Please provide a list of FAQ for AM62x & Am62Ax Family of Devices
This thread has been locked.
If you have a related question, please click the "Ask a related question" button in the top right corner. The newly created question will be automatically linked to this question.
Please Find the list of FAQ's Below
|[FAQ] SK-AM62: How to flash eMMC using USB DFU on AM62x-SK E2
This thread discusses the process of full Linux eMMC flashing using USB DFU on an AM62x-SK E2 board. A Linux host PC with the tool dfu-util is required.
|[FAQ] AM625 Custom board hardware design – Collaterals to Get started
|a List of collaterals that can be referred when starting a custom board hardware design
|[FAQ] AM625: How to boot from R5 U-Boot SPL directly into the Linux Kernel, skipping A53 SPL and A53 U-Boot (Falcon Mode)
|also applicable to other AM62x, AM62Ax, AM64x, AM65x parts with minor changes
|[FAQ] AM6x: Using multilib to allow running 32-bit binaries on Yocto Dunfell-based v8.x SDKs for Sitara 64-bit MPUs
|This E2E FAQ outlines a way adding multilib support to Yocto Dunfell-based v8.x SDK for AM6x SoCs, and shows an example of a 32-bit AM335x application running on an 64-bit AM62x device
|[FAQ] AM6x/AM335x/AM437x: Using a Yocto-internal toolchain for target image builds and cross-development SDK installer generation with Yocto Dunfell-based v8.x SDKs for Sitara MPUs
|This E2E FAQ shows an alternative approach of how to use an Yocto-internal toolchain for image builds as well as for the associated SDK installer generation that contains the cross-toolchain and the image-specific target sysroot (libraries, header files, etc.) for development of applications that run on Sitara AM6x, AM335x, and AM437x target systems
|[FAQ] AM625: How to measure interrupt latency on multicore Sitara devices using cyclictest?
How can I measure interrupt latency on Sitara multicore devices such as AM625 and compare the results to single core devices such as AM3357?
|[FAQ] AM625: Generating Sitara AM62x/AM62Ax/AM64x GP Device bootable MMC/SD Card Images using SDK v8.6 and Yocto
|This E2E FAQ here outlines an alternative approach of updating the associated Yocto recipes to make the default image bootable on GP devices on the example of an AM62x device, but equally applies to similar scenarios involving devices like AM62Ax and AM64x after reworking the provided patch accordingly. This approach has the advantage of allowing any existing boards such as earlier versions of the AM62-SK development board that was shipped with a GP device to directly boot from MMC/SD card right out of the box without any manual modifications to the filesystem needed
|[FAQ] AM623 Custom board hardware design – Collaterals to Get started
|List of collaterals that can be referred when starting a custom board hardware design
|[FAQ] AM62x & AM64x: How to use CCS to debug a running M4F core that was started by Linux?
|I want to use Code Composer Studio (CCS) to debug a program running on the M4F. The M4F was already initialized and loaded by Linux. I want CCS to attach to the M4F and start debugging the code that is already running (i.e., I do NOT want CCS to restart the M4F or load new code onto the M4F).
|[FAQ] AM335x/AM437x/AM6x: Can I use Processor SDK Linux v8.x with Ubuntu 20.04 or Ubuntu 22.04?
|Ubuntu 18.04 support will be terminated in 2023.
What will be future Ubuntu version plan and schedule
|[FAQ] SK-AM62: How to execute code from external memory using M4F Core?
|How to execute code from external memory using M4F Core?
|[FAQ] SK-AM62: FAQ: How do I set the DIP switches to get a certain boot mode?
|The AM62x SK-EVM has two 8-position DIP switches to set the SoC boot mode and related parameters. How do these switches correspond to the boot mode pins documented in the TRM?
|[FAQ] AM62A7 and AM62A7-Q1 Custom board hardware design – Collaterals to Get started
|List of collaterals that can be referred when starting a custom board hardware design.
|[FAQ] Edge Impulse Setup on TI Processors (ARM-only)
|Edge Impulse is a tool for creating, analyzing, and deploying machine learning to embedded targets
This page will describe how to set up Edge Impulse's Linux command line tools on one of our processor Starter Kits running Linux so it can be connected to Edge Impulse cloud tools.
|[FAQ] AM625: Linux SDK v08.06: U-Boot: USB DFU boot is broken with "dfu_alt_info_ram env variable not defined!" Error
|When trying to boot an AM62x device using the USB DFU boot mode using the U-Boot that is part of the TI Processor SDK Linux v08.06 (www.ti.com/.../08.06.00.42) the error message is output after the initial boot stage (R5 U-Boot SPL) was loaded over USB DFU and started by the ROM code:
|[FAQ] SK-AM62 : How to configure the GPIO interrupt on AM62X in MCU+SDK.
|This FAQ Describes how to Configure Interrupt Router for complex Interrupt routing
|[FAQ] AM625: How to enable DM firmware logs & TIFS firmware logs in Processor SDK Linux v8.4
|How to enable DM firmware logs & TIFS firmware logs in Processor SDK Linux v8.4
|[FAQ] A53 boot binary (tispl.bin) loading error when BOOTMODE="0" in eMMC boot mode on AM62A
|A53 boot binary (tispl.bin) loading error when BOOTMODE="0" in eMMC boot mode on AM62A
|[FAQ] SK-AM62: how to disable the HMI demo
|how reduce boot time, and get command prompt as fast as Possible. Just to have an idea of how to speed up this,how to avoid loading of hmi demo that is automatically loaded at startup
|[FAQ] AM62A7: Import SDK Examples: Solving the AM62Ax Recognition Issue in CCS
|While trying to import SDK example into CCS 12.1.0, some might encounter the problem stating "AM62Ax device not recognized". This FAQ Addresses the issue
|[FAQ] AM62x: How to customize eMMC and OSPI flash layout for SPL/u-boot booting with TI AM62x Linux SDK
|How to customize eMMC and OSPI flash layout for SPL/u-boot booting with TI AM62x Linux SDK
|[FAQ] AM62x: U-Boot Build on SDK v8.06 fails with 'make: arm-linux-androideabi-ld.gold: No such file or directory' error
|When building U-Boot for A53 on AM62x using SDK v8.06, the build may break
|[FAQ] AM625: Is Flutter the right GUI toolkit for me: an engineers perspective.
|Is Flutter the right GUI toolkit for me: an engineers perspective
|[FAQ] SK-AM62: Steps to enable Expansion Header I2C and power
|Steps to enable Expansion Header I2C and power
|[FAQ] AM62A7 or AM62A3 Custom board hardware design - Reusing TI EVM design files
|I am starting a new board design and planning to use TI EVM design files for designing my custom board.
Please let me know if you have any suggestions.
|[FAQ] AM62A3 and AM62A3-Q1 Custom board hardware design – Collaterals to Get started
|Can you provide a List of collaterals that can be referred when starting a custom board hardware design.
|[FAQ] PROCESSOR-SDK-AM62X: Run MCU-PLUS-SDK Examples From R5_0_0 Core Using SBL NULL
|After reading this FAQ:
You will be able to run the MCU PLUS SDK R5_0_0 examples via SBL Null.
You will be able to see the output of the SDK examples on the WAKEUP Terminal.
|[FAQ] PROCESSOR-SDK-AM62X: How to read device Id register
|device Id register address is not defined in AM62x TRM.
What is the base address to read device id register ?
an we read via omapconf or devmem utils ?