Texas Instruments (TI) Power management support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search power management IC content or ask technical support questions on everything from linear and DC/DC switching regulators to battery management and LED drivers. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions

  • [FAQ] TPS51200: TPS51200 Pin-to-Pin Compatibility

    Part Number: TPS51200 Other Parts Discussed in Thread: TPS51206 , , , TPS51216-EP , TPS51216 , , TPS51100 Which parts in the TPS51200 family ( TPS51200, TPS51200-EP, TPS51200-Q1, TPS51200A-Q1, TPS51206, TPS51216, and TPS51216-EP ) are pin-to-pin compatible…

  • [FAQ] BQ76952: BQ76952 functional safety related documents

    Part Number: BQ76952 How/where to request functional safety related documents for BQ76952 series ic. In battery management system seminar presentaion ( https://www.ti.com/lit/ml/slyp813/slyp813.pdf?ts=1643809126117&ref_url=https%253A%252F%252Fwww.ti…

  • [FAQ] TPS62913: How do I ensure my layout results in the best noise and ripple performance possible when using the TPS62912 and TPS62913?

    Part Number: TPS62913 Other Parts Discussed in Thread: TPS62912 I need to ensure that the power supply has the lowest noise and ripple possible, and would like to ensure that my layout does not cause any issues. Any tips?

  • [FAQ] UCC21530: Can UCC21530 and UCC21540 DWK packages be used in 800V systems?

    Part Number: UCC21530 Other Parts Discussed in Thread: UCC21540 As 800 V systems are becoming more common it is important to not only consider the voltage from the primary to secondary side of a driver, but also the channel to channel voltage, at least…

  • [FAQ] Can I use LMG1210 with a bipolar supply?

    Part Number: LMG1210 [FAQ] Can I use LMG1210 with a bipolar supply? There are several considerations when designing for bipolar bus voltage to make sure that the specifications of the LMG1210 driver are not exceeded at any moment. In general, the…

  • [FAQ] Can TI's non-isolated half bridge drivers be used in 100% duty cycle applications?

    [FAQ] Can TI's non-isolated half bridge drivers be used in 100% duty cycle applications? TI’s non-isolated half bridge drivers do not internally generate the bias for the high side channel. Instead, they use an external bootstrap circuit to keep the…

  • [FAQ] BQ24800: [FAQ] How do I ensure the charger schematic is satisfactory? Is there a schematic checklist for bq24800?

    Part Number: BQ24800 Dear all, The following document shows key considerations when choosing external components for BQ24800. If there are any discrepancies, the datasheet should be referred. Regards, Pengzhao Zhu Application Engineer Texas Ins…

  • [FAQ] BQ24780S: [FAQ] How do I ensure the charger schematic is satisfactory? Is there a schematic checklist for bq24780S?

    Other Parts Discussed in Thread: BQ24780S Dear all, The following document shows key considerations when choosing external components for BQ24780S. If there are any discrepancies, the datasheet should be referred. Regards, Pengzhao Zhu Application…

  • [FAQ] TL431: Is there a simple nomenclature guide for TI's shunt reference families?

    Part Number: TL431 Other Parts Discussed in Thread: TLVH431 , , Do you have a simple device nomenclature guide for shunt references such as (A)TL431, (A)TL431LI, TLVH431 and others?

  • [FAQ] UCC21520: Can a single PWM signal drive a dual input driver?

    Part Number: UCC21520 Other Parts Discussed in Thread: UCC20520 Can a single PWM signal drive a dual input driver?

View FAQ threads