVariables_motor(ctrlHandle);
          }
        /*Motor Identification*/
        if((CTRL_getMotorType(ctrlHandle) == MOTOR_Type_Induction) && (!gMotorVars.Flag_updateUserdoth))
          {
            // recalculate Kp and Ki gains to fix the R/L limitation of 2000.0, and Kp limit to 0.11
            recalcKpKi(ctrlHandle);

            // set electrical frequency limit to zero while identifying an induction motor
            setFeLimitZero(ctrlHandle);

            // calculate Dir_qFmt for acim motors
            acim_Dir_qFmtCalc(ctrlHandle);
          }
        else
          {
            // recalculate Kp and Ki gains to fix the R/L limitation of 2000.0, and Kp limit to 0.11
        	// as well as recalculates gains based on estimator state to allow low inductance pmsm to id
        	recalcKpKiPmsm(ctrlHandle);

            // calculate an Ls qFmt that allows ten times smaller inductance compared to Lhf
            CTRL_calcMax_Ls_qFmt(ctrlHandle, &gMax_Ls_qFmt);

            gLs_pu = EST_getLs_d_pu(obj->estHandle);
            gLs_qFmt = EST_getLs_qFmt(obj->estHandle);
          }


        /*Motor Identification*/
        // update Kp and Ki gains
        //updateKpKiGains(ctrlHandle);

        // enable/disable the forced angle
        EST_setFlag_enableForceAngle(obj->estHandle,gMotorVars.Flag_enableForceAngle);

        // enable or disable power warp
        CTRL_setFlag_enablePowerWarp(ctrlHandle,gMotorVars.Flag_enablePowerWarp);

#ifdef DRV8301_SPI
        HAL_writeDrvData(halHandle,&gDrvSpi8301Vars);

        HAL_readDrvData(halHandle,&gDrvSpi8301Vars);
#endif
#ifdef DRV8305_SPI
        HAL_writeDrvData(halHandle,&gDrvSpi8305Vars);

        HAL_readDrvData(halHandle,&gDrvSpi8305Vars);
#endif
#ifdef DRV8353_SPI
        if(gDeviceVariant)
        {
			HAL_writeDrvData(halHandle,&gDrvSpi8353Vars);

			HAL_readDrvData(halHandle,&gDrvSpi8353Vars);
        }
#endif
      } // end of while(gFlag_enableSys) loop


    // disable the PWM
    HAL_disablePwm(halHandle);

    // set the default controller parameters (Reset the control to re-identify the motor)
    CTRL_setParams(ctrlHandle,&gUserParams);
    gMotorVars.Flag_Run_Identify = false;

  } // end of for(;;) loop

} // end of main() function


interrupt void mainISR(void)
{

  // toggle status LED
  if(++gLEDcnt >= (uint_least32_t)(USER_ISR_FREQ_Hz / LED_BLINK_FREQ_Hz))
  {
    HAL_toggleLed(halHandle,(GPIO_Number_e)HAL_Gpio_LED2);
    gLEDcnt = 0;
  }


  // To call the function and assign the value.
//*  gSw3=HAL_readGpio(halHandle, HAL_GPIO_SW3);


  // To call the function and assign the value, To start and stop the motor.
  {
  // enable or disable the system
  gSw3 = HAL_readGpio(halHandle, HAL_GPIO_SW3);
  if (gSw3==false)
  {
  gMotorVars.Flag_enableSys = true;
  gMotorVars.Flag_Run_Identify = true;
  }
  else
  {
  gMotorVars.Flag_enableSys = false;
  gMotorVars.Flag_Run_Identify = false;
  }
  }



  // acknowledge the ADC interrupt
  HAL_acqAdcInt(halHandle,ADC_IntNumber_1);


  // convert the ADC data
  HAL_readAdcData(halHandle,&gAdcData);


  // run the controller
  CTRL_run(ctrlHandle,halHandle,&gAdcData,&gPwmData);


  // write the PWM compare values
  HAL_writePwmData(halHandle,&gPwmData);


  // setup the controller
  CTRL_setup(ctrlHandle);
  if(CTRL_getMotorType(ctrlHandle) == MOTOR_Type_Pm)
    {
      // reset Ls Q format to a higher value when Ls identification starts
      CTRL_resetLs_qFmt(ctrlHandle, gMax_Ls_qFmt);
    }



  return;
} // end of mainISR() function


void updateGlobalVariables_motor(CTRL_Handle handle)
{
  CTRL_Obj *obj = (CTRL_Obj *)handle;

  // get the speed estimate
  gMotorVars.Speed_krpm = EST_getSpeed_krpm(obj->estHandle);

  // get the real time speed reference coming out of the speed trajectory generator
  gMotorVars.SpeedTraj_krpm = _IQmpy(CTRL_getSpd_int_ref_pu(handle),EST_get_pu_to_krpm_sf(obj->estHandle));

  // get the torque estimate
  gMotorVars.Torque_Nm = USER_computeTorque_Nm(handle, gTorque_Flux_Iq_pu_to_Nm_sf, gTorque_Ls_Id_Iq_pu_to_Nm_sf);

  // get the magnetizing current
  gMotorVars.MagnCurr_A = EST_getIdRated(obj->estHandle);

  // get the rotor resistance
  gMotorVars.Rr_Ohm = EST_getRr_Ohm(obj->estHandle);

  // get the stator resistance
  gMotorVars.Rs_Ohm = EST_getRs_Ohm(obj->estHandle);

  // get the stator inductance in the direct coordinate direction
  gMotorVars.Lsd_H = EST_getLs_d_H(obj->estHandle);

  // get the stator inductance in the quadrature coordinate direction
  gMotorVars.Lsq_H = EST_getLs_q_H(obj->estHandle);

  // get the flux in V/Hz in floating point
  gMotorVars.Flux_VpHz = EST_getFlux_VpHz(obj->estHandle);

  // get the flux in Wb in fixed point
  gMotorVars.Flux_Wb = USER_computeFlux(handle, gFlux_pu_to_Wb_sf);

  // get the controller state
  gMotorVars.CtrlState = CTRL_getState(handle);

  // get the estimator state
  gMotorVars.EstState = EST_getState(obj->estHandle);

  // Get the DC buss voltage
  gMotorVars.VdcBus_kV = _IQmpy(gAdcData.dcBus,_IQ(USER_IQ_FULL_SCALE_VOLTAGE_V/1000.0));

  return;
} // end of updateGlobalVariables_motor() function


void updateKpKiGains(CTRL_Handle handle)
{
  if((gMotorVars.CtrlState == CTRL_State_OnLine) && (gMotorVars.Flag_MotorIdentified == true) && (Flag_Latch_softwareUpdate == false))
    {
      // set the kp and ki speed values from the watch window
      CTRL_setKp(handle,CTRL_Type_PID_spd,gMotorVars.Kp_spd);
      CTRL_setKi(handle,CTRL_Type_PID_spd,gMotorVars.Ki_spd);

      // set the kp and ki current values for Id and Iq from the watch window
      CTRL_setKp(handle,CTRL_Type_PID_Id,gMotorVars.Kp_Idq);
      CTRL_setKi(handle,CTRL_Type_PID_Id,gMotorVars.Ki_Idq);
      CTRL_setKp(handle,CTRL_Type_PID_Iq,gMotorVars.Kp_Idq);
      CTRL_setKi(handle,CTRL_Type_PID_Iq,gMotorVars.Ki_Idq);
	}

  return;
} // end of updateKpKiGains() function
void CTRL_resetLs_qFmt(CTRL_Handle handle, const uint_least8_t Ls_qFmt)
{
  CTRL_Obj *obj = (CTRL_Obj *)handle;
  static bool LsResetLatch = false;

  // reset Ls Q format to a higher value when Ls identification starts
  if(EST_getState(obj->estHandle) == EST_State_Ls)
    {
      if((EST_getLs_d_pu(obj->estHandle) != _IQ30(0.0)) && (LsResetLatch == false))
        {
          EST_setLs_qFmt(obj->estHandle, Ls_qFmt);
          LsResetLatch = true;
        }
    }
  else
    {
      LsResetLatch = false;
    }

  return;
} // end of CTRL_resetLs_qFmt() function


void recalcKpKiPmsm(CTRL_Handle handle)
{
  CTRL_Obj *obj = (CTRL_Obj *)handle;
  EST_State_e EstState = EST_getState(obj->estHandle);

  if((EST_isMotorIdentified(obj->estHandle) == false) && (EstState == EST_State_Rs))
    {
      float_t Lhf = CTRL_getLhf(handle);
      float_t Rhf = CTRL_getRhf(handle);
      float_t RhfoverLhf = Rhf/Lhf;
      _iq Kp = _IQ(0.05*Lhf*USER_IQ_FULL_SCALE_CURRENT_A/(USER_CTRL_PERIOD_sec*USER_IQ_FULL_SCALE_VOLTAGE_V));
      _iq Ki = _IQ(RhfoverLhf*USER_CTRL_PERIOD_sec);
      _iq Kp_spd = _IQ(0.005*USER_IQ_FULL_SCALE_FREQ_Hz*USER_MOTOR_MAX_CURRENT/USER_IQ_FULL_SCALE_CURRENT_A);

      // set Rhf/Lhf
      CTRL_setRoverL(handle,RhfoverLhf);

      // set the controller proportional gains
      CTRL_setKp(handle,CTRL_Type_PID_Id,Kp);
      CTRL_setKp(handle,CTRL_Type_PID_Iq,Kp);

      // set the Id controller gains
      CTRL_setKi(handle,CTRL_Type_PID_Id,Ki);
      PID_setKi(obj->pidHandle_Id,Ki);

      // set the Iq controller gains
      CTRL_setKi(handle,CTRL_Type_PID_Iq,Ki);
      PID_setKi(obj->pidHandle_Iq,Ki);

      // set speed gains
      PID_setKp(obj->pidHandle_spd,Kp_spd);
    }
  else if(EstState == EST_State_RatedFlux)
    {
      _iq Ki_spd = _IQ(0.5*USER_IQ_FULL_SCALE_FREQ_Hz*USER_CTRL_PERIOD_sec*USER_MOTOR_MAX_CURRENT/USER_IQ_FULL_SCALE_CURRENT_A);

      // Set Ki on closing the feedback loop
      PID_setKi(obj->pidHandle_spd,Ki_spd);
    }
  else if(EstState == EST_State_RampDown)
    {
      _iq Kp_spd = _IQ(0.02*USER_IQ_FULL_SCALE_FREQ_Hz*USER_MOTOR_MAX_CURRENT/USER_IQ_FULL_SCALE_CURRENT_A);
      _iq Ki_spd = _IQ(2.0*USER_IQ_FULL_SCALE_FREQ_Hz*USER_CTRL_PERIOD_sec*USER_MOTOR_MAX_CURRENT/USER_IQ_FULL_SCALE_CURRENT_A);

      // Set Kp and Ki of the speed controller
      PID_setKp(obj->pidHandle_spd,Kp_spd);
      PID_setKi(obj->pidHandle_spd,Ki_spd);

      TRAJ_setTargetValue(obj->trajHandle_spdMax,_IQ(USER_MOTOR_RES_EST_CURRENT/USER_IQ_FULL_SCALE_CURRENT_A));
    }

  return;
} // end of recalcKpKiPmsm() function


void CTRL_calcMax_Ls_qFmt(CTRL_Handle handle, uint_least8_t *pLs_qFmt)
{
  CTRL_Obj *obj = (CTRL_Obj *)handle;

  if((EST_isMotorIdentified(obj->estHandle) == false) && (EST_getState(obj->estHandle) == EST_State_Rs))
    {
      float_t Lhf = CTRL_getLhf(handle);
	  float_t fullScaleInductance = USER_IQ_FULL_SCALE_VOLTAGE_V/(USER_IQ_FULL_SCALE_CURRENT_A*USER_VOLTAGE_FILTER_POLE_rps);
	  float_t Ls_coarse_max = _IQ30toF(EST_getLs_coarse_max_pu(obj->estHandle));
	  int_least8_t lShift = ceil(log((Lhf/20.0)/(Ls_coarse_max*fullScaleInductance))/log(2.0));

	  *pLs_qFmt = 30 - lShift;
    }

  return;
} // end of CTRL_calcMax_Ls_qFmt() function


void recalcKpKi(CTRL_Handle handle)
{
  CTRL_Obj *obj = (CTRL_Obj *)handle;
  EST_State_e EstState = EST_getState(obj->estHandle);

  if((EST_isMotorIdentified(obj->estHandle) == false) && (EstState == EST_State_Rs))
    {
      float_t Lhf = CTRL_getLhf(handle);
      float_t Rhf = CTRL_getRhf(handle);
      float_t RhfoverLhf = Rhf/Lhf;
      _iq Kp = _IQ(0.25*Lhf*USER_IQ_FULL_SCALE_CURRENT_A/(USER_CTRL_PERIOD_sec*USER_IQ_FULL_SCALE_VOLTAGE_V));
      _iq Ki = _IQ(RhfoverLhf*USER_CTRL_PERIOD_sec);

      // set Rhf/Lhf
      CTRL_setRoverL(handle,RhfoverLhf);

      // set the controller proportional gains
      CTRL_setKp(handle,CTRL_Type_PID_Id,Kp);
      CTRL_setKp(handle,CTRL_Type_PID_Iq,Kp);

      // set the Id controller gains
      CTRL_setKi(handle,CTRL_Type_PID_Id,Ki);
      PID_setKi(obj->pidHandle_Id,Ki);

      // set the Iq controller gains
      CTRL_setKi(handle,CTRL_Type_PID_Iq,Ki);
      PID_setKi(obj->pidHandle_Iq,Ki);
    }

  return;
} // end of recalcKpKi() function


void setFeLimitZero(CTRL_Handle handle)
{
  CTRL_Obj *obj = (CTRL_Obj *)handle;
  EST_State_e EstState = EST_getState(obj->estHandle);

  _iq fe_neg_max_pu;
  _iq fe_pos_min_pu;

  if((EST_isMotorIdentified(obj->estHandle) == false) && (CTRL_getMotorType(handle) == MOTOR_Type_Induction))
    {
	  fe_neg_max_pu = _IQ30(0.0);

	  fe_pos_min_pu = _IQ30(0.0);
    }
  else
    {
	  fe_neg_max_pu = _IQ30(-USER_ZEROSPEEDLIMIT);

	  fe_pos_min_pu = _IQ30(USER_ZEROSPEEDLIMIT);
    }

  EST_setFe_neg_max_pu(obj->estHandle, fe_neg_max_pu);

  EST_setFe_pos_min_pu(obj->estHandle, fe_pos_min_pu);

  return;
} // end of setFeLimitZero() function


void acim_Dir_qFmtCalc(CTRL_Handle handle)
{
  CTRL_Obj *obj = (CTRL_Obj *)handle;
  EST_State_e EstState = EST_getState(obj->estHandle);

  if(EstState == EST_State_IdRated)
    {
      EST_setDir_qFmt(obj->estHandle, EST_computeDirection_qFmt(obj->estHandle, 0.7));
    }

  return;
} // end of acim_Dir_qFmtCalc() function


//@} //defgroup
// end of file

/* --COPYRIGHT--,BSD
 * Copyright (c) 2015, Texas Instruments Incorporated
 * All rights reserved.
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions
 * are met:
 *
 * *  Redistributions of source code must retain the above copyright
 *    notice, this list of conditions and the following disclaimer.
 *
 * *  Redistributions in binary form must reproduce the above copyright
 *    notice, this list of conditions and the following disclaimer in the
 *    documentation and/or other materials provided with the distribution.
 *
 * *  Neither the name of Texas Instruments Incorporated nor the names of
 *    its contributors may be used to endorse or promote products derived
 *    from this software without specific prior written permission.
 *
 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
 * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
 * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
 * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
 * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
 * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
 * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS;
 * OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
 * WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR
 * OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
 * EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
 * --/COPYRIGHT--*/
//! \file  sw/modules/hal/boards/boostxldrv8353/f28x/f2802xF/src/hal.c
//! \brief Contains the various functions related to the HAL object (everything outside the CTRL system) 
//!
//! (C) Copyright 2015, Texas Instruments, Inc.


// **************************************************************************
// the includes

// drivers

// modules

// platforms
#include "hal.h"
#include "user.h"
#include "hal_obj.h"

#ifdef FLASH
#pragma CODE_SECTION(HAL_setupFlash,"ramfuncs");
#endif

// **************************************************************************
// the defines

#define US_TO_CNT(A) ((((long double) A * (long double)USER_SYSTEM_FREQ_MHz) - 9.0L) / 5.0L)

// **************************************************************************
// the globals

#ifdef F2802xF
#pragma DATA_SECTION(hal,"rom_accessed_data");
#endif
HAL_Obj hal;


// **************************************************************************
// the functions

void HAL_cal(HAL_Handle handle)
{
  HAL_Obj *obj = (HAL_Obj *)handle;


  // enable the ADC clock
  CLK_enableAdcClock(obj->clkHandle);


  // Run the Device_cal() function
  // This function copies the ADC and oscillator calibration values from TI reserved
  // OTP into the appropriate trim registers
  // This boot ROM automatically calls this function to calibrate the interal 
  // oscillators and ADC with device specific calibration data.
  // If the boot ROM is bypassed by Code Composer Studio during the development process,
  // then the calibration must be initialized by the application
  ENABLE_PROTECTED_REGISTER_WRITE_MODE;
  (*Device_cal)();
  DISABLE_PROTECTED_REGISTER_WRITE_MODE;

  // run offsets calibration in user's memory
  HAL_AdcOffsetSelfCal(handle);

  // run oscillator compensation
  HAL_OscTempComp(handle);

  // disable the ADC clock
  CLK_disableAdcClock(obj->clkHandle);

  return;
} // end of HAL_cal() function


void HAL_OscTempComp(HAL_Handle handle)
{
  HAL_Obj *obj = (HAL_Obj *)handle;
  uint16_t Temperature;

  // disable the ADCs
  ADC_disable(obj->adcHandle);

  // power up the bandgap circuit
  ADC_enableBandGap(obj->adcHandle);

  // set the ADC voltage reference source to internal
  ADC_setVoltRefSrc(obj->adcHandle,ADC_VoltageRefSrc_Int);

  // enable the ADC reference buffers
  ADC_enableRefBuffers(obj->adcHandle);

  // Set main clock scaling factor (max45MHz clock for the ADC module)
  ADC_setDivideSelect(obj->adcHandle,ADC_DivideSelect_ClkIn_by_2);

  // power up the ADCs
  ADC_powerUp(obj->adcHandle);

  // enable the ADCs
  ADC_enable(obj->adcHandle);

  // enable non-overlap mode
  ADC_enableNoOverlapMode(obj->adcHandle);

  // connect channel A5 internally to the temperature sensor
  ADC_setTempSensorSrc(obj->adcHandle, ADC_TempSensorSrc_Int);

  // set SOC0 channel select to ADCINA5
  ADC_setSocChanNumber(obj->adcHandle, ADC_SocNumber_0, ADC_SocChanNumber_A5);

  // set SOC0 acquisition period to 26 ADCCLK
  ADC_setSocSampleDelay(obj->adcHandle, ADC_SocNumber_0, ADC_SocSampleDelay_64_cycles);

  // connect ADCINT1 to EOC0
  ADC_setIntSrc(obj->adcHandle, ADC_IntNumber_1, ADC_IntSrc_EOC0);

  // clear ADCINT1 flag
  ADC_clearIntFlag(obj->adcHandle, ADC_IntNumber_1);

  // enable ADCINT1
  ADC_enableInt(obj->adcHandle, ADC_IntNumber_1);

  // force start of conversion on SOC0
  ADC_setSocFrc(obj->adcHandle, ADC_SocFrc_0);

  // wait for end of conversion
  while (ADC_getIntFlag(obj->adcHandle, ADC_IntNumber_1) == 0){}

  // clear ADCINT1 flag
  ADC_clearIntFlag(obj->adcHandle, ADC_IntNumber_1);

  Temperature = ADC_readResult(obj->adcHandle, ADC_ResultNumber_0);

  HAL_osc1Comp(handle, Temperature);

  HAL_osc2Comp(handle, Temperature);

  return;
} // end of HAL_OscTempComp() function


void HAL_osc1Comp(HAL_Handle handle, const int16_t sensorSample)
{
	int16_t compOscFineTrim;
	HAL_Obj *obj = (HAL_Obj *)handle;

	ENABLE_PROTECTED_REGISTER_WRITE_MODE;

    compOscFineTrim = ((sensorSample - getRefTempOffset())*(int32_t)getOsc1FineTrimSlope()
                      + OSC_POSTRIM_OFF + FP_ROUND )/FP_SCALE + getOsc1FineTrimOffset() - OSC_POSTRIM;

    if(compOscFineTrim > 31)
      {
        compOscFineTrim = 31;
      }
	else if(compOscFineTrim < -31)
      {
        compOscFineTrim = -31;
      }

    OSC_setTrim(obj->oscHandle, OSC_Number_1, HAL_getOscTrimValue(getOsc1CoarseTrim(), compOscFineTrim));

    DISABLE_PROTECTED_REGISTER_WRITE_MODE;

    return;
} // end of HAL_osc1Comp() function


void HAL_osc2Comp(HAL_Handle handle, const int16_t sensorSample)
{
	int16_t compOscFineTrim;
	HAL_Obj *obj = (HAL_Obj *)handle;

	ENABLE_PROTECTED_REGISTER_WRITE_MODE;

    compOscFineTrim = ((sensorSample - getRefTempOffset())*(int32_t)getOsc2FineTrimSlope()
                      + OSC_POSTRIM_OFF + FP_ROUND )/FP_SCALE + getOsc2FineTrimOffset() - OSC_POSTRIM;

    if(compOscFineTrim > 31)
      {
        compOscFineTrim = 31;
      }
	else if(compOscFineTrim < -31)
      {
        compOscFineTrim = -31;
      }

    OSC_setTrim(obj->oscHandle, OSC_Number_2, HAL_getOscTrimValue(getOsc2CoarseTrim(), compOscFineTrim));

    DISABLE_PROTECTED_REGISTER_WRITE_MODE;

    return;
} // end of HAL_osc2Comp() function


uint16_t HAL_getOscTrimValue(int16_t coarse, int16_t fine)
{
  uint16_t regValue = 0;

  if(fine < 0)
    {
      regValue = ((-fine) | 0x20) << 9;
    }
  else
    {
      regValue = fine << 9;
    }

  if(coarse < 0)
    {
      regValue |= ((-coarse) | 0x80);
    }
  else
    {
      regValue |= coarse;
    }

  return regValue;
} // end of HAL_getOscTrimValue() function


void HAL_AdcOffsetSelfCal(HAL_Handle handle)
{
  HAL_Obj *obj = (HAL_Obj *)handle;
  uint16_t AdcConvMean;

  // disable the ADCs
  ADC_disable(obj->adcHandle);

  // power up the bandgap circuit
  ADC_enableBandGap(obj->adcHandle);

  // set the ADC voltage reference source to internal
  ADC_setVoltRefSrc(obj->adcHandle,ADC_VoltageRefSrc_Int);

  // enable the ADC reference buffers
  ADC_enableRefBuffers(obj->adcHandle);

  // power up the ADCs
  ADC_powerUp(obj->adcHandle);

  // enable the ADCs
  ADC_enable(obj->adcHandle);

  //Select VREFLO internal connection on B5
  ADC_enableVoltRefLoConv(obj->adcHandle);

  //Select channel B5 for all SOC
  HAL_AdcCalChanSelect(handle, ADC_SocChanNumber_B5);

  //Apply artificial offset (+80) to account for a negative offset that may reside in the ADC core
  ADC_setOffTrim(obj->adcHandle, 80);

  //Capture ADC conversion on VREFLO
  AdcConvMean = HAL_AdcCalConversion(handle);

  //Set offtrim register with new value (i.e remove artical offset (+80) and create a two's compliment of the offset error)
  ADC_setOffTrim(obj->adcHandle, 80 - AdcConvMean);

  //Select external ADCIN5 input pin on B5
  ADC_disableVoltRefLoConv(obj->adcHandle);

  return;
} // end of HAL_AdcOffsetSelfCal() function


void HAL_AdcCalChanSelect(HAL_Handle handle, const ADC_SocChanNumber_e chanNumber)
{
  HAL_Obj *obj = (HAL_Obj *)handle;

  ADC_setSocChanNumber(obj->adcHandle,ADC_SocNumber_0,chanNumber);
  ADC_setSocChanNumber(obj->adcHandle,ADC_SocNumber_1,chanNumber);
  ADC_setSocChanNumber(obj->adcHandle,ADC_SocNumber_2,chanNumber);
  ADC_setSocChanNumber(obj->adcHandle,ADC_SocNumber_3,chanNumber);
  ADC_setSocChanNumber(obj->adcHandle,ADC_SocNumber_4,chanNumber);
  ADC_setSocChanNumber(obj->adcHandle,ADC_SocNumber_5,chanNumber);
  ADC_setSocChanNumber(obj->adcHandle,ADC_SocNumber_6,chanNumber);
  ADC_setSocChanNumber(obj->adcHandle,ADC_SocNumber_7,chanNumber);
  ADC_setSocChanNumber(obj->adcHandle,ADC_SocNumber_8,chanNumber);
  ADC_setSocChanNumber(obj->adcHandle,ADC_SocNumber_9,chanNumber);
  ADC_setSocChanNumber(obj->adcHandle,ADC_SocNumber_10,chanNumber);
  ADC_setSocChanNumber(obj->adcHandle,ADC_SocNumber_11,chanNumber);
  ADC_setSocChanNumber(obj->adcHandle,ADC_SocNumber_12,chanNumber);
  ADC_setSocChanNumber(obj->adcHandle,ADC_SocNumber_13,chanNumber);
  ADC_setSocChanNumber(obj->adcHandle,ADC_SocNumber_14,chanNumber);
  ADC_setSocChanNumber(obj->adcHandle,ADC_SocNumber_15,chanNumber);

  return;
} // end of HAL_AdcCalChanSelect() function


uint16_t HAL_AdcCalConversion(HAL_Handle handle)
{
  HAL_Obj *obj = (HAL_Obj *)handle;
  uint16_t index, SampleSize, Mean;
  uint32_t Sum;
  ADC_SocSampleDelay_e ACQPS_Value;

  index       = 0;     //initialize index to 0
  SampleSize  = 256;   //set sample size to 256 (**NOTE: Sample size must be multiples of 2^x where is an integer >= 4)
  Sum         = 0;     //set sum to 0
  Mean        = 999;   //initialize mean to known value

  //Set the ADC sample window to the desired value (Sample window = ACQPS + 1)
  ACQPS_Value = ADC_SocSampleDelay_7_cycles;

  ADC_setSocSampleDelay(obj->adcHandle,ADC_SocNumber_0,ACQPS_Value);
  ADC_setSocSampleDelay(obj->adcHandle,ADC_SocNumber_1,ACQPS_Value);
  ADC_setSocSampleDelay(obj->adcHandle,ADC_SocNumber_2,ACQPS_Value);
  ADC_setSocSampleDelay(obj->adcHandle,ADC_SocNumber_3,ACQPS_Value);
  ADC_setSocSampleDelay(obj->adcHandle,ADC_SocNumber_4,ACQPS_Value);
  ADC_setSocSampleDelay(obj->adcHandle,ADC_SocNumber_5,ACQPS_Value);
  ADC_setSocSampleDelay(obj->adcHandle,ADC_SocNumber_6,ACQPS_Value);
  ADC_setSocSampleDelay(obj->adcHandle,ADC_SocNumber_7,ACQPS_Value);
  ADC_setSocSampleDelay(obj->adcHandle,ADC_SocNumber_8,ACQPS_Value);
  ADC_setSocSampleDelay(obj->adcHandle,ADC_SocNumber_9,ACQPS_Value);
  ADC_setSocSampleDelay(obj->adcHandle,ADC_SocNumber_10,ACQPS_Value);
  ADC_setSocSampleDelay(obj->adcHandle,ADC_SocNumber_11,ACQPS_Value);
  ADC_setSocSampleDelay(obj->adcHandle,ADC_SocNumber_12,ACQPS_Value);
  ADC_setSocSampleDelay(obj->adcHandle,ADC_SocNumber_13,ACQPS_Value);
  ADC_setSocSampleDelay(obj->adcHandle,ADC_SocNumber_14,ACQPS_Value);
  ADC_setSocSampleDelay(obj->adcHandle,ADC_SocNumber_15,ACQPS_Value);

  // Enabled ADCINT1 and ADCINT2
  ADC_enableInt(obj->adcHandle, ADC_IntNumber_1);
  ADC_enableInt(obj->adcHandle, ADC_IntNumber_2);

  // Disable continuous sampling for ADCINT1 and ADCINT2
  ADC_setIntMode(obj->adcHandle, ADC_IntNumber_1, ADC_IntMode_EOC);
  ADC_setIntMode(obj->adcHandle, ADC_IntNumber_2, ADC_IntMode_EOC);

  //ADCINTs trigger at end of conversion
  ADC_setIntPulseGenMode(obj->adcHandle, ADC_IntPulseGenMode_Prior);

  // Setup ADCINT1 and ADCINT2 trigger source
  ADC_setIntSrc(obj->adcHandle, ADC_IntNumber_1, ADC_IntSrc_EOC6);
  ADC_setIntSrc(obj->adcHandle, ADC_IntNumber_2, ADC_IntSrc_EOC14);

  // Setup each SOC's ADCINT trigger source
  ADC_setupSocTrigSrc(obj->adcHandle, ADC_SocNumber_0, ADC_Int2TriggersSOC);
  ADC_setupSocTrigSrc(obj->adcHandle, ADC_SocNumber_1, ADC_Int2TriggersSOC);
  ADC_setupSocTrigSrc(obj->adcHandle, ADC_SocNumber_2, ADC_Int2TriggersSOC);
  ADC_setupSocTrigSrc(obj->adcHandle, ADC_SocNumber_3, ADC_Int2TriggersSOC);
  ADC_setupSocTrigSrc(obj->adcHandle, ADC_SocNumber_4, ADC_Int2TriggersSOC);
  ADC_setupSocTrigSrc(obj->adcHandle, ADC_SocNumber_5, ADC_Int2TriggersSOC);
  ADC_setupSocTrigSrc(obj->adcHandle, ADC_SocNumber_6, ADC_Int2TriggersSOC);
  ADC_setupSocTrigSrc(obj->adcHandle, ADC_SocNumber_7, ADC_Int2TriggersSOC);
  ADC_setupSocTrigSrc(obj->adcHandle, ADC_SocNumber_8, ADC_Int1TriggersSOC);
  ADC_setupSocTrigSrc(obj->adcHandle, ADC_SocNumber_9, ADC_Int1TriggersSOC);
  ADC_setupSocTrigSrc(obj->adcHandle, ADC_SocNumber_10, ADC_Int1TriggersSOC);
  ADC_setupSocTrigSrc(obj->adcHandle, ADC_SocNumber_11, ADC_Int1TriggersSOC);
  ADC_setupSocTrigSrc(obj->adcHandle, ADC_SocNumber_12, ADC_Int1TriggersSOC);
  ADC_setupSocTrigSrc(obj->adcHandle, ADC_SocNumber_13, ADC_Int1TriggersSOC);
  ADC_setupSocTrigSrc(obj->adcHandle, ADC_SocNumber_14, ADC_Int1TriggersSOC);
  ADC_setupSocTrigSrc(obj->adcHandle, ADC_SocNumber_15, ADC_Int1TriggersSOC);

  // Delay before converting ADC channels
  usDelay(US_TO_CNT(ADC_DELAY_usec));

  ADC_setSocFrcWord(obj->adcHandle, 0x00FF);

  while( index < SampleSize )
    {
      //Wait for ADCINT1 to trigger, then add ADCRESULT0-7 registers to sum
      while (ADC_getIntFlag(obj->adcHandle, ADC_IntNumber_1) == 0){}

      //Must clear ADCINT1 flag since INT1CONT = 0
      ADC_clearIntFlag(obj->adcHandle, ADC_IntNumber_1);

      Sum += ADC_readResult(obj->adcHandle, ADC_ResultNumber_0);
      Sum += ADC_readResult(obj->adcHandle, ADC_ResultNumber_1);
      Sum += ADC_readResult(obj->adcHandle, ADC_ResultNumber_2);
      Sum += ADC_readResult(obj->adcHandle, ADC_ResultNumber_3);
      Sum += ADC_readResult(obj->adcHandle, ADC_ResultNumber_4);
      Sum += ADC_readResult(obj->adcHandle, ADC_ResultNumber_5);
      Sum += ADC_readResult(obj->adcHandle, ADC_ResultNumber_6);
      Sum += ADC_readResult(obj->adcHandle, ADC_ResultNumber_7);

      //Wait for ADCINT2 to trigger, then add ADCRESULT8-15 registers to sum
      while (ADC_getIntFlag(obj->adcHandle, ADC_IntNumber_2) == 0){}

      //Must clear ADCINT2 flag since INT2CONT = 0
      ADC_clearIntFlag(obj->adcHandle, ADC_IntNumber_2);

      Sum += ADC_readResult(obj->adcHandle, ADC_ResultNumber_8);
      Sum += ADC_readResult(obj->adcHandle, ADC_ResultNumber_9);
      Sum += ADC_readResult(obj->adcHandle, ADC_ResultNumber_10);
      Sum += ADC_readResult(obj->adcHandle, ADC_ResultNumber_11);
      Sum += ADC_readResult(obj->adcHandle, ADC_ResultNumber_12);
      Sum += ADC_readResult(obj->adcHandle, ADC_ResultNumber_13);
      Sum += ADC_readResult(obj->adcHandle, ADC_ResultNumber_14);
      Sum += ADC_readResult(obj->adcHandle, ADC_ResultNumber_15);

      index+=16;

  } // end data collection

  //Disable ADCINT1 and ADCINT2 to STOP the ping-pong sampling
  ADC_disableInt(obj->adcHandle, ADC_IntNumber_1);
  ADC_disableInt(obj->adcHandle, ADC_IntNumber_2);

  //Calculate average ADC sample value
  Mean = Sum / SampleSize;

  // Clear start of conversion trigger
  ADC_setupSocTrigSrc(obj->adcHandle, ADC_SocNumber_0, ADC_NoIntTriggersSOC);
  ADC_setupSocTrigSrc(obj->adcHandle, ADC_SocNumber_1, ADC_NoIntTriggersSOC);
  ADC_setupSocTrigSrc(obj->adcHandle, ADC_SocNumber_2, ADC_NoIntTriggersSOC);
  ADC_setupSocTrigSrc(obj->adcHandle, ADC_SocNumber_3, ADC_NoIntTriggersSOC);
  ADC_setupSocTrigSrc(obj->adcHandle, ADC_SocNumber_4, ADC_NoIntTriggersSOC);
  ADC_setupSocTrigSrc(obj->adcHandle, ADC_SocNumber_5, ADC_NoIntTriggersSOC);
  ADC_setupSocTrigSrc(obj->adcHandle, ADC_SocNumber_6, ADC_NoIntTriggersSOC);
  ADC_setupSocTrigSrc(obj->adcHandle, ADC_SocNumber_7, ADC_NoIntTriggersSOC);
  ADC_setupSocTrigSrc(obj->adcHandle, ADC_SocNumber_8, ADC_NoIntTriggersSOC);
  ADC_setupSocTrigSrc(obj->adcHandle, ADC_SocNumber_9, ADC_NoIntTriggersSOC);
  ADC_setupSocTrigSrc(obj->adcHandle, ADC_SocNumber_10, ADC_NoIntTriggersSOC);
  ADC_setupSocTrigSrc(obj->adcHandle, ADC_SocNumber_11, ADC_NoIntTriggersSOC);
  ADC_setupSocTrigSrc(obj->adcHandle, ADC_SocNumber_12, ADC_NoIntTriggersSOC);
  ADC_setupSocTrigSrc(obj->adcHandle, ADC_SocNumber_13, ADC_NoIntTriggersSOC);
  ADC_setupSocTrigSrc(obj->adcHandle, ADC_SocNumber_14, ADC_NoIntTriggersSOC);
  ADC_setupSocTrigSrc(obj->adcHandle, ADC_SocNumber_15, ADC_NoIntTriggersSOC);

  //return the average
  return(Mean);
} // end of HAL_AdcCalConversion() function


void HAL_disableWdog(HAL_Handle halHandle)
{
  HAL_Obj *hal = (HAL_Obj *)halHandle;


  WDOG_disable(hal->wdogHandle);


  return;
} // end of HAL_disableWdog() function


void HAL_disableGlobalInts(HAL_Handle handle)
{
  HAL_Obj *obj = (HAL_Obj *)handle;


  CPU_disableGlobalInts(obj->cpuHandle);

  return;
} // end of HAL_disableGlobalInts() function


void HAL_enableAdcInts(HAL_Handle handle)
{
  HAL_Obj *obj = (HAL_Obj *)handle;


  // enable the PIE interrupts associated with the ADC interrupts
  PIE_enableAdcInt(obj->pieHandle,ADC_IntNumber_1);


  // enable the ADC interrupts
  ADC_enableInt(obj->adcHandle,ADC_IntNumber_1);


  // enable the cpu interrupt for ADC interrupts
  CPU_enableInt(obj->cpuHandle,CPU_IntNumber_10);

  return;
} // end of HAL_enableAdcInts() function


void HAL_enableDebugInt(HAL_Handle handle)
{
  HAL_Obj *obj = (HAL_Obj *)handle;


  CPU_enableDebugInt(obj->cpuHandle);

  return;
} // end of HAL_enableDebugInt() function


void HAL_enableDrv(HAL_Handle handle)
{
  HAL_Obj *obj = (HAL_Obj *)handle;

  DRV8353_enable(obj->drv8353Handle);

  return;
}  // end of HAL_enableDrv() function


void HAL_enableGlobalInts(HAL_Handle handle)
{
  HAL_Obj *obj = (HAL_Obj *)handle;


  CPU_enableGlobalInts(obj->cpuHandle);

  return;
} // end of HAL_enableGlobalInts() function


void HAL_enablePwmInt(HAL_Handle handle)
{
  HAL_Obj *obj = (HAL_Obj *)handle;


  PIE_enablePwmInt(obj->pieHandle,PWM_Number_1);


  // enable the interrupt
  PWM_enableInt(obj->pwmHandle[PWM_Number_1]);


  // enable the cpu interrupt for EPWM1_INT
  CPU_enableInt(obj->cpuHandle,CPU_IntNumber_3);

  return;
} // end of HAL_enablePwmInt() function


void HAL_setupFaults(HAL_Handle handle)
{
  HAL_Obj *obj = (HAL_Obj *)handle;
  uint_least8_t cnt;

  // Configure Trip Mechanism for the Motor control software
  // -Cycle by cycle trip on CPU halt
  // -One shot fault trip zone
  // These trips need to be repeated for EPWM1 ,2 & 3

  for(cnt=0;cnt<3;cnt++)
    {
      PWM_enableTripZoneSrc(obj->pwmHandle[cnt],PWM_TripZoneSrc_CycleByCycle_TZ6_NOT);

//    PWM_enableTripZoneSrc(obj->pwmHandle[cnt],PWM_TripZoneSrc_CycleByCycle_TZ2_NOT);

      // What do we want the OST/CBC events to do?
      // TZA events can force EPWMxA
      // TZB events can force EPWMxB

      PWM_setTripZoneState_TZA(obj->pwmHandle[cnt],PWM_TripZoneState_EPWM_Low);
      PWM_setTripZoneState_TZB(obj->pwmHandle[cnt],PWM_TripZoneState_EPWM_Low);
    }

  return;
} // end of HAL_setupFaults() function


HAL_Handle HAL_init(void *pMemory,const size_t numBytes)
{
  uint_least8_t cnt;
  HAL_Handle handle;
  HAL_Obj *obj;


  if(numBytes < sizeof(HAL_Obj))
    return((HAL_Handle)NULL);


  // assign the handle
  handle = (HAL_Handle)pMemory;


  // assign the object
  obj = (HAL_Obj *)handle;


  // initialize the watchdog driver
  obj->wdogHandle = WDOG_init((void *)WDOG_BASE_ADDR,sizeof(WDOG_Obj));


  // disable watchdog
  HAL_disableWdog(handle);


  // initialize the ADC
  obj->adcHandle = ADC_init((void *)ADC_BASE_ADDR,sizeof(ADC_Obj));


  // initialize the clock handle
  obj->clkHandle = CLK_init((void *)CLK_BASE_ADDR,sizeof(CLK_Obj));


  // initialize the CPU handle
  obj->cpuHandle = CPU_init(&cpu,sizeof(cpu));


  // initialize the FLASH handle
  obj->flashHandle = FLASH_init((void *)FLASH_BASE_ADDR,sizeof(FLASH_Obj));


  // initialize the GPIO handle
  obj->gpioHandle = GPIO_init((void *)GPIO_BASE_ADDR,sizeof(GPIO_Obj));


  // initialize the current offset estimator handles
  for(cnt=0;cnt<USER_NUM_CURRENT_SENSORS;cnt++)
    {
      obj->offsetHandle_I[cnt] = OFFSET_init(&obj->offset_I[cnt],sizeof(obj->offset_I[cnt]));
    }


  // initialize the voltage offset estimator handles
  for(cnt=0;cnt<USER_NUM_VOLTAGE_SENSORS;cnt++)
    {
      obj->offsetHandle_V[cnt] = OFFSET_init(&obj->offset_V[cnt],sizeof(obj->offset_V[cnt]));
    }


  // initialize the oscillator handle
  obj->oscHandle = OSC_init((void *)OSC_BASE_ADDR,sizeof(OSC_Obj));


  // initialize the PIE handle
  obj->pieHandle = PIE_init((void *)PIE_BASE_ADDR,sizeof(PIE_Obj));


  // initialize the PLL handle
  obj->pllHandle = PLL_init((void *)PLL_BASE_ADDR,sizeof(PLL_Obj));

#ifdef DRV8353_SPI
  // initialize the SPIA handle
  if(gDeviceVariant)
	  obj->spiAHandle = SPI_init((void *)SPIA_BASE_ADDR,sizeof(SPI_Obj));
#endif

  // initialize PWM handle
  obj->pwmHandle[0] = PWM_init((void *)PWM_ePWM1_BASE_ADDR,sizeof(PWM_Obj));
  obj->pwmHandle[1] = PWM_init((void *)PWM_ePWM2_BASE_ADDR,sizeof(PWM_Obj));
  obj->pwmHandle[2] = PWM_init((void *)PWM_ePWM3_BASE_ADDR,sizeof(PWM_Obj));


  // initialize power handle
  obj->pwrHandle = PWR_init((void *)PWR_BASE_ADDR,sizeof(PWR_Obj));


  // initialize timer drivers
  obj->timerHandle[0] = TIMER_init((void *)TIMER0_BASE_ADDR,sizeof(TIMER_Obj));
  obj->timerHandle[1] = TIMER_init((void *)TIMER1_BASE_ADDR,sizeof(TIMER_Obj));
  obj->timerHandle[2] = TIMER_init((void *)TIMER2_BASE_ADDR,sizeof(TIMER_Obj));


  // initialize drv8353 interface
  obj->drv8353Handle = DRV8353_init(&obj->drv8353,sizeof(obj->drv8353));

  return(handle);
} // end of HAL_init() function


void HAL_setParams(HAL_Handle handle,const USER_Params *pUserParams)
{
  uint_least8_t cnt;
  HAL_Obj *obj = (HAL_Obj *)handle;
  _iq beta_lp_pu = _IQ(pUserParams->offsetPole_rps/(float_t)pUserParams->ctrlFreq_Hz);


  HAL_setNumCurrentSensors(handle,pUserParams->numCurrentSensors);
  HAL_setNumVoltageSensors(handle,pUserParams->numVoltageSensors);


  for(cnt=0;cnt<HAL_getNumCurrentSensors(handle);cnt++)
    {
      HAL_setOffsetBeta_lp_pu(handle,HAL_SensorType_Current,cnt,beta_lp_pu);
      HAL_setOffsetInitCond(handle,HAL_SensorType_Current,cnt,_IQ(0.0));
      HAL_setOffsetValue(handle,HAL_SensorType_Current,cnt,_IQ(0.0));
    }


  for(cnt=0;cnt<HAL_getNumVoltageSensors(handle);cnt++)
    {
      HAL_setOffsetBeta_lp_pu(handle,HAL_SensorType_Voltage,cnt,beta_lp_pu);
      HAL_setOffsetInitCond(handle,HAL_SensorType_Voltage,cnt,_IQ(0.0));
      HAL_setOffsetValue(handle,HAL_SensorType_Voltage,cnt,_IQ(0.0));
    }


  // disable global interrupts
  CPU_disableGlobalInts(obj->cpuHandle);


  // disable cpu interrupts
  CPU_disableInts(obj->cpuHandle);


  // clear cpu interrupt flags
  CPU_clearIntFlags(obj->cpuHandle);


  // setup the clocks
  HAL_setupClks(handle);


  // Setup the PLL
  HAL_setupPll(handle,PLL_ClkFreq_60_MHz);


  // setup the PIE
  HAL_setupPie(handle);


  // run the device calibration
  HAL_cal(handle);


  // setup the peripheral clocks
  HAL_setupPeripheralClks(handle);


  // setup the GPIOs
  HAL_setupGpios(handle);


  // setup the flash
  HAL_setupFlash(handle);


  // setup the ADCs
  HAL_setupAdcs(handle);


  // setup the PWMs
  HAL_setupPwms(handle,
                (float_t)pUserParams->systemFreq_MHz,
                pUserParams->pwmPeriod_usec,
                USER_NUM_PWM_TICKS_PER_ISR_TICK);

#ifdef DRV8353_SPI
  // setup the spiA
  if(gDeviceVariant)
	  HAL_setupSpiA(handle);
#endif

  // setup the timers
  HAL_setupTimers(handle,
                  (float_t)pUserParams->systemFreq_MHz);


  // setup the drv8353 interface
  HAL_setupGate(handle);


  // set the default current bias
 {
   uint_least8_t cnt;
   _iq bias = _IQ12mpy(ADC_dataBias,_IQ(pUserParams->current_sf));
   
   for(cnt=0;cnt<HAL_getNumCurrentSensors(handle);cnt++)
     {
       HAL_setBias(handle,HAL_SensorType_Current,cnt,bias);
     }
 }


  //  set the current scale factor
 {
   _iq current_sf = _IQ(pUserParams->current_sf);

  HAL_setCurrentScaleFactor(handle,current_sf);
 }


  // set the default voltage bias
 {
   uint_least8_t cnt;
   _iq bias = _IQ(0.0);
   
   for(cnt=0;cnt<HAL_getNumVoltageSensors(handle);cnt++)
     {
       HAL_setBias(handle,HAL_SensorType_Voltage,cnt,bias);
     }
 }


  //  set the voltage scale factor
 {
   _iq voltage_sf = _IQ(pUserParams->voltage_sf);

  HAL_setVoltageScaleFactor(handle,voltage_sf);
 }

 return;
} // end of HAL_setParams() function


void HAL_setupAdcs(HAL_Handle handle)
{
  HAL_Obj *obj = (HAL_Obj *)handle;


  // disable the ADCs
  ADC_disable(obj->adcHandle);


  // power up the bandgap circuit
  ADC_enableBandGap(obj->adcHandle);


  // set the ADC voltage reference source to internal 
  ADC_setVoltRefSrc(obj->adcHandle,ADC_VoltageRefSrc_Int);


  // enable the ADC reference buffers
  ADC_enableRefBuffers(obj->adcHandle);


  // Set main clock scaling factor (max45MHz clock for the ADC module)
  ADC_setDivideSelect(obj->adcHandle,ADC_DivideSelect_ClkIn_by_2);

  // power up the ADCs
  ADC_powerUp(obj->adcHandle);


  // enable the ADCs
  ADC_enable(obj->adcHandle);


  // set the ADC interrupt pulse generation to prior
  ADC_setIntPulseGenMode(obj->adcHandle,ADC_IntPulseGenMode_Prior);


  // set the temperature sensor source to external
  ADC_setTempSensorSrc(obj->adcHandle,ADC_TempSensorSrc_Ext);


  // configure the interrupt sources
  ADC_disableInt(obj->adcHandle,ADC_IntNumber_1);
  ADC_setIntMode(obj->adcHandle,ADC_IntNumber_1,ADC_IntMode_ClearFlag);
  ADC_setIntSrc(obj->adcHandle,ADC_IntNumber_1,ADC_IntSrc_EOC7);


  //configure the SOCs for boostxldrv8353
  // sample the first sample twice due to errata sprz342f
  // ISEN_A
  ADC_setSocChanNumber(obj->adcHandle,ADC_SocNumber_0,ADC_SocChanNumber_B3);
  ADC_setSocTrigSrc(obj->adcHandle,ADC_SocNumber_0,ADC_SocTrigSrc_EPWM1_ADCSOCA);
  ADC_setSocSampleDelay(obj->adcHandle,ADC_SocNumber_0,ADC_SocSampleDelay_9_cycles);

  // ISEN_A
  ADC_setSocChanNumber(obj->adcHandle,ADC_SocNumber_1,ADC_SocChanNumber_B3);
  ADC_setSocTrigSrc(obj->adcHandle,ADC_SocNumber_1,ADC_SocTrigSrc_EPWM1_ADCSOCA);
  ADC_setSocSampleDelay(obj->adcHandle,ADC_SocNumber_1,ADC_SocSampleDelay_9_cycles);

  // ISEN_B
  ADC_setSocChanNumber(obj->adcHandle,ADC_SocNumber_2,ADC_SocChanNumber_B1);
  ADC_setSocTrigSrc(obj->adcHandle,ADC_SocNumber_2,ADC_SocTrigSrc_EPWM1_ADCSOCA);
  ADC_setSocSampleDelay(obj->adcHandle,ADC_SocNumber_2,ADC_SocSampleDelay_9_cycles);

  // ISEN_C
  ADC_setSocChanNumber(obj->adcHandle,ADC_SocNumber_3,ADC_SocChanNumber_A0);
  ADC_setSocTrigSrc(obj->adcHandle,ADC_SocNumber_3,ADC_SocTrigSrc_EPWM1_ADCSOCA);
  ADC_setSocSampleDelay(obj->adcHandle,ADC_SocNumber_3,ADC_SocSampleDelay_9_cycles);

  // VSEN_A
  ADC_setSocChanNumber(obj->adcHandle,ADC_SocNumber_4,ADC_SocChanNumber_A7);
  ADC_setSocTrigSrc(obj->adcHandle,ADC_SocNumber_4,ADC_SocTrigSrc_EPWM1_ADCSOCA);
  ADC_setSocSampleDelay(obj->adcHandle,ADC_SocNumber_4,ADC_SocSampleDelay_9_cycles);

  // VSEN_B
  ADC_setSocChanNumber(obj->adcHandle,ADC_SocNumber_5,ADC_SocChanNumber_A3);
  ADC_setSocTrigSrc(obj->adcHandle,ADC_SocNumber_5,ADC_SocTrigSrc_EPWM1_ADCSOCA);
  ADC_setSocSampleDelay(obj->adcHandle,ADC_SocNumber_5,ADC_SocSampleDelay_9_cycles);

  // VSEN_C
  ADC_setSocChanNumber(obj->adcHandle,ADC_SocNumber_6,ADC_SocChanNumber_A1);
  ADC_setSocTrigSrc(obj->adcHandle,ADC_SocNumber_6,ADC_SocTrigSrc_EPWM1_ADCSOCA);
  ADC_setSocSampleDelay(obj->adcHandle,ADC_SocNumber_6,ADC_SocSampleDelay_9_cycles);

  // V_PVDD
  ADC_setSocChanNumber(obj->adcHandle,ADC_SocNumber_7,ADC_SocChanNumber_A6);
  ADC_setSocTrigSrc(obj->adcHandle,ADC_SocNumber_7,ADC_SocTrigSrc_EPWM1_ADCSOCA);
  ADC_setSocSampleDelay(obj->adcHandle,ADC_SocNumber_7,ADC_SocSampleDelay_16_cycles);

  // V_DeviceID
  // Potentiometer // Configure it so that ADCINT1 will trigger a potentiometer conversion
  ADC_setSocChanNumber(obj->adcHandle,ADC_SocNumber_8,ADC_SocChanNumber_B4);
  ADC_setupSocTrigSrc(obj->adcHandle, ADC_SocNumber_8, ADC_Int1TriggersSOC);
  ADC_setSocSampleDelay(obj->adcHandle,ADC_SocNumber_8,ADC_SocSampleDelay_9_cycles);

  return;
} // end of HAL_setupAdcs() function


void HAL_setupClks(HAL_Handle handle)
{
  HAL_Obj *obj = (HAL_Obj *)handle;


  // enable internal oscillator 1
  CLK_enableOsc1(obj->clkHandle);

  // set the oscillator source
  CLK_setOscSrc(obj->clkHandle,CLK_OscSrc_Internal);

  // disable the external clock in
  CLK_disableClkIn(obj->clkHandle);

  // disable the crystal oscillator
  CLK_disableCrystalOsc(obj->clkHandle);

  // disable oscillator 2
  CLK_disableOsc2(obj->clkHandle);

  // set the low speed clock prescaler
//  CLK_setLowSpdPreScaler(obj->clkHandle,CLK_LowSpdPreScaler_SysClkOut_by_4);
  CLK_setLowSpdPreScaler(obj->clkHandle,CLK_LowSpdPreScaler_SysClkOut_by_2);

  // set the clock out prescaler
  CLK_setClkOutPreScaler(obj->clkHandle,CLK_ClkOutPreScaler_SysClkOut_by_1);

  return;
} // end of HAL_setupClks() function


void HAL_setupFlash(HAL_Handle handle)
{
  HAL_Obj *obj = (HAL_Obj *)handle;


  FLASH_enablePipelineMode(obj->flashHandle);

  FLASH_setNumPagedReadWaitStates(obj->flashHandle,FLASH_NumPagedWaitStates_2);

  FLASH_setNumRandomReadWaitStates(obj->flashHandle,FLASH_NumRandomWaitStates_2);

  FLASH_setOtpWaitStates(obj->flashHandle,FLASH_NumOtpWaitStates_3);

  FLASH_setStandbyWaitCount(obj->flashHandle,FLASH_STANDBY_WAIT_COUNT_DEFAULT);

  FLASH_setActiveWaitCount(obj->flashHandle,FLASH_ACTIVE_WAIT_COUNT_DEFAULT);

  return;
} // HAL_setupFlash() function


void HAL_setupGate(HAL_Handle handle)
{
  HAL_Obj *obj = (HAL_Obj *)handle;
#ifdef DRV8353_SPI
  if(gDeviceVariant)
     DRV8353_setSpiHandle(obj->drv8353Handle,obj->spiAHandle);
#endif
  DRV8353_setGpioHandle(obj->drv8353Handle,obj->gpioHandle);
  DRV8353_setGpioNumber(obj->drv8353Handle,GPIO_Number_34);		// Enable Gate of DRV8353
} // HAL_setupGate() function


void HAL_setupGpios(HAL_Handle handle)
{
  HAL_Obj *obj = (HAL_Obj *)handle;

  // PWMA_H
  GPIO_setMode(obj->gpioHandle,GPIO_Number_0,GPIO_0_Mode_EPWM1A);

  // PWMA_L
  GPIO_setMode(obj->gpioHandle,GPIO_Number_1,GPIO_1_Mode_EPWM1B);

  // PWMB_H
  GPIO_setMode(obj->gpioHandle,GPIO_Number_2,GPIO_2_Mode_EPWM2A);

  // PWMB_L
  GPIO_setMode(obj->gpioHandle,GPIO_Number_3,GPIO_3_Mode_EPWM2B);
  
  // PWMC_H
  GPIO_setMode(obj->gpioHandle,GPIO_Number_4,GPIO_4_Mode_EPWM3A);

  // PWMC_L
  GPIO_setMode(obj->gpioHandle,GPIO_Number_5,GPIO_5_Mode_EPWM3B);

  // EN_GATE
  GPIO_setMode(obj->gpioHandle,GPIO_Number_6,GPIO_6_Mode_GeneralPurpose);
#ifdef DRV8353_SPI
  if(gDeviceVariant)
  {
	  // DRV8353 SCS/GAIN
	  GPIO_setMode(obj->gpioHandle,GPIO_Number_7,GPIO_7_Mode_GeneralPurpose);
	  GPIO_setHigh(obj->gpioHandle,GPIO_Number_7);
	  GPIO_setDirection(obj->gpioHandle,GPIO_Number_7,GPIO_Direction_Output);
  }
#endif
  // No Connection
  // To Read the Push Button SW3 to allow Motor to Run or Stop
  GPIO_setMode(obj->gpioHandle,GPIO_Number_12,GPIO_12_Mode_GeneralPurpose);
  GPIO_setDirection(obj->gpioHandle,GPIO_Number_12,GPIO_Direction_Input);

#ifdef DRV8353_SPI
  if(gDeviceVariant)
  {
	  // SPI_SDI if JP4 is soldered, No Connection if JP4 is not soldered
	  GPIO_setMode(obj->gpioHandle,GPIO_Number_16,GPIO_16_Mode_SPISIMOA);

	  // SPI_SDO if JP6 is soldered, No Connection if JP6 is not soldered
	  GPIO_setMode(obj->gpioHandle,GPIO_Number_17,GPIO_17_Mode_SPISOMIA);
	  GPIO_setPullUp(obj->gpioHandle, GPIO_Number_17, GPIO_PullUp_Disable);

	  // SPI_CLK
	  GPIO_setMode(obj->gpioHandle,GPIO_Number_18,GPIO_18_Mode_SPICLKA);

	  // SPI_SCS
	  GPIO_setMode(obj->gpioHandle,GPIO_Number_19,GPIO_19_Mode_GeneralPurpose);
  }
  else // Hardware Interface
#endif
  {
  // MODE
  GPIO_setMode(obj->gpioHandle,GPIO_Number_16,GPIO_16_Mode_GeneralPurpose);

  // LED
  GPIO_setMode(obj->gpioHandle,GPIO_Number_17,GPIO_17_Mode_GeneralPurpose);
 // GPIO_setPullUp(obj->gpioHandle, GPIO_Number_17, GPIO_PullUp_Disable);
  }

  // nFAULT
  GPIO_setMode(obj->gpioHandle,GPIO_Number_28,GPIO_28_Mode_GeneralPurpose);

  // No connection (TX)
  GPIO_setMode(obj->gpioHandle,GPIO_Number_29,GPIO_29_Mode_GeneralPurpose);

  // SPI_SDI if JP5 is soldered, No Connection if JP5 is not soldered
  GPIO_setMode(obj->gpioHandle,GPIO_Number_32,GPIO_32_Mode_GeneralPurpose);

  // SPI_SDO if JP7 is soldered, No Connection if JP7 is not soldered
  GPIO_setMode(obj->gpioHandle,GPIO_Number_33,GPIO_33_Mode_GeneralPurpose);

  // DRV8353 Enable Gate
  GPIO_setMode(obj->gpioHandle,GPIO_Number_34,GPIO_34_Mode_GeneralPurpose);
  GPIO_setLow(obj->gpioHandle,GPIO_Number_34);
  GPIO_setDirection(obj->gpioHandle,GPIO_Number_34,GPIO_Direction_Output);

  // JTAG
  GPIO_setMode(obj->gpioHandle,GPIO_Number_35,GPIO_35_Mode_JTAG_TDI);
  GPIO_setMode(obj->gpioHandle,GPIO_Number_36,GPIO_36_Mode_JTAG_TMS);
  GPIO_setMode(obj->gpioHandle,GPIO_Number_37,GPIO_37_Mode_JTAG_TDO);
  GPIO_setMode(obj->gpioHandle,GPIO_Number_38,GPIO_38_Mode_JTAG_TCK);

  return;
}  // end of HAL_setupGpios() function


void HAL_setupLaunchPadGpio0and1(HAL_Handle handle)
{
  HAL_Obj *obj = (HAL_Obj *)handle;

  // GPIO 0 (LED 2 on the LaunchPad)
  // Since the LaunchPad uses the same GPIO pins for LEDs as PWM pins,
  // the GPIO 0 and 1 are setup outside of the HAL file.
  GPIO_setMode(obj->gpioHandle,GPIO_Number_0,GPIO_0_Mode_GeneralPurpose);
  GPIO_setLow(obj->gpioHandle,GPIO_Number_0);
  GPIO_setDirection(obj->gpioHandle,GPIO_Number_0,GPIO_Direction_Output);

  // GPIO 1 (LED 4 on the LaunchPad)
  // Since the LaunchPad uses the same GPIO pins for LEDs as PWM pins,
  // the GPIO 0 and 1 are setup outside of the HAL file.  GPIO 1 will be
  // kept low so that there is no possibility of shoot-through conduction
  // with the high side switch that is controlled by GPIO0.
  GPIO_setMode(obj->gpioHandle,GPIO_Number_1,GPIO_1_Mode_GeneralPurpose);
  GPIO_setLow(obj->gpioHandle,GPIO_Number_1);
  GPIO_setDirection(obj->gpioHandle,GPIO_Number_1,GPIO_Direction_Output);

  return;
}  // end of HAL_setupGpios() function


void HAL_setupPie(HAL_Handle handle)
{
  HAL_Obj *obj = (HAL_Obj *)handle;


  PIE_disable(obj->pieHandle);

  PIE_disableAllInts(obj->pieHandle);

  PIE_clearAllInts(obj->pieHandle);

  PIE_clearAllFlags(obj->pieHandle);

  PIE_setDefaultIntVectorTable(obj->pieHandle);

  PIE_enable(obj->pieHandle);

  return;
} // end of HAL_setupPie() function


void HAL_setupPeripheralClks(HAL_Handle handle)
{
  HAL_Obj *obj = (HAL_Obj *)handle;


  CLK_enableAdcClock(obj->clkHandle);

  CLK_enableCompClock(obj->clkHandle,CLK_CompNumber_1);
  CLK_enableCompClock(obj->clkHandle,CLK_CompNumber_2);
  CLK_enableCompClock(obj->clkHandle,CLK_CompNumber_3);

  CLK_enableEcap1Clock(obj->clkHandle);

  CLK_enablePwmClock(obj->clkHandle,PWM_Number_1);
  CLK_enablePwmClock(obj->clkHandle,PWM_Number_2);
  CLK_enablePwmClock(obj->clkHandle,PWM_Number_3);
  CLK_enablePwmClock(obj->clkHandle,PWM_Number_4);

  CLK_disableHrPwmClock(obj->clkHandle);

  CLK_disableI2cClock(obj->clkHandle);

  CLK_enableSciaClock(obj->clkHandle);
#ifdef DRV8353_SPI
  if(gDeviceVariant)
	  CLK_enableSpiaClock(obj->clkHandle);
#endif
  CLK_enableTbClockSync(obj->clkHandle);

  return;
} // end of HAL_setupPeripheralClks() function


void HAL_setupPll(HAL_Handle handle,const PLL_ClkFreq_e clkFreq)
{
  HAL_Obj *obj = (HAL_Obj *)handle;


  // make sure PLL is not running in limp mode
  if(PLL_getClkStatus(obj->pllHandle) != PLL_ClkStatus_Normal)
    {
      // reset the clock detect
      PLL_resetClkDetect(obj->pllHandle);

      // ???????
      asm("        ESTOP0");
    }


  // Divide Select must be ClkIn/4 before the clock rate can be changed
  if(PLL_getDivideSelect(obj->pllHandle) != PLL_DivideSelect_ClkIn_by_4)
    {
      PLL_setDivideSelect(obj->pllHandle,PLL_DivideSelect_ClkIn_by_4);
    }


  if(PLL_getClkFreq(obj->pllHandle) != clkFreq)
    {
      // disable the clock detect
      PLL_disableClkDetect(obj->pllHandle);

      // set the clock rate
      PLL_setClkFreq(obj->pllHandle,clkFreq);
    }


  // wait until locked
  while(PLL_getLockStatus(obj->pllHandle) != PLL_LockStatus_Done) {}


  // enable the clock detect
  PLL_enableClkDetect(obj->pllHandle);


  // set divide select to ClkIn/2 to get desired clock rate
  // NOTE: clock must be locked before setting this register
  PLL_setDivideSelect(obj->pllHandle,PLL_DivideSelect_ClkIn_by_2);

  return;
} // end of HAL_setupPll() function


void HAL_setupPwms(HAL_Handle handle,
                   const float_t systemFreq_MHz,
                   const float_t pwmPeriod_usec,
                   const uint_least16_t numPwmTicksPerIsrTick)
{
  HAL_Obj   *obj = (HAL_Obj *)handle;
  uint16_t   halfPeriod_cycles = (uint16_t)(systemFreq_MHz*pwmPeriod_usec) >> 1;
  uint_least8_t    cnt;


  // turns off the outputs of the EPWM peripherals which will put the power switches
  // into a high impedance state.
  PWM_setOneShotTrip(obj->pwmHandle[PWM_Number_1]);
  PWM_setOneShotTrip(obj->pwmHandle[PWM_Number_2]);
  PWM_setOneShotTrip(obj->pwmHandle[PWM_Number_3]);
  // first step to synchronize the pwms
  CLK_disableTbClockSync(obj->clkHandle);

  for(cnt=0;cnt<3;cnt++)
    {
      // setup the Time-Base Control Register (TBCTL)
      PWM_setCounterMode(obj->pwmHandle[cnt],PWM_CounterMode_UpDown);
      PWM_disableCounterLoad(obj->pwmHandle[cnt]);
      PWM_setPeriodLoad(obj->pwmHandle[cnt],PWM_PeriodLoad_Immediate);
      PWM_setSyncMode(obj->pwmHandle[cnt],PWM_SyncMode_EPWMxSYNC);
      PWM_setHighSpeedClkDiv(obj->pwmHandle[cnt],PWM_HspClkDiv_by_1);
      PWM_setClkDiv(obj->pwmHandle[cnt],PWM_ClkDiv_by_1);
      PWM_setPhaseDir(obj->pwmHandle[cnt],PWM_PhaseDir_CountUp);
      PWM_setRunMode(obj->pwmHandle[cnt],PWM_RunMode_FreeRun);

      // setup the Timer-Based Phase Register (TBPHS)
      PWM_setPhase(obj->pwmHandle[cnt],0);

      // setup the Time-Base Counter Register (TBCTR)
      PWM_setCount(obj->pwmHandle[cnt],0);

      // setup the Time-Base Period Register (TBPRD)
      // set to zero initially
      PWM_setPeriod(obj->pwmHandle[cnt],0);

      // setup the Counter-Compare Control Register (CMPCTL)
      PWM_setLoadMode_CmpA(obj->pwmHandle[cnt],PWM_LoadMode_Zero);
      PWM_setLoadMode_CmpB(obj->pwmHandle[cnt],PWM_LoadMode_Zero);
      PWM_setShadowMode_CmpA(obj->pwmHandle[cnt],PWM_ShadowMode_Shadow);
      PWM_setShadowMode_CmpB(obj->pwmHandle[cnt],PWM_ShadowMode_Immediate);

      // setup the Action-Qualifier Output A Register (AQCTLA) 
      PWM_setActionQual_CntUp_CmpA_PwmA(obj->pwmHandle[cnt],PWM_ActionQual_Set);
      PWM_setActionQual_CntDown_CmpA_PwmA(obj->pwmHandle[cnt],PWM_ActionQual_Clear);

      // setup the Dead-Band Generator Control Register (DBCTL)
      PWM_setDeadBandOutputMode(obj->pwmHandle[cnt],PWM_DeadBandOutputMode_EPWMxA_Rising_EPWMxB_Falling);
      PWM_setDeadBandPolarity(obj->pwmHandle[cnt],PWM_DeadBandPolarity_EPWMxB_Inverted);

      // setup the Dead-Band Rising Edge Delay Register (DBRED)
      PWM_setDeadBandRisingEdgeDelay(obj->pwmHandle[cnt],HAL_PWM_DBRED_CNT);

      // setup the Dead-Band Falling Edge Delay Register (DBFED)
      PWM_setDeadBandFallingEdgeDelay(obj->pwmHandle[cnt],HAL_PWM_DBFED_CNT);
      // setup the PWM-Chopper Control Register (PCCTL)
      PWM_disableChopping(obj->pwmHandle[cnt]);

      // setup the Trip Zone Select Register (TZSEL)
      PWM_disableTripZones(obj->pwmHandle[cnt]);
    }


  // setup the Event Trigger Selection Register (ETSEL)
  PWM_disableInt(obj->pwmHandle[PWM_Number_1]);
  PWM_setSocAPulseSrc(obj->pwmHandle[PWM_Number_1],PWM_SocPulseSrc_CounterEqualZero);
  PWM_enableSocAPulse(obj->pwmHandle[PWM_Number_1]);
  

  // setup the Event Trigger Prescale Register (ETPS)
  if(numPwmTicksPerIsrTick == 3)
    {
      PWM_setIntPeriod(obj->pwmHandle[PWM_Number_1],PWM_IntPeriod_ThirdEvent);
      PWM_setSocAPeriod(obj->pwmHandle[PWM_Number_1],PWM_SocPeriod_ThirdEvent);
    }
  else if(numPwmTicksPerIsrTick == 2)
    {
      PWM_setIntPeriod(obj->pwmHandle[PWM_Number_1],PWM_IntPeriod_SecondEvent);
      PWM_setSocAPeriod(obj->pwmHandle[PWM_Number_1],PWM_SocPeriod_SecondEvent);
    }
  else
    {
      PWM_setIntPeriod(obj->pwmHandle[PWM_Number_1],PWM_IntPeriod_FirstEvent);
      PWM_setSocAPeriod(obj->pwmHandle[PWM_Number_1],PWM_SocPeriod_FirstEvent);
    }


  // setup the Event Trigger Clear Register (ETCLR)
  PWM_clearIntFlag(obj->pwmHandle[PWM_Number_1]);
  PWM_clearSocAFlag(obj->pwmHandle[PWM_Number_1]);


  // since the PWM is configured as an up/down counter, the period register is set to one-half 
  // of the desired PWM period
  PWM_setPeriod(obj->pwmHandle[PWM_Number_1],halfPeriod_cycles);
  PWM_setPeriod(obj->pwmHandle[PWM_Number_2],halfPeriod_cycles);
  PWM_setPeriod(obj->pwmHandle[PWM_Number_3],halfPeriod_cycles);

  // last step to synchronize the pwms
  CLK_enableTbClockSync(obj->clkHandle);

  return;
}  // end of HAL_setupPwms() function

#ifdef DRV8353_SPI
void HAL_setupSpiA(HAL_Handle handle)
{
  HAL_Obj   *obj = (HAL_Obj *)handle;

  SPI_reset(obj->spiAHandle);
  SPI_setMode(obj->spiAHandle,SPI_Mode_Master);
  SPI_setClkPolarity(obj->spiAHandle,SPI_ClkPolarity_OutputRisingEdge_InputFallingEdge);
  SPI_enableTx(obj->spiAHandle);
  SPI_enableTxFifoEnh(obj->spiAHandle);
  SPI_enableTxFifo(obj->spiAHandle);
  SPI_setTxDelay(obj->spiAHandle,0x0010);
  SPI_setBaudRate(obj->spiAHandle,(SPI_BaudRate_e)(0x0010));
  SPI_setCharLength(obj->spiAHandle,SPI_CharLength_16_Bits);
  SPI_setSuspend(obj->spiAHandle,SPI_TxSuspend_free);
  SPI_enable(obj->spiAHandle);

  return;
}  // end of HAL_setupSpiA() function
#endif

void HAL_setupTimers(HAL_Handle handle,const float_t systemFreq_MHz)
{
  HAL_Obj  *obj = (HAL_Obj *)handle;
  uint32_t  timerPeriod_0p5ms = (uint32_t)(systemFreq_MHz * (float_t)500.0) - 1;
  uint32_t  timerPeriod_10ms = (uint32_t)(systemFreq_MHz * (float_t)10000.0) - 1;

  // use timer 0 for frequency diagnostics
  TIMER_setDecimationFactor(obj->timerHandle[0],0);
  TIMER_setEmulationMode(obj->timerHandle[0],TIMER_EmulationMode_RunFree);
  TIMER_setPeriod(obj->timerHandle[0],timerPeriod_0p5ms);
  TIMER_setPreScaler(obj->timerHandle[0],0);

  // use timer 1 for CPU usage diagnostics
  TIMER_setDecimationFactor(obj->timerHandle[1],0);
  TIMER_setEmulationMode(obj->timerHandle[1],TIMER_EmulationMode_RunFree);
  TIMER_setPeriod(obj->timerHandle[1],timerPeriod_10ms);
  TIMER_setPreScaler(obj->timerHandle[1],0);

  // use timer 2 for CPU time diagnostics
  TIMER_setDecimationFactor(obj->timerHandle[2],0);
  TIMER_setEmulationMode(obj->timerHandle[2],TIMER_EmulationMode_RunFree);
  TIMER_setPeriod(obj->timerHandle[2],0xFFFFFFFF);
  TIMER_setPreScaler(obj->timerHandle[2],0);

  return;
}  // end of HAL_setupTimers() function

#ifdef DRV8353_SPI
void HAL_writeDrvData(HAL_Handle handle, DRV_SPI_8353_Vars_t *Spi_8353_Vars)
{
  HAL_Obj  *obj = (HAL_Obj *)handle;

  DRV8353_writeData(obj->drv8353Handle,Spi_8353_Vars);
  
  return;
}  // end of HAL_writeDrvData() function


void HAL_readDrvData(HAL_Handle handle, DRV_SPI_8353_Vars_t *Spi_8353_Vars)
{
  HAL_Obj  *obj = (HAL_Obj *)handle;

  DRV8353_readData(obj->drv8353Handle,Spi_8353_Vars);
  
  return;
}  // end of HAL_readDrvData() function


void HAL_setupDrvSpi(HAL_Handle handle, DRV_SPI_8353_Vars_t *Spi_8353_Vars)
{
  HAL_Obj  *obj = (HAL_Obj *)handle;

  DRV8353_setupSpi(obj->drv8353Handle,Spi_8353_Vars);

  return;
}  // end of HAL_setupDrvSpi() function
#endif
void HAL_setDacParameters(HAL_Handle handle, HAL_DacData_t *pDacData)
{
	HAL_Obj *obj = (HAL_Obj *)handle;

	pDacData->PeriodMax = PWMDAC_getPeriod(obj->pwmDacHandle[PWMDAC_Number_1]);

	pDacData->offset[0] = _IQ(0.5);
	pDacData->offset[1] = _IQ(0.5);
	pDacData->offset[2] = _IQ(0.0);
	pDacData->offset[3] = _IQ(0.0);

	pDacData->gain[0] = _IQ(1.0);
	pDacData->gain[1] = _IQ(1.0);
	pDacData->gain[2] = _IQ(1.0);
	pDacData->gain[3] = _IQ(1.0);

	return;
}	//end of HAL_setDacParameters() function

// end of file

/* --COPYRIGHT--,BSD
 * Copyright (c) 2015, Texas Instruments Incorporated
 * All rights reserved.
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions
 * are met:
 *
 * *  Redistributions of source code must retain the above copyright
 *    notice, this list of conditions and the following disclaimer.
 *
 * *  Redistributions in binary form must reproduce the above copyright
 *    notice, this list of conditions and the following disclaimer in the
 *    documentation and/or other materials provided with the distribution.
 *
 * *  Neither the name of Texas Instruments Incorporated nor the names of
 *    its contributors may be used to endorse or promote products derived
 *    from this software without specific prior written permission.
 *
 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
 * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
 * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
 * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
 * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
 * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
 * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS;
 * OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
 * WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR
 * OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
 * EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
 * --/COPYRIGHT--*/
//! \file  sw/modules/hal/boards/boostxldrv8353/f28x/f2802xF/src/hal.c
//! \brief Contains the various functions related to the HAL object (everything outside the CTRL system) 
//!
//! (C) Copyright 2015, Texas Instruments, Inc.


// **************************************************************************
// the includes

// drivers

// modules

// platforms
#include "hal.h"
#include "user.h"
#include "hal_obj.h"

#ifdef FLASH
#pragma CODE_SECTION(HAL_setupFlash,"ramfuncs");
#endif

// **************************************************************************
// the defines

#define US_TO_CNT(A) ((((long double) A * (long double)USER_SYSTEM_FREQ_MHz) - 9.0L) / 5.0L)

// **************************************************************************
// the globals

#ifdef F2802xF
#pragma DATA_SECTION(hal,"rom_accessed_data");
#endif

HAL_Obj hal;


// **************************************************************************
// the functions

void HAL_cal(HAL_Handle handle)
{
  HAL_Obj *obj = (HAL_Obj *)handle;


  // enable the ADC clock
  CLK_enableAdcClock(obj->clkHandle);


  // Run the Device_cal() function
  // This function copies the ADC and oscillator calibration values from TI reserved
  // OTP into the appropriate trim registers
  // This boot ROM automatically calls this function to calibrate the interal 
  // oscillators and ADC with device specific calibration data.
  // If the boot ROM is bypassed by Code Composer Studio during the development process,
  // then the calibration must be initialized by the application
  ENABLE_PROTECTED_REGISTER_WRITE_MODE;
  (*Device_cal)();
  DISABLE_PROTECTED_REGISTER_WRITE_MODE;

  // run offsets calibration in user's memory
  HAL_AdcOffsetSelfCal(handle);

  // run oscillator compensation
  HAL_OscTempComp(handle);

  // disable the ADC clock
  CLK_disableAdcClock(obj->clkHandle);

  return;
} // end of HAL_cal() function


void HAL_OscTempComp(HAL_Handle handle)
{
  HAL_Obj *obj = (HAL_Obj *)handle;
  uint16_t Temperature;

  // disable the ADCs
  ADC_disable(obj->adcHandle);

  // power up the bandgap circuit
  ADC_enableBandGap(obj->adcHandle);

  // set the ADC voltage reference source to internal
  ADC_setVoltRefSrc(obj->adcHandle,ADC_VoltageRefSrc_Int);

  // enable the ADC reference buffers
  ADC_enableRefBuffers(obj->adcHandle);

  // Set main clock scaling factor (max45MHz clock for the ADC module)
  ADC_setDivideSelect(obj->adcHandle,ADC_DivideSelect_ClkIn_by_2);

  // power up the ADCs
  ADC_powerUp(obj->adcHandle);

  // enable the ADCs
  ADC_enable(obj->adcHandle);

  // enable non-overlap mode
  ADC_enableNoOverlapMode(obj->adcHandle);

  // connect channel A5 internally to the temperature sensor
  ADC_setTempSensorSrc(obj->adcHandle, ADC_TempSensorSrc_Int);

  // set SOC0 channel select to ADCINA5
  ADC_setSocChanNumber(obj->adcHandle, ADC_SocNumber_0, ADC_SocChanNumber_A5);

  // set SOC0 acquisition period to 26 ADCCLK
  ADC_setSocSampleDelay(obj->adcHandle, ADC_SocNumber_0, ADC_SocSampleDelay_64_cycles);

  // connect ADCINT1 to EOC0
  ADC_setIntSrc(obj->adcHandle, ADC_IntNumber_1, ADC_IntSrc_EOC0);

  // clear ADCINT1 flag
  ADC_clearIntFlag(obj->adcHandle, ADC_IntNumber_1);

  // enable ADCINT1
  ADC_enableInt(obj->adcHandle, ADC_IntNumber_1);

  // force start of conversion on SOC0
  ADC_setSocFrc(obj->adcHandle, ADC_SocFrc_0);

  // wait for end of conversion
  while (ADC_getIntFlag(obj->adcHandle, ADC_IntNumber_1) == 0){}

  // clear ADCINT1 flag
  ADC_clearIntFlag(obj->adcHandle, ADC_IntNumber_1);

  Temperature = ADC_readResult(obj->adcHandle, ADC_ResultNumber_0);

  HAL_osc1Comp(handle, Temperature);

  HAL_osc2Comp(handle, Temperature);

  return;
} // end of HAL_OscTempComp() function


void HAL_osc1Comp(HAL_Handle handle, const int16_t sensorSample)
{
	int16_t compOscFineTrim;
	HAL_Obj *obj = (HAL_Obj *)handle;

	ENABLE_PROTECTED_REGISTER_WRITE_MODE;

    compOscFineTrim = ((sensorSample - getRefTempOffset())*(int32_t)getOsc1FineTrimSlope()
                      + OSC_POSTRIM_OFF + FP_ROUND )/FP_SCALE + getOsc1FineTrimOffset() - OSC_POSTRIM;

    if(compOscFineTrim > 31)
      {
        compOscFineTrim = 31;
      }
	else if(compOscFineTrim < -31)
      {
        compOscFineTrim = -31;
      }

    OSC_setTrim(obj->oscHandle, OSC_Number_1, HAL_getOscTrimValue(getOsc1CoarseTrim(), compOscFineTrim));

    DISABLE_PROTECTED_REGISTER_WRITE_MODE;

    return;
} // end of HAL_osc1Comp() function


void HAL_osc2Comp(HAL_Handle handle, const int16_t sensorSample)
{
	int16_t compOscFineTrim;
	HAL_Obj *obj = (HAL_Obj *)handle;

	ENABLE_PROTECTED_REGISTER_WRITE_MODE;

    compOscFineTrim = ((sensorSample - getRefTempOffset())*(int32_t)getOsc2FineTrimSlope()
                      + OSC_POSTRIM_OFF + FP_ROUND )/FP_SCALE + getOsc2FineTrimOffset() - OSC_POSTRIM;

    if(compOscFineTrim > 31)
      {
        compOscFineTrim = 31;
      }
	else if(compOscFineTrim < -31)
      {
        compOscFineTrim = -31;
      }

    OSC_setTrim(obj->oscHandle, OSC_Number_2, HAL_getOscTrimValue(getOsc2CoarseTrim(), compOscFineTrim));

    DISABLE_PROTECTED_REGISTER_WRITE_MODE;

    return;
} // end of HAL_osc2Comp() function


uint16_t HAL_getOscTrimValue(int16_t coarse, int16_t fine)
{
  uint16_t regValue = 0;

  if(fine < 0)
    {
      regValue = ((-fine) | 0x20) << 9;
    }
  else
    {
      regValue = fine << 9;
    }

  if(coarse < 0)
    {
      regValue |= ((-coarse) | 0x80);
    }
  else
    {
      regValue |= coarse;
    }

  return regValue;
} // end of HAL_getOscTrimValue() function


void HAL_AdcOffsetSelfCal(HAL_Handle handle)
{
  HAL_Obj *obj = (HAL_Obj *)handle;
  uint16_t AdcConvMean;

  // disable the ADCs
  ADC_disable(obj->adcHandle);

  // power up the bandgap circuit
  ADC_enableBandGap(obj->adcHandle);

  // set the ADC voltage reference source to internal
  ADC_setVoltRefSrc(obj->adcHandle,ADC_VoltageRefSrc_Int);

  // enable the ADC reference buffers
  ADC_enableRefBuffers(obj->adcHandle);

  // power up the ADCs
  ADC_powerUp(obj->adcHandle);

  // enable the ADCs
  ADC_enable(obj->adcHandle);

  //Select VREFLO internal connection on B5
  ADC_enableVoltRefLoConv(obj->adcHandle);

  //Select channel B5 for all SOC
  HAL_AdcCalChanSelect(handle, ADC_SocChanNumber_B5);

  //Apply artificial offset (+80) to account for a negative offset that may reside in the ADC core
  ADC_setOffTrim(obj->adcHandle, 80);

  //Capture ADC conversion on VREFLO
  AdcConvMean = HAL_AdcCalConversion(handle);

  //Set offtrim register with new value (i.e remove artical offset (+80) and create a two's compliment of the offset error)
  ADC_setOffTrim(obj->adcHandle, 80 - AdcConvMean);

  //Select external ADCIN5 input pin on B5
  ADC_disableVoltRefLoConv(obj->adcHandle);

  return;
} // end of HAL_AdcOffsetSelfCal() function


void HAL_AdcCalChanSelect(HAL_Handle handle, const ADC_SocChanNumber_e chanNumber)
{
  HAL_Obj *obj = (HAL_Obj *)handle;

  ADC_setSocChanNumber(obj->adcHandle,ADC_SocNumber_0,chanNumber);
  ADC_setSocChanNumber(obj->adcHandle,ADC_SocNumber_1,chanNumber);
  ADC_setSocChanNumber(obj->adcHandle,ADC_SocNumber_2,chanNumber);
  ADC_setSocChanNumber(obj->adcHandle,ADC_SocNumber_3,chanNumber);
  ADC_setSocChanNumber(obj->adcHandle,ADC_SocNumber_4,chanNumber);
  ADC_setSocChanNumber(obj->adcHandle,ADC_SocNumber_5,chanNumber);
  ADC_setSocChanNumber(obj->adcHandle,ADC_SocNumber_6,chanNumber);
  ADC_setSocChanNumber(obj->adcHandle,ADC_SocNumber_7,chanNumber);
  ADC_setSocChanNumber(obj->adcHandle,ADC_SocNumber_8,chanNumber);
  ADC_setSocChanNumber(obj->adcHandle,ADC_SocNumber_9,chanNumber);
  ADC_setSocChanNumber(obj->adcHandle,ADC_SocNumber_10,chanNumber);
  ADC_setSocChanNumber(obj->adcHandle,ADC_SocNumber_11,chanNumber);
  ADC_setSocChanNumber(obj->adcHandle,ADC_SocNumber_12,chanNumber);
  ADC_setSocChanNumber(obj->adcHandle,ADC_SocNumber_13,chanNumber);
  ADC_setSocChanNumber(obj->adcHandle,ADC_SocNumber_14,chanNumber);
  ADC_setSocChanNumber(obj->adcHandle,ADC_SocNumber_15,chanNumber);

  return;
} // end of HAL_AdcCalChanSelect() function


uint16_t HAL_AdcCalConversion(HAL_Handle handle)
{
  HAL_Obj *obj = (HAL_Obj *)handle;
  uint16_t index, SampleSize, Mean;
  uint32_t Sum;
  ADC_SocSampleDelay_e ACQPS_Value;

  index       = 0;     //initialize index to 0
  SampleSize  = 256;   //set sample size to 256 (**NOTE: Sample size must be multiples of 2^x where is an integer >= 4)
  Sum         = 0;     //set sum to 0
  Mean        = 999;   //initialize mean to known value

  //Set the ADC sample window to the desired value (Sample window = ACQPS + 1)
  ACQPS_Value = ADC_SocSampleDelay_7_cycles;

  ADC_setSocSampleDelay(obj->adcHandle,ADC_SocNumber_0,ACQPS_Value);
  ADC_setSocSampleDelay(obj->adcHandle,ADC_SocNumber_1,ACQPS_Value);
  ADC_setSocSampleDelay(obj->adcHandle,ADC_SocNumber_2,ACQPS_Value);
  ADC_setSocSampleDelay(obj->adcHandle,ADC_SocNumber_3,ACQPS_Value);
  ADC_setSocSampleDelay(obj->adcHandle,ADC_SocNumber_4,ACQPS_Value);
  ADC_setSocSampleDelay(obj->adcHandle,ADC_SocNumber_5,ACQPS_Value);
  ADC_setSocSampleDelay(obj->adcHandle,ADC_SocNumber_6,ACQPS_Value);
  ADC_setSocSampleDelay(obj->adcHandle,ADC_SocNumber_7,ACQPS_Value);
  ADC_setSocSampleDelay(obj->adcHandle,ADC_SocNumber_8,ACQPS_Value);
  ADC_setSocSampleDelay(obj->adcHandle,ADC_SocNumber_9,ACQPS_Value);
  ADC_setSocSampleDelay(obj->adcHandle,ADC_SocNumber_10,ACQPS_Value);
  ADC_setSocSampleDelay(obj->adcHandle,ADC_SocNumber_11,ACQPS_Value);
  ADC_setSocSampleDelay(obj->adcHandle,ADC_SocNumber_12,ACQPS_Value);
  ADC_setSocSampleDelay(obj->adcHandle,ADC_SocNumber_13,ACQPS_Value);
  ADC_setSocSampleDelay(obj->adcHandle,ADC_SocNumber_14,ACQPS_Value);
  ADC_setSocSampleDelay(obj->adcHandle,ADC_SocNumber_15,ACQPS_Value);

  // Enabled ADCINT1 and ADCINT2
  ADC_enableInt(obj->adcHandle, ADC_IntNumber_1);
  ADC_enableInt(obj->adcHandle, ADC_IntNumber_2);

  // Disable continuous sampling for ADCINT1 and ADCINT2
  ADC_setIntMode(obj->adcHandle, ADC_IntNumber_1, ADC_IntMode_EOC);
  ADC_setIntMode(obj->adcHandle, ADC_IntNumber_2, ADC_IntMode_EOC);

  //ADCINTs trigger at end of conversion
  ADC_setIntPulseGenMode(obj->adcHandle, ADC_IntPulseGenMode_Prior);

  // Setup ADCINT1 and ADCINT2 trigger source
  ADC_setIntSrc(obj->adcHandle, ADC_IntNumber_1, ADC_IntSrc_EOC6);
  ADC_setIntSrc(obj->adcHandle, ADC_IntNumber_2, ADC_IntSrc_EOC14);

  // Setup each SOC's ADCINT trigger source
  ADC_setupSocTrigSrc(obj->adcHandle, ADC_SocNumber_0, ADC_Int2TriggersSOC);
  ADC_setupSocTrigSrc(obj->adcHandle, ADC_SocNumber_1, ADC_Int2TriggersSOC);
  ADC_setupSocTrigSrc(obj->adcHandle, ADC_SocNumber_2, ADC_Int2TriggersSOC);
  ADC_setupSocTrigSrc(obj->adcHandle, ADC_SocNumber_3, ADC_Int2TriggersSOC);
  ADC_setupSocTrigSrc(obj->adcHandle, ADC_SocNumber_4, ADC_Int2TriggersSOC);
  ADC_setupSocTrigSrc(obj->adcHandle, ADC_SocNumber_5, ADC_Int2TriggersSOC);
  ADC_setupSocTrigSrc(obj->adcHandle, ADC_SocNumber_6, ADC_Int2TriggersSOC);
  ADC_setupSocTrigSrc(obj->adcHandle, ADC_SocNumber_7, ADC_Int2TriggersSOC);
  ADC_setupSocTrigSrc(obj->adcHandle, ADC_SocNumber_8, ADC_Int1TriggersSOC);
  ADC_setupSocTrigSrc(obj->adcHandle, ADC_SocNumber_9, ADC_Int1TriggersSOC);
  ADC_setupSocTrigSrc(obj->adcHandle, ADC_SocNumber_10, ADC_Int1TriggersSOC);
  ADC_setupSocTrigSrc(obj->adcHandle, ADC_SocNumber_11, ADC_Int1TriggersSOC);
  ADC_setupSocTrigSrc(obj->adcHandle, ADC_SocNumber_12, ADC_Int1TriggersSOC);
  ADC_setupSocTrigSrc(obj->adcHandle, ADC_SocNumber_13, ADC_Int1TriggersSOC);
  ADC_setupSocTrigSrc(obj->adcHandle, ADC_SocNumber_14, ADC_Int1TriggersSOC);
  ADC_setupSocTrigSrc(obj->adcHandle, ADC_SocNumber_15, ADC_Int1TriggersSOC);

  // Delay before converting ADC channels
  usDelay(US_TO_CNT(ADC_DELAY_usec));

  ADC_setSocFrcWord(obj->adcHandle, 0x00FF);

  while( index < SampleSize )
    {
      //Wait for ADCINT1 to trigger, then add ADCRESULT0-7 registers to sum
      while (ADC_getIntFlag(obj->adcHandle, ADC_IntNumber_1) == 0){}

      //Must clear ADCINT1 flag since INT1CONT = 0
      ADC_clearIntFlag(obj->adcHandle, ADC_IntNumber_1);

      Sum += ADC_readResult(obj->adcHandle, ADC_ResultNumber_0);
      Sum += ADC_readResult(obj->adcHandle, ADC_ResultNumber_1);
      Sum += ADC_readResult(obj->adcHandle, ADC_ResultNumber_2);
      Sum += ADC_readResult(obj->adcHandle, ADC_ResultNumber_3);
      Sum += ADC_readResult(obj->adcHandle, ADC_ResultNumber_4);
      Sum += ADC_readResult(obj->adcHandle, ADC_ResultNumber_5);
      Sum += ADC_readResult(obj->adcHandle, ADC_ResultNumber_6);
      Sum += ADC_readResult(obj->adcHandle, ADC_ResultNumber_7);

      //Wait for ADCINT2 to trigger, then add ADCRESULT8-15 registers to sum
      while (ADC_getIntFlag(obj->adcHandle, ADC_IntNumber_2) == 0){}

      //Must clear ADCINT2 flag since INT2CONT = 0
      ADC_clearIntFlag(obj->adcHandle, ADC_IntNumber_2);

      Sum += ADC_readResult(obj->adcHandle, ADC_ResultNumber_8);
      Sum += ADC_readResult(obj->adcHandle, ADC_ResultNumber_9);
      Sum += ADC_readResult(obj->adcHandle, ADC_ResultNumber_10);
      Sum += ADC_readResult(obj->adcHandle, ADC_ResultNumber_11);
      Sum += ADC_readResult(obj->adcHandle, ADC_ResultNumber_12);
      Sum += ADC_readResult(obj->adcHandle, ADC_ResultNumber_13);
      Sum += ADC_readResult(obj->adcHandle, ADC_ResultNumber_14);
      Sum += ADC_readResult(obj->adcHandle, ADC_ResultNumber_15);

      index+=16;

  } // end data collection

  //Disable ADCINT1 and ADCINT2 to STOP the ping-pong sampling
  ADC_disableInt(obj->adcHandle, ADC_IntNumber_1);
  ADC_disableInt(obj->adcHandle, ADC_IntNumber_2);

  //Calculate average ADC sample value
  Mean = Sum / SampleSize;

  // Clear start of conversion trigger
  ADC_setupSocTrigSrc(obj->adcHandle, ADC_SocNumber_0, ADC_NoIntTriggersSOC);
  ADC_setupSocTrigSrc(obj->adcHandle, ADC_SocNumber_1, ADC_NoIntTriggersSOC);
  ADC_setupSocTrigSrc(obj->adcHandle, ADC_SocNumber_2, ADC_NoIntTriggersSOC);
  ADC_setupSocTrigSrc(obj->adcHandle, ADC_SocNumber_3, ADC_NoIntTriggersSOC);
  ADC_setupSocTrigSrc(obj->adcHandle, ADC_SocNumber_4, ADC_NoIntTriggersSOC);
  ADC_setupSocTrigSrc(obj->adcHandle, ADC_SocNumber_5, ADC_NoIntTriggersSOC);
  ADC_setupSocTrigSrc(obj->adcHandle, ADC_SocNumber_6, ADC_NoIntTriggersSOC);
  ADC_setupSocTrigSrc(obj->adcHandle, ADC_SocNumber_7, ADC_NoIntTriggersSOC);
  ADC_setupSocTrigSrc(obj->adcHandle, ADC_SocNumber_8, ADC_NoIntTriggersSOC);
  ADC_setupSocTrigSrc(obj->adcHandle, ADC_SocNumber_9, ADC_NoIntTriggersSOC);
  ADC_setupSocTrigSrc(obj->adcHandle, ADC_SocNumber_10, ADC_NoIntTriggersSOC);
  ADC_setupSocTrigSrc(obj->adcHandle, ADC_SocNumber_11, ADC_NoIntTriggersSOC);
  ADC_setupSocTrigSrc(obj->adcHandle, ADC_SocNumber_12, ADC_NoIntTriggersSOC);
  ADC_setupSocTrigSrc(obj->adcHandle, ADC_SocNumber_13, ADC_NoIntTriggersSOC);
  ADC_setupSocTrigSrc(obj->adcHandle, ADC_SocNumber_14, ADC_NoIntTriggersSOC);
  ADC_setupSocTrigSrc(obj->adcHandle, ADC_SocNumber_15, ADC_NoIntTriggersSOC);

  //return the average
  return(Mean);
} // end of HAL_AdcCalConversion() function


void HAL_disableWdog(HAL_Handle halHandle)
{
  HAL_Obj *hal = (HAL_Obj *)halHandle;


  WDOG_disable(hal->wdogHandle);


  return;
} // end of HAL_disableWdog() function


void HAL_disableGlobalInts(HAL_Handle handle)
{
  HAL_Obj *obj = (HAL_Obj *)handle;


  CPU_disableGlobalInts(obj->cpuHandle);

  return;
} // end of HAL_disableGlobalInts() function


void HAL_enableAdcInts(HAL_Handle handle)
{
  HAL_Obj *obj = (HAL_Obj *)handle;


  // enable the PIE interrupts associated with the ADC interrupts
  PIE_enableAdcInt(obj->pieHandle,ADC_IntNumber_1);


  // enable the ADC interrupts
  ADC_enableInt(obj->adcHandle,ADC_IntNumber_1);


  // enable the cpu interrupt for ADC interrupts
  CPU_enableInt(obj->cpuHandle,CPU_IntNumber_10);

  return;
} // end of HAL_enableAdcInts() function


void HAL_enableDebugInt(HAL_Handle handle)
{
  HAL_Obj *obj = (HAL_Obj *)handle;


  CPU_enableDebugInt(obj->cpuHandle);

  return;
} // end of HAL_enableDebugInt() function


void HAL_enableDrv(HAL_Handle handle)
{
  HAL_Obj *obj = (HAL_Obj *)handle;

  DRV8353_enable(obj->drv8353Handle);

  return;
}  // end of HAL_enableDrv() function


void HAL_enableGlobalInts(HAL_Handle handle)
{
  HAL_Obj *obj = (HAL_Obj *)handle;


  CPU_enableGlobalInts(obj->cpuHandle);

  return;
} // end of HAL_enableGlobalInts() function


void HAL_enablePwmInt(HAL_Handle handle)
{
  HAL_Obj *obj = (HAL_Obj *)handle;


  PIE_enablePwmInt(obj->pieHandle,PWM_Number_1);


  // enable the interrupt
  PWM_enableInt(obj->pwmHandle[PWM_Number_1]);


  // enable the cpu interrupt for EPWM1_INT
  CPU_enableInt(obj->cpuHandle,CPU_IntNumber_3);

  return;
} // end of HAL_enablePwmInt() function


void HAL_setupFaults(HAL_Handle handle)
{
  HAL_Obj *obj = (HAL_Obj *)handle;
  uint_least8_t cnt;

  // Configure Trip Mechanism for the Motor control software
  // -Cycle by cycle trip on CPU halt
  // -One shot fault trip zone
  // These trips need to be repeated for EPWM1 ,2 & 3

  for(cnt=0;cnt<3;cnt++)
    {
      PWM_enableTripZoneSrc(obj->pwmHandle[cnt],PWM_TripZoneSrc_CycleByCycle_TZ6_NOT);

//    PWM_enableTripZoneSrc(obj->pwmHandle[cnt],PWM_TripZoneSrc_CycleByCycle_TZ2_NOT);

      // What do we want the OST/CBC events to do?
      // TZA events can force EPWMxA
      // TZB events can force EPWMxB

      PWM_setTripZoneState_TZA(obj->pwmHandle[cnt],PWM_TripZoneState_EPWM_Low);
      PWM_setTripZoneState_TZB(obj->pwmHandle[cnt],PWM_TripZoneState_EPWM_Low);
    }

  return;
} // end of HAL_setupFaults() function


HAL_Handle HAL_init(void *pMemory,const size_t numBytes)
{
  uint_least8_t cnt;
  HAL_Handle handle;
  HAL_Obj *obj;


  if(numBytes < sizeof(HAL_Obj))
    return((HAL_Handle)NULL);


  // assign the handle
  handle = (HAL_Handle)pMemory;


  // assign the object
  obj = (HAL_Obj *)handle;


  // initialize the watchdog driver
  obj->wdogHandle = WDOG_init((void *)WDOG_BASE_ADDR,sizeof(WDOG_Obj));


  // disable watchdog
  HAL_disableWdog(handle);


  // initialize the ADC
  obj->adcHandle = ADC_init((void *)ADC_BASE_ADDR,sizeof(ADC_Obj));


  // initialize the clock handle
  obj->clkHandle = CLK_init((void *)CLK_BASE_ADDR,sizeof(CLK_Obj));


  // initialize the CPU handle
  obj->cpuHandle = CPU_init(&cpu,sizeof(cpu));


  // initialize the FLASH handle
  obj->flashHandle = FLASH_init((void *)FLASH_BASE_ADDR,sizeof(FLASH_Obj));


  // initialize the GPIO handle
  obj->gpioHandle = GPIO_init((void *)GPIO_BASE_ADDR,sizeof(GPIO_Obj));


  // initialize the current offset estimator handles
  for(cnt=0;cnt<USER_NUM_CURRENT_SENSORS;cnt++)
    {
      obj->offsetHandle_I[cnt] = OFFSET_init(&obj->offset_I[cnt],sizeof(obj->offset_I[cnt]));
    }


  // initialize the voltage offset estimator handles
  for(cnt=0;cnt<USER_NUM_VOLTAGE_SENSORS;cnt++)
    {
      obj->offsetHandle_V[cnt] = OFFSET_init(&obj->offset_V[cnt],sizeof(obj->offset_V[cnt]));
    }


  // initialize the oscillator handle
  obj->oscHandle = OSC_init((void *)OSC_BASE_ADDR,sizeof(OSC_Obj));


  // initialize the PIE handle
  obj->pieHandle = PIE_init((void *)PIE_BASE_ADDR,sizeof(PIE_Obj));


  // initialize the PLL handle
  obj->pllHandle = PLL_init((void *)PLL_BASE_ADDR,sizeof(PLL_Obj));

  // initialize the SPIA handle
  obj->spiAHandle = SPI_init((void *)SPIA_BASE_ADDR,sizeof(SPI_Obj));

  // initialize PWM handle
  obj->pwmHandle[0] = PWM_init((void *)PWM_ePWM1_BASE_ADDR,sizeof(PWM_Obj));
  obj->pwmHandle[1] = PWM_init((void *)PWM_ePWM2_BASE_ADDR,sizeof(PWM_Obj));
  obj->pwmHandle[2] = PWM_init((void *)PWM_ePWM3_BASE_ADDR,sizeof(PWM_Obj));


  // initialize power handle
  obj->pwrHandle = PWR_init((void *)PWR_BASE_ADDR,sizeof(PWR_Obj));


  // initialize timer drivers
  obj->timerHandle[0] = TIMER_init((void *)TIMER0_BASE_ADDR,sizeof(TIMER_Obj));
  obj->timerHandle[1] = TIMER_init((void *)TIMER1_BASE_ADDR,sizeof(TIMER_Obj));
  obj->timerHandle[2] = TIMER_init((void *)TIMER2_BASE_ADDR,sizeof(TIMER_Obj));


  // initialize drv8353 interface
  obj->drv8353Handle = DRV8353_init(&obj->drv8353,sizeof(obj->drv8353));

  return(handle);
} // end of HAL_init() function

//TODO: HAL_setParams
void HAL_setParams(HAL_Handle handle,const USER_Params *pUserParams)
{
  uint_least8_t cnt;
  HAL_Obj *obj = (HAL_Obj *)handle;
  _iq beta_lp_pu = _IQ(pUserParams->offsetPole_rps/(float_t)pUserParams->ctrlFreq_Hz);


  HAL_setNumCurrentSensors(handle,pUserParams->numCurrentSensors);
  HAL_setNumVoltageSensors(handle,pUserParams->numVoltageSensors);


  for(cnt=0;cnt<HAL_getNumCurrentSensors(handle);cnt++)
    {
      HAL_setOffsetBeta_lp_pu(handle,HAL_SensorType_Current,cnt,beta_lp_pu);
      HAL_setOffsetInitCond(handle,HAL_SensorType_Current,cnt,_IQ(0.0));
      HAL_setOffsetValue(handle,HAL_SensorType_Current,cnt,_IQ(0.0));
    }


  for(cnt=0;cnt<HAL_getNumVoltageSensors(handle);cnt++)
    {
      HAL_setOffsetBeta_lp_pu(handle,HAL_SensorType_Voltage,cnt,beta_lp_pu);
      HAL_setOffsetInitCond(handle,HAL_SensorType_Voltage,cnt,_IQ(0.0));
      HAL_setOffsetValue(handle,HAL_SensorType_Voltage,cnt,_IQ(0.0));
    }


  // disable global interrupts
  CPU_disableGlobalInts(obj->cpuHandle);


  // disable cpu interrupts
  CPU_disableInts(obj->cpuHandle);


  // clear cpu interrupt flags
  CPU_clearIntFlags(obj->cpuHandle);


  // setup the clocks
  HAL_setupClks(handle);


  // Setup the PLL
  HAL_setupPll(handle,PLL_ClkFreq_60_MHz);


  // setup the PIE
  HAL_setupPie(handle);


  // run the device calibration
  HAL_cal(handle);


  // setup the peripheral clocks
  HAL_setupPeripheralClks(handle);


  // setup the GPIOs
  HAL_setupGpios(handle);


  // setup the flash
  HAL_setupFlash(handle);


  // setup the ADCs
  HAL_setupAdcs(handle);


  // setup the PWMs
  HAL_setupPwms(handle,
                (float_t)pUserParams->systemFreq_MHz,
                pUserParams->pwmPeriod_usec,
                USER_NUM_PWM_TICKS_PER_ISR_TICK);

  // setup the spiA
  HAL_setupSpiA(handle);

  // setup the timers
  HAL_setupTimers(handle,
                  (float_t)pUserParams->systemFreq_MHz);


  // setup the drv8353 interface
  HAL_setupGate(handle);


  // set the default current bias
 {
   uint_least8_t cnt;
   _iq bias = _IQ12mpy(ADC_dataBias,_IQ(pUserParams->current_sf));
   
   for(cnt=0;cnt<HAL_getNumCurrentSensors(handle);cnt++)
     {
       HAL_setBias(handle,HAL_SensorType_Current,cnt,bias);
     }
 }


  //  set the current scale factor
 {
   _iq current_sf = _IQ(pUserParams->current_sf);

  HAL_setCurrentScaleFactor(handle,current_sf);
 }


  // set the default voltage bias
 {
   uint_least8_t cnt;
   _iq bias = _IQ(0.0);
   
   for(cnt=0;cnt<HAL_getNumVoltageSensors(handle);cnt++)
     {
       HAL_setBias(handle,HAL_SensorType_Voltage,cnt,bias);
     }
 }


  //  set the voltage scale factor
 {
   _iq voltage_sf = _IQ(pUserParams->voltage_sf);

  HAL_setVoltageScaleFactor(handle,voltage_sf);
 }

 return;
} // end of HAL_setParams() function


void HAL_setupAdcs(HAL_Handle handle)
{
  HAL_Obj *obj = (HAL_Obj *)handle;


  // disable the ADCs
  ADC_disable(obj->adcHandle);


  // power up the bandgap circuit
  ADC_enableBandGap(obj->adcHandle);


  // set the ADC voltage reference source to internal 
  ADC_setVoltRefSrc(obj->adcHandle,ADC_VoltageRefSrc_Int);


  // enable the ADC reference buffers
  ADC_enableRefBuffers(obj->adcHandle);


  // Set main clock scaling factor (max45MHz clock for the ADC module)
  ADC_setDivideSelect(obj->adcHandle,ADC_DivideSelect_ClkIn_by_2);

  // power up the ADCs
  ADC_powerUp(obj->adcHandle);


  // enable the ADCs
  ADC_enable(obj->adcHandle);


  // set the ADC interrupt pulse generation to prior
  ADC_setIntPulseGenMode(obj->adcHandle,ADC_IntPulseGenMode_Prior);


  // set the temperature sensor source to external
  ADC_setTempSensorSrc(obj->adcHandle,ADC_TempSensorSrc_Ext);


  // configure the interrupt sources
  ADC_disableInt(obj->adcHandle,ADC_IntNumber_1);
  ADC_setIntMode(obj->adcHandle,ADC_IntNumber_1,ADC_IntMode_ClearFlag);
  ADC_setIntSrc(obj->adcHandle,ADC_IntNumber_1,ADC_IntSrc_EOC7);


  //configure the SOCs for drv8353evm
  // sample the first sample twice due to errata sprz342f
  // ISEN_A
  ADC_setSocChanNumber(obj->adcHandle,ADC_SocNumber_0,ADC_SocChanNumber_B3);
  ADC_setSocTrigSrc(obj->adcHandle,ADC_SocNumber_0,ADC_SocTrigSrc_EPWM1_ADCSOCA);
  ADC_setSocSampleDelay(obj->adcHandle,ADC_SocNumber_0,ADC_SocSampleDelay_9_cycles);

  // ISEN_A
  ADC_setSocChanNumber(obj->adcHandle,ADC_SocNumber_1,ADC_SocChanNumber_B3);
  ADC_setSocTrigSrc(obj->adcHandle,ADC_SocNumber_1,ADC_SocTrigSrc_EPWM1_ADCSOCA);
  ADC_setSocSampleDelay(obj->adcHandle,ADC_SocNumber_1,ADC_SocSampleDelay_9_cycles);

  // ISEN_B
  ADC_setSocChanNumber(obj->adcHandle,ADC_SocNumber_2,ADC_SocChanNumber_B1);
  ADC_setSocTrigSrc(obj->adcHandle,ADC_SocNumber_2,ADC_SocTrigSrc_EPWM1_ADCSOCA);
  ADC_setSocSampleDelay(obj->adcHandle,ADC_SocNumber_2,ADC_SocSampleDelay_9_cycles);

  // ISEN_C
  ADC_setSocChanNumber(obj->adcHandle,ADC_SocNumber_3,ADC_SocChanNumber_A0);
  ADC_setSocTrigSrc(obj->adcHandle,ADC_SocNumber_3,ADC_SocTrigSrc_EPWM1_ADCSOCA);
  ADC_setSocSampleDelay(obj->adcHandle,ADC_SocNumber_3,ADC_SocSampleDelay_9_cycles);

  // VSEN_A
  ADC_setSocChanNumber(obj->adcHandle,ADC_SocNumber_4,ADC_SocChanNumber_A7);
  ADC_setSocTrigSrc(obj->adcHandle,ADC_SocNumber_4,ADC_SocTrigSrc_EPWM1_ADCSOCA);
  ADC_setSocSampleDelay(obj->adcHandle,ADC_SocNumber_4,ADC_SocSampleDelay_9_cycles);

  // VSEN_B
  ADC_setSocChanNumber(obj->adcHandle,ADC_SocNumber_5,ADC_SocChanNumber_A3);
  ADC_setSocTrigSrc(obj->adcHandle,ADC_SocNumber_5,ADC_SocTrigSrc_EPWM1_ADCSOCA);
  ADC_setSocSampleDelay(obj->adcHandle,ADC_SocNumber_5,ADC_SocSampleDelay_9_cycles);

  // VSEN_C
  ADC_setSocChanNumber(obj->adcHandle,ADC_SocNumber_6,ADC_SocChanNumber_A1);
  ADC_setSocTrigSrc(obj->adcHandle,ADC_SocNumber_6,ADC_SocTrigSrc_EPWM1_ADCSOCA);
  ADC_setSocSampleDelay(obj->adcHandle,ADC_SocNumber_6,ADC_SocSampleDelay_9_cycles);

  // V_PVDD
  ADC_setSocChanNumber(obj->adcHandle,ADC_SocNumber_7,ADC_SocChanNumber_A6);
  ADC_setSocTrigSrc(obj->adcHandle,ADC_SocNumber_7,ADC_SocTrigSrc_EPWM1_ADCSOCA);
  ADC_setSocSampleDelay(obj->adcHandle,ADC_SocNumber_7,ADC_SocSampleDelay_16_cycles);

  // V_DeviceID
  // Potentiometer // Configure it so that ADCINT1 will trigger a potentiometer conversion
  ADC_setSocChanNumber(obj->adcHandle,ADC_SocNumber_8,ADC_SocChanNumber_B4);
  ADC_setupSocTrigSrc(obj->adcHandle, ADC_SocNumber_8, ADC_Int1TriggersSOC);
  ADC_setSocSampleDelay(obj->adcHandle,ADC_SocNumber_8,ADC_SocSampleDelay_9_cycles);

  return;
} // end of HAL_setupAdcs() function


void HAL_setupClks(HAL_Handle handle)
{
  HAL_Obj *obj = (HAL_Obj *)handle;


  // enable internal oscillator 1
  CLK_enableOsc1(obj->clkHandle);

  // set the oscillator source
  CLK_setOscSrc(obj->clkHandle,CLK_OscSrc_Internal);

  // disable the external clock in
  CLK_disableClkIn(obj->clkHandle);

  // disable the crystal oscillator
  CLK_disableCrystalOsc(obj->clkHandle);

  // disable oscillator 2
  CLK_disableOsc2(obj->clkHandle);

  // set the low speed clock prescaler
//  CLK_setLowSpdPreScaler(obj->clkHandle,CLK_LowSpdPreScaler_SysClkOut_by_4);
  CLK_setLowSpdPreScaler(obj->clkHandle,CLK_LowSpdPreScaler_SysClkOut_by_2);

  // set the clock out prescaler
  CLK_setClkOutPreScaler(obj->clkHandle,CLK_ClkOutPreScaler_SysClkOut_by_1);

  return;
} // end of HAL_setupClks() function


void HAL_setupFlash(HAL_Handle handle)
{
  HAL_Obj *obj = (HAL_Obj *)handle;


  FLASH_enablePipelineMode(obj->flashHandle);

  FLASH_setNumPagedReadWaitStates(obj->flashHandle,FLASH_NumPagedWaitStates_2);

  FLASH_setNumRandomReadWaitStates(obj->flashHandle,FLASH_NumRandomWaitStates_2);

  FLASH_setOtpWaitStates(obj->flashHandle,FLASH_NumOtpWaitStates_3);

  FLASH_setStandbyWaitCount(obj->flashHandle,FLASH_STANDBY_WAIT_COUNT_DEFAULT);

  FLASH_setActiveWaitCount(obj->flashHandle,FLASH_ACTIVE_WAIT_COUNT_DEFAULT);

  return;
} // HAL_setupFlash() function


void HAL_setupGate(HAL_Handle handle)
{
  HAL_Obj *obj = (HAL_Obj *)handle;

  DRV8353_setSpiHandle(obj->drv8353Handle, obj->spiAHandle);
  DRV8353_setGpioHandle(obj->drv8353Handle, obj->gpioHandle);
  DRV8353_setGpioNumber(obj->drv8353Handle, GPIO_Number_34);		// Enable Gate of DRV8353

  return;
} // HAL_setupGate() function


void HAL_setupGpios(HAL_Handle handle)
{
  HAL_Obj *obj = (HAL_Obj *)handle;

  // PWMA_H
  GPIO_setMode(obj->gpioHandle,GPIO_Number_0,GPIO_0_Mode_EPWM1A);

  // PWMA_L
  GPIO_setMode(obj->gpioHandle,GPIO_Number_1,GPIO_1_Mode_EPWM1B);

  // PWMB_H
  GPIO_setMode(obj->gpioHandle,GPIO_Number_2,GPIO_2_Mode_EPWM2A);

  // PWMB_L
  GPIO_setMode(obj->gpioHandle,GPIO_Number_3,GPIO_3_Mode_EPWM2B);
  
  // PWMC_H
  GPIO_setMode(obj->gpioHandle,GPIO_Number_4,GPIO_4_Mode_EPWM3A);

  // PWMC_L
  GPIO_setMode(obj->gpioHandle,GPIO_Number_5,GPIO_5_Mode_EPWM3B);

  // HALL_C
  GPIO_setMode(obj->gpioHandle,GPIO_Number_6,GPIO_6_Mode_GeneralPurpose);

  // DRV8353 SCS/GAIN
  GPIO_setMode(obj->gpioHandle,GPIO_Number_7,GPIO_7_Mode_GeneralPurpose);
  GPIO_setHigh(obj->gpioHandle,GPIO_Number_7);
  GPIO_setDirection(obj->gpioHandle,GPIO_Number_7,GPIO_Direction_Output);

  // HALL_B
  GPIO_setMode(obj->gpioHandle,GPIO_Number_12,GPIO_12_Mode_GeneralPurpose);

  // SPI_SDI if JP4 is soldered, No Connection if JP4 is not soldered
  GPIO_setMode(obj->gpioHandle,GPIO_Number_16,GPIO_16_Mode_SPISIMOA);

  // SPI_SDO if JP6 is soldered, No Connection if JP6 is not soldered
  GPIO_setMode(obj->gpioHandle,GPIO_Number_17,GPIO_17_Mode_SPISOMIA);
  GPIO_setPullUp(obj->gpioHandle, GPIO_Number_17, GPIO_PullUp_Disable);

  // SPI_CLK
  GPIO_setMode(obj->gpioHandle,GPIO_Number_18,GPIO_18_Mode_SPICLKA);

  // HALL_A->ECAP1
  GPIO_setMode(obj->gpioHandle,GPIO_Number_19,GPIO_19_Mode_GeneralPurpose);

  // SCI_RX
  GPIO_setMode(obj->gpioHandle,GPIO_Number_28,GPIO_28_Mode_SCIRXDA);

  // SCI_TX
  GPIO_setMode(obj->gpioHandle,GPIO_Number_29,GPIO_29_Mode_SCITXDA);

  // N/A
  GPIO_setMode(obj->gpioHandle,GPIO_Number_32,GPIO_32_Mode_GeneralPurpose);
  GPIO_setLow(obj->gpioHandle,GPIO_Number_32);
  GPIO_setDirection(obj->gpioHandle,GPIO_Number_32,GPIO_Direction_Output);

  // DRV8353_LED
  GPIO_setMode(obj->gpioHandle,GPIO_Number_33,GPIO_33_Mode_GeneralPurpose);
  GPIO_setHigh(obj->gpioHandle,GPIO_Number_33);
  GPIO_setDirection(obj->gpioHandle,GPIO_Number_33,GPIO_Direction_Output);

  // DRV8353 Enable Gate
  GPIO_setMode(obj->gpioHandle,GPIO_Number_34,GPIO_34_Mode_GeneralPurpose);
  GPIO_setLow(obj->gpioHandle,GPIO_Number_34);
  GPIO_setDirection(obj->gpioHandle,GPIO_Number_34,GPIO_Direction_Output);
  GPIO_setLow(obj->gpioHandle,GPIO_Number_34);      // Disable DRV83533 First

  // JTAG
  GPIO_setMode(obj->gpioHandle,GPIO_Number_35,GPIO_35_Mode_JTAG_TDI);
  GPIO_setMode(obj->gpioHandle,GPIO_Number_36,GPIO_36_Mode_JTAG_TMS);
  GPIO_setMode(obj->gpioHandle,GPIO_Number_37,GPIO_37_Mode_JTAG_TDO);
  GPIO_setMode(obj->gpioHandle,GPIO_Number_38,GPIO_38_Mode_JTAG_TCK);

  return;
}  // end of HAL_setupGpios() function

void HAL_setupPie(HAL_Handle handle)
{
  HAL_Obj *obj = (HAL_Obj *)handle;


  PIE_disable(obj->pieHandle);

  PIE_disableAllInts(obj->pieHandle);

  PIE_clearAllInts(obj->pieHandle);

  PIE_clearAllFlags(obj->pieHandle);

  PIE_setDefaultIntVectorTable(obj->pieHandle);

  PIE_enable(obj->pieHandle);

  return;
} // end of HAL_setupPie() function


void HAL_setupPeripheralClks(HAL_Handle handle)
{
  HAL_Obj *obj = (HAL_Obj *)handle;


  CLK_enableAdcClock(obj->clkHandle);

  CLK_enableCompClock(obj->clkHandle,CLK_CompNumber_1);
  CLK_enableCompClock(obj->clkHandle,CLK_CompNumber_2);
  CLK_enableCompClock(obj->clkHandle,CLK_CompNumber_3);

  CLK_enableEcap1Clock(obj->clkHandle);

  CLK_enablePwmClock(obj->clkHandle,PWM_Number_1);
  CLK_enablePwmClock(obj->clkHandle,PWM_Number_2);
  CLK_enablePwmClock(obj->clkHandle,PWM_Number_3);
  CLK_enablePwmClock(obj->clkHandle,PWM_Number_4);

  CLK_disableHrPwmClock(obj->clkHandle);

  CLK_disableI2cClock(obj->clkHandle);

  CLK_enableSciaClock(obj->clkHandle);
  CLK_enableSpiaClock(obj->clkHandle);
  CLK_enableTbClockSync(obj->clkHandle);

  return;
} // end of HAL_setupPeripheralClks() function


void HAL_setupPll(HAL_Handle handle,const PLL_ClkFreq_e clkFreq)
{
  HAL_Obj *obj = (HAL_Obj *)handle;


  // make sure PLL is not running in limp mode
  if(PLL_getClkStatus(obj->pllHandle) != PLL_ClkStatus_Normal)
    {
      // reset the clock detect
      PLL_resetClkDetect(obj->pllHandle);

      // ???????
      asm("        ESTOP0");
    }


  // Divide Select must be ClkIn/4 before the clock rate can be changed
  if(PLL_getDivideSelect(obj->pllHandle) != PLL_DivideSelect_ClkIn_by_4)
    {
      PLL_setDivideSelect(obj->pllHandle,PLL_DivideSelect_ClkIn_by_4);
    }


  if(PLL_getClkFreq(obj->pllHandle) != clkFreq)
    {
      // disable the clock detect
      PLL_disableClkDetect(obj->pllHandle);

      // set the clock rate
      PLL_setClkFreq(obj->pllHandle,clkFreq);
    }


  // wait until locked
  while(PLL_getLockStatus(obj->pllHandle) != PLL_LockStatus_Done) {}


  // enable the clock detect
  PLL_enableClkDetect(obj->pllHandle);


  // set divide select to ClkIn/2 to get desired clock rate
  // NOTE: clock must be locked before setting this register
  PLL_setDivideSelect(obj->pllHandle,PLL_DivideSelect_ClkIn_by_2);

  return;
} // end of HAL_setupPll() function


void HAL_setupPwms(HAL_Handle handle,
                   const float_t systemFreq_MHz,
                   const float_t pwmPeriod_usec,
                   const uint_least16_t numPwmTicksPerIsrTick)
{
  HAL_Obj   *obj = (HAL_Obj *)handle;
  uint16_t   halfPeriod_cycles = (uint16_t)(systemFreq_MHz*pwmPeriod_usec) >> 1;
  uint_least8_t    cnt;


  // turns off the outputs of the EPWM peripherals which will put the power switches
  // into a high impedance state.
  PWM_setOneShotTrip(obj->pwmHandle[PWM_Number_1]);
  PWM_setOneShotTrip(obj->pwmHandle[PWM_Number_2]);
  PWM_setOneShotTrip(obj->pwmHandle[PWM_Number_3]);
  // first step to synchronize the pwms
  CLK_disableTbClockSync(obj->clkHandle);

  for(cnt=0;cnt<3;cnt++)
    {
      // setup the Time-Base Control Register (TBCTL)
      PWM_setCounterMode(obj->pwmHandle[cnt],PWM_CounterMode_UpDown);
      PWM_disableCounterLoad(obj->pwmHandle[cnt]);
      PWM_setPeriodLoad(obj->pwmHandle[cnt],PWM_PeriodLoad_Immediate);
      PWM_setSyncMode(obj->pwmHandle[cnt],PWM_SyncMode_EPWMxSYNC);
      PWM_setHighSpeedClkDiv(obj->pwmHandle[cnt],PWM_HspClkDiv_by_1);
      PWM_setClkDiv(obj->pwmHandle[cnt],PWM_ClkDiv_by_1);
      PWM_setPhaseDir(obj->pwmHandle[cnt],PWM_PhaseDir_CountUp);
      PWM_setRunMode(obj->pwmHandle[cnt],PWM_RunMode_FreeRun);

      // setup the Timer-Based Phase Register (TBPHS)
      PWM_setPhase(obj->pwmHandle[cnt],0);

      // setup the Time-Base Counter Register (TBCTR)
      PWM_setCount(obj->pwmHandle[cnt],0);

      // setup the Time-Base Period Register (TBPRD)
      // set to zero initially
      PWM_setPeriod(obj->pwmHandle[cnt],0);

      // setup the Counter-Compare Control Register (CMPCTL)
      PWM_setLoadMode_CmpA(obj->pwmHandle[cnt],PWM_LoadMode_Zero);
      PWM_setLoadMode_CmpB(obj->pwmHandle[cnt],PWM_LoadMode_Zero);
      PWM_setShadowMode_CmpA(obj->pwmHandle[cnt],PWM_ShadowMode_Shadow);
      PWM_setShadowMode_CmpB(obj->pwmHandle[cnt],PWM_ShadowMode_Immediate);

      // setup the Action-Qualifier Output A Register (AQCTLA) 
      PWM_setActionQual_CntUp_CmpA_PwmA(obj->pwmHandle[cnt],PWM_ActionQual_Set);
      PWM_setActionQual_CntDown_CmpA_PwmA(obj->pwmHandle[cnt],PWM_ActionQual_Clear);

      // setup the Dead-Band Generator Control Register (DBCTL)
      PWM_setDeadBandOutputMode(obj->pwmHandle[cnt],PWM_DeadBandOutputMode_EPWMxA_Rising_EPWMxB_Falling);
      PWM_setDeadBandPolarity(obj->pwmHandle[cnt],PWM_DeadBandPolarity_EPWMxB_Inverted);

      // setup the Dead-Band Rising Edge Delay Register (DBRED)
      PWM_setDeadBandRisingEdgeDelay(obj->pwmHandle[cnt],HAL_PWM_DBRED_CNT);

      // setup the Dead-Band Falling Edge Delay Register (DBFED)
      PWM_setDeadBandFallingEdgeDelay(obj->pwmHandle[cnt],HAL_PWM_DBFED_CNT);
      // setup the PWM-Chopper Control Register (PCCTL)
      PWM_disableChopping(obj->pwmHandle[cnt]);

      // setup the Trip Zone Select Register (TZSEL)
      PWM_disableTripZones(obj->pwmHandle[cnt]);
    }


  // setup the Event Trigger Selection Register (ETSEL)
  PWM_disableInt(obj->pwmHandle[PWM_Number_1]);
  PWM_setSocAPulseSrc(obj->pwmHandle[PWM_Number_1],PWM_SocPulseSrc_CounterEqualZero);
  PWM_enableSocAPulse(obj->pwmHandle[PWM_Number_1]);
  

  // setup the Event Trigger Prescale Register (ETPS)
  if(numPwmTicksPerIsrTick == 3)
    {
      PWM_setIntPeriod(obj->pwmHandle[PWM_Number_1],PWM_IntPeriod_ThirdEvent);
      PWM_setSocAPeriod(obj->pwmHandle[PWM_Number_1],PWM_SocPeriod_ThirdEvent);
    }
  else if(numPwmTicksPerIsrTick == 2)
    {
      PWM_setIntPeriod(obj->pwmHandle[PWM_Number_1],PWM_IntPeriod_SecondEvent);
      PWM_setSocAPeriod(obj->pwmHandle[PWM_Number_1],PWM_SocPeriod_SecondEvent);
    }
  else
    {
      PWM_setIntPeriod(obj->pwmHandle[PWM_Number_1],PWM_IntPeriod_FirstEvent);
      PWM_setSocAPeriod(obj->pwmHandle[PWM_Number_1],PWM_SocPeriod_FirstEvent);
    }


  // setup the Event Trigger Clear Register (ETCLR)
  PWM_clearIntFlag(obj->pwmHandle[PWM_Number_1]);
  PWM_clearSocAFlag(obj->pwmHandle[PWM_Number_1]);


  // since the PWM is configured as an up/down counter, the period register is set to one-half 
  // of the desired PWM period
  PWM_setPeriod(obj->pwmHandle[PWM_Number_1],halfPeriod_cycles);
  PWM_setPeriod(obj->pwmHandle[PWM_Number_2],halfPeriod_cycles);
  PWM_setPeriod(obj->pwmHandle[PWM_Number_3],halfPeriod_cycles);

  // last step to synchronize the pwms
  CLK_enableTbClockSync(obj->clkHandle);

  return;
}  // end of HAL_setupPwms() function


void HAL_setupSpiA(HAL_Handle handle)
{
  HAL_Obj   *obj = (HAL_Obj *)handle;

  SPI_reset(obj->spiAHandle);
  SPI_setMode(obj->spiAHandle,SPI_Mode_Master);
  SPI_setClkPolarity(obj->spiAHandle,SPI_ClkPolarity_OutputRisingEdge_InputFallingEdge);
  SPI_enableTx(obj->spiAHandle);
  SPI_enableTxFifoEnh(obj->spiAHandle);
  SPI_enableTxFifo(obj->spiAHandle);
  SPI_setTxDelay(obj->spiAHandle,0x0010);
  SPI_setBaudRate(obj->spiAHandle,(SPI_BaudRate_e)(0x0010));
  SPI_setCharLength(obj->spiAHandle,SPI_CharLength_16_Bits);
  SPI_setSuspend(obj->spiAHandle,SPI_TxSuspend_free);
  SPI_enable(obj->spiAHandle);

  return;
}  // end of HAL_setupSpiA() function


void HAL_setupTimers(HAL_Handle handle,const float_t systemFreq_MHz)
{
  HAL_Obj  *obj = (HAL_Obj *)handle;
  uint32_t  timerPeriod_0p5ms = (uint32_t)(systemFreq_MHz * (float_t)500.0) - 1;
  uint32_t  timerPeriod_10ms = (uint32_t)(systemFreq_MHz * (float_t)10000.0) - 1;

  // use timer 0 for frequency diagnostics
  TIMER_setDecimationFactor(obj->timerHandle[0],0);
  TIMER_setEmulationMode(obj->timerHandle[0],TIMER_EmulationMode_RunFree);
  TIMER_setPeriod(obj->timerHandle[0],timerPeriod_0p5ms);
  TIMER_setPreScaler(obj->timerHandle[0],0);

  // use timer 1 for CPU usage diagnostics
  TIMER_setDecimationFactor(obj->timerHandle[1],0);
  TIMER_setEmulationMode(obj->timerHandle[1],TIMER_EmulationMode_RunFree);
  TIMER_setPeriod(obj->timerHandle[1],timerPeriod_10ms);
  TIMER_setPreScaler(obj->timerHandle[1],0);

  // use timer 2 for CPU time diagnostics
  TIMER_setDecimationFactor(obj->timerHandle[2],0);
  TIMER_setEmulationMode(obj->timerHandle[2],TIMER_EmulationMode_RunFree);
  TIMER_setPeriod(obj->timerHandle[2],0xFFFFFFFF);
  TIMER_setPreScaler(obj->timerHandle[2],0);

  return;
}  // end of HAL_setupTimers() function


void HAL_writeDrvData(HAL_Handle handle, DRV_SPI_8353_Vars_t *Spi_8353_Vars)
{
  HAL_Obj  *obj = (HAL_Obj *)handle;

  DRV8353_writeData(obj->drv8353Handle,Spi_8353_Vars);
  
  return;
}  // end of HAL_writeDrvData() function


void HAL_readDrvData(HAL_Handle handle, DRV_SPI_8353_Vars_t *Spi_8353_Vars)
{
  HAL_Obj  *obj = (HAL_Obj *)handle;

  DRV8353_readData(obj->drv8353Handle,Spi_8353_Vars);
  
  return;
}  // end of HAL_readDrvData() function


void HAL_setupDrvSpi(HAL_Handle handle, DRV_SPI_8353_Vars_t *Spi_8353_Vars)
{
  HAL_Obj  *obj = (HAL_Obj *)handle;

  DRV8353_setupSpi(obj->drv8353Handle,Spi_8353_Vars);

  return;
}  // end of HAL_setupDrvSpi() function


void HAL_setDacParameters(HAL_Handle handle, HAL_DacData_t *pDacData)
{
	HAL_Obj *obj = (HAL_Obj *)handle;

	pDacData->PeriodMax = PWMDAC_getPeriod(obj->pwmDacHandle[PWMDAC_Number_1]);

	pDacData->offset[0] = _IQ(0.5);
	pDacData->offset[1] = _IQ(0.5);
	pDacData->offset[2] = _IQ(0.0);
	pDacData->offset[3] = _IQ(0.0);

	pDacData->gain[0] = _IQ(1.0);
	pDacData->gain[1] = _IQ(1.0);
	pDacData->gain[2] = _IQ(1.0);
	pDacData->gain[3] = _IQ(1.0);

	return;
}	//end of HAL_setDacParameters() function

// end of file