回复：Sensors forum: XDS 110

user6315392

Other Parts Discussed in Thread: AWR1642, AWR1843, AWR1642BOOST, UNIFLASH

Dear Cesar

Thank you very much for your reply,

1. I'm sorry I wrote the wrong radar model. I used AWR1843. I have consulted about the two radars AWR1642 and AWR1843 before. AWR1843 can use the code of the toolkit mmwave_automotive_toolbox_3_0_0.I asked your questions when using lab0002.

2. I am using SDK demo.

Looking forward to your positive reply.

Thank you very much.

------------------ 原始邮件 ------------------

发件人: "mmwave_sensors_forum" <bounce-20288@mail.e2e.ti.com>;

发送时间: 2020年8月30日(星期天) 凌晨0:26

收件人: "mmwave_sensors_forum"<mmwave_sensors_forum@mail.e2e.ti.com>;

主题: Sensors forum: XDS 110

A Message from the TI E2E™ support forums

Cesar replied to XDS 110.

Please let us know

1) are you using AWR1642Boost EVM?

2) are you using the mmwave SDK demo?

Thank you

Cesar

----------------------------------------------------------------------------------------------------------

Please check TI mmWave FAQs before posting a new query
----------------------------------------------------------------------------------------------------------

You received this notification because you subscribed to the forum. To unsubscribe from only this thread, go here.

Flag this post as spam/abuse.

refid:f108f374-8f5e-4f10-8fcd-071368f1d7e3

over 5 years ago

0 Jitendra Gupta over 5 years ago

TI__Guru 69960 points

Based on your original thread-

https://e2e.ti.com/support/sensors/f/1023/t/935970

SRR demo from TI-Rex uses PC based GUI application to connect with mmwave sensor. Please note that SRR application is built for AWR1642 device.

And MRR demo is built for AWR1843 device.

Now, if you are trying to flash the binary using Uniflash tool then after flashing done close the tool and change the SOP setting to functional mode.

try to do board power cycle and re-connect USB cable. Now try to execute the GUI for SRR/MRR demo.

Regards,

Jitendra

0 user6315392 over 5 years ago

Prodigy 30 points

Dear Jitendra Gupta ：

Thank you very much for your reply.

Regarding the SOP setting that you mentioned, when I run lab0002 in the toolkit mmwave_automotive_toolbox_3_0_0 on AWR1843, what is the SOP value when I burn the BIN file? Is it 1 0 1 or what value? When running GUI, what is the value of AWR1843 SOP function mode setting? I did not find information about the setting of the SOP value when running the GUI in the AWR1843 document.

Looking forward to your positive reply.

Thank you very much.

------------------ 原始邮件 ------------------

发件人: "mmwave_sensors_forum" <bounce-1717369@mail.e2e.ti.com>;

发送时间: 2020年8月31日(星期一) 晚上6:13

收件人: "mmwave_sensors_forum"<mmwave_sensors_forum@mail.e2e.ti.com>;

主题: Sensors forum: 回复：Sensors forum: XDS 110

A Message from the TI E2E™ support forums

Jitendra Gupta replied to 回复：Sensors forum: XDS 110.

Based on your original thread-

https://e2e.ti.com/support/sensors/f/1023/t/935970

SRR demo from TI-Rex uses PC based GUI application to connect with mmwave sensor. Please note that SRR application is built for AWR1642 device.

And MRR demo is built for AWR1843 device.

Now, if you are trying to flash the binary using Uniflash tool then after flashing done close the tool and change the SOP setting to functional mode.

try to do board power cycle and re-connect USB cable. Now try to execute the GUI for SRR/MRR demo.

Regards,

Jitendra

----------------------------------------------------------------------------------------------------------

Please check TI mmWave FAQs before posting a new query
----------------------------------------------------------------------------------------------------------

You received this notification because you subscribed to the forum. To unsubscribe from only this thread, go here.

Flag this post as spam/abuse.

refid:97ace27c-973d-4a12-9f9c-b8651a6ea9e9

0 Jitendra Gupta over 5 years ago in reply to user6315392

TI__Guru 69960 points

Hello,

For flashing SOP settings (SOP-0:1, SOP1- 0, SOP-2: 1)

Functional Mode: (SOP-0:1, SOP1- 0, SOP-2: 0)

These information is available in the user guide.

Regards,

Jitendra