CCS/MSP430G2553: Lipo battery charger

user6069086

Part Number: MSP430G2553
Other Parts Discussed in Thread: MSP430G2533, , MSP430F1122, MSP430F1132, MSP430F1222, MSP430F1232

Tool/software: Code Composer Studio

Hello,

I want to make lipo battery charge circuit with MSP430G2533.

I dont know how make circuit and software with MSP430G2553.

Can anyone help me?

Thanks..

over 4 years ago

0 JD Crutchfield over 4 years ago

TI__Mastermind 26380 points

Hello,

There is an older application note addressing a possible solution: http://www.ti.com/lit/an/slaa287a/slaa287a.pdf

I think that using a TI Charging solution is probably currently the best solution. Something like this: http://www.ti.com/lit/an/slaa529a/slaa529a.pdf

Unfortunately, I'm not aware of any software to go along with either solution. That would have to be developed.

Thanks,

0 user6069086 over 4 years ago in reply to JD Crutchfield

Prodigy 20 points

Thanks for the answer.

I studied these documents but unfortunately it did not work for me.

I search for msp430g2553. Does anyone else have a solution for msp430g2553?

0 JD Crutchfield over 4 years ago in reply to user6069086

TI__Mastermind 26380 points

Hello,

I'm not familiar with your system, but I would like to point you to TI's Battery Management solutions: http://www.ti.com/power-management/battery-management/overview.html

Hopefully, you can find information there on a solution that will work for you!

Thanks,

0 Tomasz Kocon over 4 years ago in reply to user6069086

Guru 26200 points

Find below a brief characteristic of the MSP430F12x2 family.
Compare it with MSP430G2553.
It should not be a big deal to port F12x2 code to your platform.

Supply Voltage Range 1.8 V to 3.6
Ultralow-Power Consumption: − Active Mode: 200 µA at 1 MHz, 2.2 V − Standby Mode: 0.7 µA − Off Mode (RAM Retention): 0.1 µA
Power Saving Modes
Wake-Up From Standby Mode in less than 6 µs
16-Bit RISC Architecture, 125 ns Instruction Cycle Time
Clock Module Configurations: − Various Internal Resistors − Single External Resistor − 32-kHz Crystal − High Frequency Crystal − Resonator − External Clock Source
16-Bit Timer_A With Three Capture/Compare Registers
10-Bit, 200-ksps A/D Converter With Internal Reference, Sample-and-Hold, Autoscan, and Data Transfer Controller
Communication Interface (USART0) With Software-Selectable Asynchronous UART or Synchronous SPI (MSP430x12x2 Only)
Onboard Programming, No External Programming Voltage Needed Programmable Code Protection by Security Fuse
Voltage Brownout Protection
Family Members Include:
MSP430F1122: 4KB + 256B Flash Memory 256B RAM
MSP430F1132: 8KB + 256B Flash Memory 256B RAM
Available in 20-Pin Plastic SOWB, 20-Pin Plastic TSSOP and 32-Pin QFN Packages
Family Members Include:
MSP430F1222: 4KB + 256B Flash Memory 256B RAM
MSP430F1232: 8KB + 256B Flash Memory 256B RAM
Available in 28-Pin Plastic SOWB, 28-Pin Plastic TSSOP, and 32-Pin QFN Packages
Complete Module Descriptions, See the MSP430x1xx Family User’s Guide, Literature Number SLAU049

0 JD Crutchfield over 4 years ago in reply to Tomasz Kocon

TI__Mastermind 26380 points

Hey Tomasz,

I'm not sure you responded to the correct thread here.

Thanks,

0 Tomasz Kocon over 4 years ago in reply to JD Crutchfield

Guru 26200 points

Hey JD,

your link http://www.ti.com/lit/an/slaa287a/slaa287a.pdf
refers to the simple solution based on the MSP430F12x2 family
and the link to a source code is there.

That is why I wrote: It should not be a big deal to port F12x2 code to your platform.

Code Composer Studio™︎

Code Composer Studio forum

CCS/MSP430G2553: Lipo battery charger