Because of the Thanksgiving holiday in the U.S., TI E2E™ design support forum responses may be delayed from November 25 through December 2. Thank you for your patience.

Texas Instruments (TI) Processors support forum is an extensive online knowledge base where millions of technical questions and solutions are available 24/7. You can search processors content or ask technical support questions on Sitara™ processors, digital signal processors (DSP) and automotive processors. Find the right solution for your circuit design challenges by using our TI E2E™ support forums that are supported by thousands of contributing TI experts.
Frequent questions

  • [FAQ] SK-AM69: How to stream from CSI sensor to display using GStreamer?

    Part Number: SK-AM69 Other Parts Discussed in Thread: SK-AM68 , AM67 , SK-TDA4VM Tool/software: Hi, I have a Starter Kit (SK) Edge AI device with a CSI sensor connected and would like to stream to my display. I have enabled the sensor by following the…

  • [FAQ] : How to test ECC for R5F Cache Memories on AM6x/AM243 devices.

    Part Number: SK-AM62B-P1 Tool/software: Is ECC (SEC/DED) testing possible on R5F internal cache memories? If yes, please provide the steps to do so.

  • [FAQ] AM625: Package parameter description

    Part Number: AM625 Other Parts Discussed in Thread: AM623 Tool/software: Hi TI, I`d like to know the meaning of below parameter. 0.35, 0.25, 0.15, 0.08. What is the meaning of these 4 parameter? BR Cayden

  • [FAQ] AM2432: Please give some information of Schematic design for FSI?

    Part Number: AM2432 Other Parts Discussed in Thread: AM6412 , AM6422 , AM6442 , AM2434 Tool/software: Hi At the document SPRACU5C "AM6442, AM6422, AM6412 and AM2434 Schematic Design and Review Checklist" ( link ), there is no description for FSI…

  • [FAQ] AM62A3-Q1: AM62A3-Q1 PDN Power SI SIMULATION Questions

    Part Number: AM62A3-Q1 Tool/software: Hello，I have some doubts about PDN simulation (Power SI), please help to solve it 1、Do I need to separate VDD_CORE-1 to 17 for simulation, or use VDD_CORE as a Port? 2、Do I need to include the PMIC FB loop in the…

  • [FAQ] How to Setup IBV icECAT EtherCAT Master Stack on TI Processors?

    Part Number: AM6442 Other Parts Discussed in Thread: LP-AM243 , TMDS64EVM Tool/software: icECAT is a 3rd party EtherCAT Master stack developed by IBV . To obtain the software stack for evaluation please send a request by selecting the "Send Request" button…

  • [FAQ] How to Setup an EtherCAT Network using TI Processors

    Part Number: AM6442 Tool/software: TI processors have the capability to run as an EtherCAT MainDevice to control EtherCAT SubDevices such Beckhoff I/O terminals or an AM243x running an EtherCAT subdevice example . This is enabled by using a 3rd party EtherCAT…

  • [FAQ] TDA4VH-Q1 and TDA4VL-Q1: Errata i2437 - Streaming Engine (SE) Clock-Gating Turning Off Too Early: Background and Workaround

    Part Number: TDA4VH-Q1 Tool/software: Background Errata ID: i2437 refers to the C7x Streaming Engine (SE). This errata applies to J721S2 and J784S4 and the details can be found in their respective Processor Silicon Revision documents. Note that this is…

  • [FAQ]:Migration Tips for Developers Transitioning to MPU Devices from Old Microcontroller.

    Part Number: AM6442 Other Parts Discussed in Thread: AM62P Tool/software: With this FAQ, developers can ensure a smoother, faster transition to Sitara MPU devices (AM64x,AM243,AM62x,AM62A,AM62P and AM62D) and maximizing the benefits of the new architecture…

  • [FAQ] AM62A7-Q1: Balena etcher flash error workaround

    Part Number: AM62A7-Q1 Tool/software: Hi all, Due to the latest version(V1.19.x) Balena etcher have some bugs will cause flash error report. regarding this error, pls use old version Balena tool to work around. below is the download link for V1.7.x,…

View FAQ threads
  • Threads 188768 Discussions