• State TI Thinks Resolved
  • Locked Locked
  • Replies 5 replies
  • Answers 2 answers
  • Subscribers 63 subscribers
  • Views 157 views
  • Users 0 members are here
Support feedback
Options
Options
Similar topics

This thread has been locked.

If you have a related question, please click the "Ask a related question" button in the top right corner. The newly created question will be automatically linked to this question.

Original question:

[FAQ] List of FAQs for TPS650320-Q1, TPS650330-Q1, TPS650331-Q1, TPS650332-Q1, TPS650333-Q1, TPS650350-Q1

TPS650320-Q1: TPS650320-Q1 default output voltage

user5789841
Intellectual 315 points
Part Number: TPS650320-Q1
Other Parts Discussed in Thread: TPS650352-Q1

Tool/software:

Hello TI Team, 

I can't find the completed datasheet in TI website, could you share me the completed datasheet to me ?

By the way  , I would like to check if I can directly use this device supply to MCU?

I am not sure whether it can default output 3.3V voltage supply to MCU directly without any configuration.......and what does I2C's function of this chip? 

Thanks!

  • 0
    TI__Guru 74266 points

    Hi,

    You can request the full datasheet from the product folder of the device, there is a section: 

    Here is direct link to make the request. The datasheet is only available under NDA so please check if you have active NDA with TI. https://www.ti.com/drr/opn/TPS65033X-Q1-DESIGN-DOCS 

    Regards,

    Katie

  • 0 in reply to Katie Pier
    Intellectual 315 points

    Hi ,

    I didn't get the completed datasheet until now , could help to check the default output voltage of Bulk 1 ,2, 3 and LDO for below ICs:

    TPS650320-Q1

    •  Default output voltage of Bulk 1 : xxx V
    •  Default output voltage of Bulk 2 : xxx V
    •  Default output voltage of Bulk 3 : xxx V
    •  Default output voltage of LDO 1 : xxx V

    TPS65036x-Q1

    •  Default output voltage of Bulk 1 : xxx V
    •  Default output voltage of Bulk 2 : xxx V
    •  Default output voltage of Bulk 3 : xxx V
    •  Default output voltage of LDO 1 : xxx V

    TPS650352-Q1

    •  Default output voltage of Bulk 1 : xxx V
    •  Default output voltage of Bulk 2 : xxx V
    •  Default output voltage of Bulk 3 : xxx V
    •  Default output voltage of LDO 1 : xxx V

    Thanks!

  • 0 in reply to user5789841
    TI__Guru 74266 points

    Did you submit the request at the link I provided? I cannot share this in public forum. What mail did you use to submit the request - I could not find one that matched the email you have associated with your myTI account. 

    Regards,

    Katie

  • 0 in reply to Katie Pier
    Intellectual 315 points

    Hi,

    Yes, I have submitted the request !

    Would pls. help to answer my above question first? this is important to me , because I plan do the MCU's power from the below ICs directly, I need ensure my MCU is working first  , then it can configure the other output voltage of ICs.

    TPS650320-Q1

    •  Default output voltage of Bulk 1 : xxx V
    •  Default output voltage of Bulk 2 : xxx V
    •  Default output voltage of Bulk 3 : xxx V
    •  Default output voltage of LDO 1 : xxx V

    TPS65036x-Q1

    •  Default output voltage of Bulk 1 : xxx V
    •  Default output voltage of Bulk 2 : xxx V
    •  Default output voltage of Bulk 3 : xxx V
    •  Default output voltage of LDO 1 : xxx V

    TPS650352-Q1

    •  Default output voltage of Bulk 1 : xxx V
    •  Default output voltage of Bulk 2 : xxx V
    •  Default output voltage of Bulk 3 : xxx V
    •  Default output voltage of LDO 1 : xxx V

    Thanks!

  • 0 in reply to user5789841
    TI__Guru 74266 points

    Hi,

    I see your request now and believe it should be approved. See if you can access the datasheet. 

    For your request about voltages, it depends on the NVM used, which differs depending on the full part number OPN of the device. The Camera PMIC selection guide might be helpful here: www.ti.com/lit/pdf/slvaey0b section 2 has a good table with the output voltages and sequencing. 

    Regards,

    Katie