CC2564: HCI commands inquiry and write scan enable - behaviour

Dietmar Sierk

Part Number: CC2564
Other Parts Discussed in Thread: CC256XB-BT-SP,

Hi,

due to obsolescence topics, we try to replace a HCI-module with a blucore 4 (CSR) chipset by a TI CC2564 HCI module.

To compare and verify our used HCI commands (there are no vendor specific commands used) I have used your evaluation board and the TI-HCI test suite.

In general it looks fine, ACL data connection works.

But I see two differences, where I need some help:

The HCI inquiry command works fine direct after bootup of the module. E.g. after changing the scan enable parameter (HCI wirte scan enable command), the module will not give any inquiry result any more. To clear the scan enable, does not bring the inquiry function back to work. So far, I have only found the power cycle to bring it back to work.

It seems to be not possible to attach log files (html)?

2. In general the write scan enable for page or inquiry does not work. The HCI command will be responded by a succeeded command complete, but the device is not visible to other bluetoot devices.

May be the ti chipset does need a other initialization than a bluecore 4 chipset (for that, currently after power ups, there are no additional init steps needed). Could you help us directly or can you reference some documents to find to answers for this behavior?

Thanks

Dietmar

Fullscreen HCITester Trace Log_after write scan enable not ok.htm Download

<HTML>
<HEAD>
<TITLE>HCITester Log</TITLE>
</HEAD>
<BODY>
<FONT face="Courier New">
<TABLE ALIGN=LEFT CELLSPACING=0 width=3500 CELLPADDING=0>
<tr bgcolor="ffffe6"><td><font color="0000c0">10:32:03.175 --</font></td></tr>
<tr bgcolor="ffffe6"><td><font color="0000c0">10:32:03.175 Packet "HCI_Read_Scan_Enable", Opcode 0x0c19</font></td></tr>
<tr bgcolor="ffffe6"><td><font color="0000c0">10:32:03.175 --</font></td></tr>
<tr bgcolor="60c0c0"><td><font color="ffffff">10:32:03.175 Outgoing Dump:</font></td></tr>
<tr bgcolor="60c0c0"><td><font color="ffffff">10:32:03.175     0000: 01 19 0c 00                                     ....</font></td></tr>
<tr bgcolor="408080"><td><font color="ffffff">10:32:03.179 Incoming Dump:</font></td></tr>
<tr bgcolor="408080"><td><font color="ffffff">10:32:03.179     0000: 04 0e 05 01 19 0c 00 00                         ........</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:32:03.179 --</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:32:03.179 Packet "HCI_Command_Complete_Read_Scan_Enable_Event", Opcode 0x0c19</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:32:03.179 Parameters:</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:32:03.179 | Number HCI commands : 0x01</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:32:03.179 | Command Opcode      : 0x0c19</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:32:03.179 | Status              : 0x00 (Success)</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:32:03.179 | Scan Enable         : 0x00 (No Scans)</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:32:03.179 --</font></td></tr>
<tr bgcolor="ffffe6"><td><font color="0000c0">10:32:12.448 --</font></td></tr>
<tr bgcolor="ffffe6"><td><font color="0000c0">10:32:12.448 Packet "HCI_Inquiry", Opcode 0x0401</font></td></tr>
<tr bgcolor="ffffe6"><td><font color="0000c0">10:32:12.448 Parameters:</font></td></tr>
<tr bgcolor="ffffe6"><td><font color="0000c0">10:32:12.448 | LAP                 : "9E8B33"</font></td></tr>
<tr bgcolor="ffffe6"><td><font color="0000c0">10:32:12.448 | Inquiry Length      : 0x08</font></td></tr>
<tr bgcolor="ffffe6"><td><font color="0000c0">10:32:12.448 | Number of Responses : 0x00</font></td></tr>
<tr bgcolor="ffffe6"><td><font color="0000c0">10:32:12.448 --</font></td></tr>
<tr bgcolor="60c0c0"><td><font color="ffffff">10:32:12.448 Outgoing Dump:</font></td></tr>
<tr bgcolor="60c0c0"><td><font color="ffffff">10:32:12.448     0000: 01 01 04 05 33 8b 9e 08 00                      ....3....</font></td></tr>
<tr bgcolor="408080"><td><font color="ffffff">10:32:12.463 Incoming Dump:</font></td></tr>
<tr bgcolor="408080"><td><font color="ffffff">10:32:12.463     0000: 04 0f 04 00 01 01 04                            .......</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:32:12.463 --</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:32:12.463 Packet "HCI_Command_Status_Event", Opcode 0x000f</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:32:12.463 Parameters:</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:32:12.463 | Status              : 0x00 (Success)</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:32:12.463 | Number HCI commands : 0x01</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:32:12.463 | Command Opcode      : 0x0401</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:32:12.463 --</font></td></tr>
<tr bgcolor="408080"><td><font color="ffffff">10:32:12.766 Incoming Dump:</font></td></tr>
<tr bgcolor="408080"><td><font color="ffffff">10:32:12.766     0000: 04 02 0f 01 27 0e dd 18 b3 e4 01 02 00 0c 01 7c ....'..........|</font></td></tr>
<tr bgcolor="408080"><td><font color="ffffff">10:32:12.766     0010: 1c 3d                                           .=</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:32:12.766 --</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:32:12.766 Packet "HCI_Inquiry_Result_Event", Opcode 0x0002</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:32:12.766 Parameters:</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:32:12.766 | Number of Responses       : 0x01</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:32:12.766 | BD_ADDR responded         : "E4:B3:18:DD:0E:27"</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:32:12.766 | Page Scan Repetition Mode : 0x01 (R1)</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:32:12.766 | Page Scan Period Mode     : 0x02 (P2)</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:32:12.766 | Page Scan Mode            : 0x00 (Mandatory)</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:32:12.766 | Class of Device           : 0x7c010c</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:32:12.766 | Clock Offset              : 0x3d1c</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:32:12.766 --</font></td></tr>
<tr bgcolor="408080"><td><font color="ffffff">10:32:15.354 Incoming Dump:</font></td></tr>
<tr bgcolor="408080"><td><font color="ffffff">10:32:15.354     0000: 04 02 0f 01 8e ca 14 96 a0 00 01 00 00 00 00 00 ................</font></td></tr>
<tr bgcolor="408080"><td><font color="ffffff">10:32:15.354     0010: 6c 6d                                           lm</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:32:15.355 --</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:32:15.355 Packet "HCI_Inquiry_Result_Event", Opcode 0x0002</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:32:15.355 Parameters:</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:32:15.355 | Number of Responses       : 0x01</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:32:15.355 | BD_ADDR responded         : "00:A0:96:14:CA:8E"</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:32:15.355 | Page Scan Repetition Mode : 0x01 (R1)</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:32:15.355 | Page Scan Period Mode     : 0x00 (P0)</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:32:15.355 | Page Scan Mode            : 0x00 (Mandatory)</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:32:15.355 | Class of Device           : 0x000000</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:32:15.355 | Clock Offset              : 0x6d6c</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:32:15.355 --</font></td></tr>
<tr bgcolor="408080"><td><font color="ffffff">10:32:16.473 Incoming Dump:</font></td></tr>
<tr bgcolor="408080"><td><font color="ffffff">10:32:16.473     0000: 04 02 0f 01 8c a6 be 99 66 c4 01 02 00 0c 02 5a ........f......Z</font></td></tr>
<tr bgcolor="408080"><td><font color="ffffff">10:32:16.473     0010: 16 11                                           ..</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:32:16.473 --</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:32:16.473 Packet "HCI_Inquiry_Result_Event", Opcode 0x0002</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:32:16.473 Parameters:</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:32:16.473 | Number of Responses       : 0x01</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:32:16.473 | BD_ADDR responded         : "C4:66:99:BE:A6:8C"</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:32:16.473 | Page Scan Repetition Mode : 0x01 (R1)</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:32:16.473 | Page Scan Period Mode     : 0x02 (P2)</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:32:16.473 | Page Scan Mode            : 0x00 (Mandatory)</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:32:16.473 | Class of Device           : 0x5a020c</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:32:16.473 | Clock Offset              : 0x1116</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:32:16.473 --</font></td></tr>
<tr bgcolor="408080"><td><font color="ffffff">10:32:22.704 Incoming Dump:</font></td></tr>
<tr bgcolor="408080"><td><font color="ffffff">10:32:22.704     0000: 04 01 01 00                                     ....</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:32:22.704 --</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:32:22.704 Packet "HCI_Inquiry_Complete_Event", Opcode 0x0001</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:32:22.704 Parameters:</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:32:22.704 | Status : 0x00 (Success)</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:32:22.704 --</font></td></tr>
<tr bgcolor="ffffff"><td><font color="000000">10:33:14.525 *** Script Started: "D:\Installation\TI\Script _init_.txt" ***</font></td></tr>
<tr bgcolor="ffffe6"><td><font color="0000c0">10:33:14.525 --</font></td></tr>
<tr bgcolor="ffffe6"><td><font color="0000c0">10:33:14.525 Packet "HCI_Change_Local_Name", Opcode 0x0c13</font></td></tr>
<tr bgcolor="ffffe6"><td><font color="0000c0">10:33:14.525 Parameters:</font></td></tr>
<tr bgcolor="ffffe6"><td><font color="0000c0">10:33:14.525 | New name : "Bluetooth By Texas Instruments"</font></td></tr>
<tr bgcolor="ffffe6"><td><font color="0000c0">10:33:14.525 --</font></td></tr>
<tr bgcolor="60c0c0"><td><font color="ffffff">10:33:14.525 Outgoing Dump:</font></td></tr>
<tr bgcolor="60c0c0"><td><font color="ffffff">10:33:14.525     0000: 01 13 0c f8 42 6c 75 65 74 6f 6f 74 68 20 42 79 ....Bluetooth By</font></td></tr>
<tr bgcolor="60c0c0"><td><font color="ffffff">10:33:14.525     0010: 20 54 65 78 61 73 20 49 6e 73 74 72 75 6d 65 6e  Texas Instrumen</font></td></tr>
<tr bgcolor="60c0c0"><td><font color="ffffff">10:33:14.525     0020: 74 73 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ts..............</font></td></tr>
<tr bgcolor="60c0c0"><td><font color="ffffff">10:33:14.525     0030: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................</font></td></tr>
<tr bgcolor="60c0c0"><td><font color="ffffff">10:33:14.525     0040: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................</font></td></tr>
<tr bgcolor="60c0c0"><td><font color="ffffff">10:33:14.525     0050: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................</font></td></tr>
<tr bgcolor="60c0c0"><td><font color="ffffff">10:33:14.525     0060: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................</font></td></tr>
<tr bgcolor="60c0c0"><td><font color="ffffff">10:33:14.525     0070: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................</font></td></tr>
<tr bgcolor="60c0c0"><td><font color="ffffff">10:33:14.525     0080: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................</font></td></tr>
<tr bgcolor="60c0c0"><td><font color="ffffff">10:33:14.525     0090: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................</font></td></tr>
<tr bgcolor="60c0c0"><td><font color="ffffff">10:33:14.525     00a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................</font></td></tr>
<tr bgcolor="60c0c0"><td><font color="ffffff">10:33:14.525     00b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................</font></td></tr>
<tr bgcolor="60c0c0"><td><font color="ffffff">10:33:14.525     00c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................</font></td></tr>
<tr bgcolor="60c0c0"><td><font color="ffffff">10:33:14.525     00d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................</font></td></tr>
<tr bgcolor="60c0c0"><td><font color="ffffff">10:33:14.525     00e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................</font></td></tr>
<tr bgcolor="60c0c0"><td><font color="ffffff">10:33:14.525     00f0: 00 00 00 00 00 00 00 00 00 00 00 00             ............</font></td></tr>
<tr bgcolor="408080"><td><font color="ffffff">10:33:14.552 Incoming Dump:</font></td></tr>
<tr bgcolor="408080"><td><font color="ffffff">10:33:14.552     0000: 04 0e 04 01 13 0c 00                            .......</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:33:14.552 --</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:33:14.552 Packet "HCI_Command_Complete_Change_Local_Name_Event", Opcode 0x0c13</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:33:14.552 Parameters:</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:33:14.552 | Number HCI commands : 0x01</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:33:14.552 | Command Opcode      : 0x0c13</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:33:14.552 | Status              : 0x00 (Success)</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:33:14.552 --</font></td></tr>
<tr bgcolor="ffffe6"><td><font color="0000c0">10:33:14.552 --</font></td></tr>
<tr bgcolor="ffffe6"><td><font color="0000c0">10:33:14.552 Packet "HCI_Read_Local_Name", Opcode 0x0c14</font></td></tr>
<tr bgcolor="ffffe6"><td><font color="0000c0">10:33:14.552 --</font></td></tr>
<tr bgcolor="60c0c0"><td><font color="ffffff">10:33:14.552 Outgoing Dump:</font></td></tr>
<tr bgcolor="60c0c0"><td><font color="ffffff">10:33:14.552     0000: 01 14 0c 00                                     ....</font></td></tr>
<tr bgcolor="408080"><td><font color="ffffff">10:33:14.591 Incoming Dump:</font></td></tr>
<tr bgcolor="408080"><td><font color="ffffff">10:33:14.591     0000: 04 0e fc 01 14 0c 00 42 6c 75 65 74 6f 6f 74 68 .......Bluetooth</font></td></tr>
<tr bgcolor="408080"><td><font color="ffffff">10:33:14.591     0010: 20 42 79 20 54 65 78 61 73 20 49 6e 73 74 72 75  By Texas Instru</font></td></tr>
<tr bgcolor="408080"><td><font color="ffffff">10:33:14.591     0020: 6d 65 6e 74 73 00 d0 1f a7 ed e7 da 3a c5 5e e6 ments.......:.^.</font></td></tr>
<tr bgcolor="408080"><td><font color="ffffff">10:33:14.591     0030: 1d 0f ad 29 d5 da 88 49 6c 27 89 ef bb 2f b3 ab ...)...Il'.../..</font></td></tr>
<tr bgcolor="408080"><td><font color="ffffff">10:33:14.591     0040: 11 da 6e b0 a1 e8 be cc 18 90 ca 59 37 df 9e 8f ..n........Y7...</font></td></tr>
<tr bgcolor="408080"><td><font color="ffffff">10:33:14.591     0050: f2 a9 e6 6c 4b 87 86 23 b2 c4 f9 51 b9 fe dc ef ...lK..#...Q....</font></td></tr>
<tr bgcolor="408080"><td><font color="ffffff">10:33:14.591     0060: e7 e1 f0 40 a7 fc 89 79 ea 0b 66 da 70 fd 9a 45 ...@...y..f.p..E</font></td></tr>
<tr bgcolor="408080"><td><font color="ffffff">10:33:14.591     0070: f3 37 7d d3 95 7a 7b 27 d7 82 ed 5c 49 dd e5 b3 .7}..z{'...\I...</font></td></tr>
<tr bgcolor="408080"><td><font color="ffffff">10:33:14.591     0080: 59 5d 24 f8 1e bb 3f d5 91 ff 77 81 f2 c6 7e 7d Y]$...?...w...~}</font></td></tr>
<tr bgcolor="408080"><td><font color="ffffff">10:33:14.591     0090: 17 de 1e 1c 78 6a 9d 17 95 f0 6c c9 d9 88 26 0b ....xj....l...&amp;.</font></td></tr>
<tr bgcolor="408080"><td><font color="ffffff">10:33:14.591     00a0: 8e e5 c7 91 32 75 21 58 42 96 1f db f2 87 1b f3 ....2u!XB.......</font></td></tr>
<tr bgcolor="408080"><td><font color="ffffff">10:33:14.591     00b0: c7 1f 71 38 74 7f 78 ef ad a7 d6 1b 0c f9 ab 34 ..q8t.x........4</font></td></tr>
<tr bgcolor="408080"><td><font color="ffffff">10:33:14.591     00c0: a8 b3 18 41 8b 7b 5b a9 0e 41 ee 9c cf 09 d6 ff ...A.{[..A......</font></td></tr>
<tr bgcolor="408080"><td><font color="ffffff">10:33:14.591     00d0: b9 f8 c5 f9 d7 03 51 b2 7e 53 b2 46 8b b0 df 60 ......Q.~S.F...`</font></td></tr>
<tr bgcolor="408080"><td><font color="ffffff">10:33:14.591     00e0: 8d 4a 33 b3 fd de fb 84 d9 a9 51 61 c6 7d 9c e3 .J3.......Qa.}..</font></td></tr>
<tr bgcolor="408080"><td><font color="ffffff">10:33:14.591     00f0: 69 60 f8 2b 17 ce 0d c0 81 f3 ba 09 15 87 73    i`.+..........s</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:33:14.591 --</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:33:14.591 Packet "HCI_Command_Complete_Read_Local_Name_Event", Opcode 0x0c14</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:33:14.591 Parameters:</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:33:14.591 | Number HCI commands : 0x01</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:33:14.591 | Command Opcode      : 0x0c14</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:33:14.591 | Status              : 0x00 (Success)</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:33:14.591 | Local Name          : "Bluetooth By Texas Instruments"</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:33:14.591 --</font></td></tr>
<tr bgcolor="ffffe6"><td><font color="0000c0">10:33:14.591 --</font></td></tr>
<tr bgcolor="ffffe6"><td><font color="0000c0">10:33:14.591 Packet "HCI_Write_Scan_Enable", Opcode 0x0c1a</font></td></tr>
<tr bgcolor="ffffe6"><td><font color="0000c0">10:33:14.591 Parameters:</font></td></tr>
<tr bgcolor="ffffe6"><td><font color="0000c0">10:33:14.591 | Scan Enable : 0x03 (Page and Inquiry Scan)</font></td></tr>
<tr bgcolor="ffffe6"><td><font color="0000c0">10:33:14.591 --</font></td></tr>
<tr bgcolor="60c0c0"><td><font color="ffffff">10:33:14.591 Outgoing Dump:</font></td></tr>
<tr bgcolor="60c0c0"><td><font color="ffffff">10:33:14.591     0000: 01 1a 0c 01 03                                  .....</font></td></tr>
<tr bgcolor="408080"><td><font color="ffffff">10:33:14.607 Incoming Dump:</font></td></tr>
<tr bgcolor="408080"><td><font color="ffffff">10:33:14.607     0000: 04 0e 04 01 1a 0c 00                            .......</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:33:14.607 --</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:33:14.607 Packet "HCI_Command_Complete_Write_Scan_Enable_Event", Opcode 0x0c1a</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:33:14.607 Parameters:</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:33:14.607 | Number HCI commands : 0x01</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:33:14.607 | Command Opcode      : 0x0c1a</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:33:14.607 | Status              : 0x00 (Success)</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:33:14.607 --</font></td></tr>
<tr bgcolor="ffffe6"><td><font color="0000c0">10:33:14.607 --</font></td></tr>
<tr bgcolor="ffffe6"><td><font color="0000c0">10:33:14.607 Packet "HCI_Read_Scan_Enable", Opcode 0x0c19</font></td></tr>
<tr bgcolor="ffffe6"><td><font color="0000c0">10:33:14.607 --</font></td></tr>
<tr bgcolor="60c0c0"><td><font color="ffffff">10:33:14.607 Outgoing Dump:</font></td></tr>
<tr bgcolor="60c0c0"><td><font color="ffffff">10:33:14.607     0000: 01 19 0c 00                                     ....</font></td></tr>
<tr bgcolor="408080"><td><font color="ffffff">10:33:14.623 Incoming Dump:</font></td></tr>
<tr bgcolor="408080"><td><font color="ffffff">10:33:14.623     0000: 04 0e 05 01 19 0c 00 03                         ........</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:33:14.623 --</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:33:14.623 Packet "HCI_Command_Complete_Read_Scan_Enable_Event", Opcode 0x0c19</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:33:14.623 Parameters:</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:33:14.623 | Number HCI commands : 0x01</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:33:14.623 | Command Opcode      : 0x0c19</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:33:14.623 | Status              : 0x00 (Success)</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:33:14.623 | Scan Enable         : 0x03 (Page and Inquiry Scan)</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:33:14.623 --</font></td></tr>
<tr bgcolor="ffffff"><td><font color="000000">10:33:14.623 --</font></td></tr>
<tr bgcolor="ffffff"><td><font color="000000">10:33:14.623 *** Script End ***</font></td></tr>
<tr bgcolor="ffffff"><td><font color="000000">10:33:14.623 --</font></td></tr>
<tr bgcolor="ffffe6"><td><font color="0000c0">10:33:39.724 --</font></td></tr>
<tr bgcolor="ffffe6"><td><font color="0000c0">10:33:39.724 Packet "HCI_Inquiry", Opcode 0x0401</font></td></tr>
<tr bgcolor="ffffe6"><td><font color="0000c0">10:33:39.724 Parameters:</font></td></tr>
<tr bgcolor="ffffe6"><td><font color="0000c0">10:33:39.724 | LAP                 : "9E8B33"</font></td></tr>
<tr bgcolor="ffffe6"><td><font color="0000c0">10:33:39.724 | Inquiry Length      : 0x08</font></td></tr>
<tr bgcolor="ffffe6"><td><font color="0000c0">10:33:39.724 | Number of Responses : 0x00</font></td></tr>
<tr bgcolor="ffffe6"><td><font color="0000c0">10:33:39.724 --</font></td></tr>
<tr bgcolor="60c0c0"><td><font color="ffffff">10:33:39.724 Outgoing Dump:</font></td></tr>
<tr bgcolor="60c0c0"><td><font color="ffffff">10:33:39.725     0000: 01 01 04 05 33 8b 9e 08 00                      ....3....</font></td></tr>
<tr bgcolor="408080"><td><font color="ffffff">10:33:39.740 Incoming Dump:</font></td></tr>
<tr bgcolor="408080"><td><font color="ffffff">10:33:39.740     0000: 04 0f 04 00 01 01 04                            .......</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:33:39.740 --</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:33:39.740 Packet "HCI_Command_Status_Event", Opcode 0x000f</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:33:39.740 Parameters:</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:33:39.740 | Status              : 0x00 (Success)</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:33:39.740 | Number HCI commands : 0x01</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:33:39.740 | Command Opcode      : 0x0401</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:33:39.740 --</font></td></tr>
<tr bgcolor="408080"><td><font color="ffffff">10:33:49.982 Incoming Dump:</font></td></tr>
<tr bgcolor="408080"><td><font color="ffffff">10:33:49.982     0000: 04 01 01 00                                     ....</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:33:49.982 --</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:33:49.982 Packet "HCI_Inquiry_Complete_Event", Opcode 0x0001</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:33:49.982 Parameters:</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:33:49.982 | Status : 0x00 (Success)</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">10:33:49.982 --</font></td></tr>
</TABLE>
</FONT>
</BODY>
</HTML>

over 7 years ago

0 S over 7 years ago

TI__Mastermind 35795 points

Dietmar,
Can you pls capture and share firmware log
processors.wiki.ti.com/.../CC256x_Logger_User_Guide

Thanks
Saurabh

0 Dietmar Sierk over 7 years ago in reply to S

Prodigy 80 points

There is the log from the TI-HCI test tool,

the beginning is direct after power up and you can see that the inquiry works.

After configuration of local name and scan enable there is a second inquiry command, which does not work.

Please trust me, that the other Bluetooth devices are still present.

Thanks a lot.

Dietmar

10:32:03.175 --

10:32:03.175 Packet "HCI_Read_Scan_Enable", Opcode 0x0c19

10:32:03.175 --

10:32:03.175 Outgoing Dump:

10:32:03.175 0000: 01 19 0c 00 ....

10:32:03.179 Incoming Dump:

10:32:03.179 0000: 04 0e 05 01 19 0c 00 00 ........

10:32:03.179 --

10:32:03.179 Packet "HCI_Command_Complete_Read_Scan_Enable_Event", Opcode 0x0c19

10:32:03.179 Parameters:

10:32:03.179 | Number HCI commands : 0x01

10:32:03.179 | Command Opcode : 0x0c19

10:32:03.179 | Status : 0x00 (Success)

10:32:03.179 | Scan Enable : 0x00 (No Scans)

10:32:03.179 --

10:32:12.448 --

10:32:12.448 Packet "HCI_Inquiry", Opcode 0x0401

10:32:12.448 Parameters:

10:32:12.448 | LAP : "9E8B33"

10:32:12.448 | Inquiry Length : 0x08

10:32:12.448 | Number of Responses : 0x00

10:32:12.448 --

10:32:12.448 Outgoing Dump:

10:32:12.448 0000: 01 01 04 05 33 8b 9e 08 00 ....3....

10:32:12.463 Incoming Dump:

10:32:12.463 0000: 04 0f 04 00 01 01 04 .......

10:32:12.463 --

10:32:12.463 Packet "HCI_Command_Status_Event", Opcode 0x000f

10:32:12.463 Parameters:

10:32:12.463 | Status : 0x00 (Success)

10:32:12.463 | Number HCI commands : 0x01

10:32:12.463 | Command Opcode : 0x0401

10:32:12.463 --

10:32:12.766 Incoming Dump:

10:32:12.766 0000: 04 02 0f 01 27 0e dd 18 b3 e4 01 02 00 0c 01 7c ....'..........|

10:32:12.766 0010: 1c 3d .=

10:32:12.766 --

10:32:12.766 Packet "HCI_Inquiry_Result_Event", Opcode 0x0002

10:32:12.766 Parameters:

10:32:12.766 | Number of Responses : 0x01

10:32:12.766 | BD_ADDR responded : "E4:B3:18:DD:0E:27"

10:32:12.766 | Page Scan Repetition Mode : 0x01 (R1)

10:32:12.766 | Page Scan Period Mode : 0x02 (P2)

10:32:12.766 | Page Scan Mode : 0x00 (Mandatory)

10:32:12.766 | Class of Device : 0x7c010c

10:32:12.766 | Clock Offset : 0x3d1c

10:32:12.766 --

10:32:15.354 Incoming Dump:

10:32:15.354 0000: 04 02 0f 01 8e ca 14 96 a0 00 01 00 00 00 00 00 ................

10:32:15.354 0010: 6c 6d lm

10:32:15.355 --

10:32:15.355 Packet "HCI_Inquiry_Result_Event", Opcode 0x0002

10:32:15.355 Parameters:

10:32:15.355 | Number of Responses : 0x01

10:32:15.355 | BD_ADDR responded : "00:A0:96:14:CA:8E"

10:32:15.355 | Page Scan Repetition Mode : 0x01 (R1)

10:32:15.355 | Page Scan Period Mode : 0x00 (P0)

10:32:15.355 | Page Scan Mode : 0x00 (Mandatory)

10:32:15.355 | Class of Device : 0x000000

10:32:15.355 | Clock Offset : 0x6d6c

10:32:15.355 --

10:32:16.473 Incoming Dump:

10:32:16.473 0000: 04 02 0f 01 8c a6 be 99 66 c4 01 02 00 0c 02 5a ........f......Z

10:32:16.473 0010: 16 11 ..

10:32:16.473 --

10:32:16.473 Packet "HCI_Inquiry_Result_Event", Opcode 0x0002

10:32:16.473 Parameters:

10:32:16.473 | Number of Responses : 0x01

10:32:16.473 | BD_ADDR responded : "C4:66:99:BE:A6:8C"

10:32:16.473 | Page Scan Repetition Mode : 0x01 (R1)

10:32:16.473 | Page Scan Period Mode : 0x02 (P2)

10:32:16.473 | Page Scan Mode : 0x00 (Mandatory)

10:32:16.473 | Class of Device : 0x5a020c

10:32:16.473 | Clock Offset : 0x1116

10:32:16.473 --

10:32:22.704 Incoming Dump:

10:32:22.704 0000: 04 01 01 00 ....

10:32:22.704 --

10:32:22.704 Packet "HCI_Inquiry_Complete_Event", Opcode 0x0001

10:32:22.704 Parameters:

10:32:22.704 | Status : 0x00 (Success)

10:32:22.704 --

10:33:14.525 *** Script Started: "D:\Installation\TI\Script _init_.txt" ***

10:33:14.525 --

10:33:14.525 Packet "HCI_Change_Local_Name", Opcode 0x0c13

10:33:14.525 Parameters:

10:33:14.525 | New name : "Bluetooth By Texas Instruments"

10:33:14.525 --

10:33:14.525 Outgoing Dump:

10:33:14.525 0000: 01 13 0c f8 42 6c 75 65 74 6f 6f 74 68 20 42 79 ....Bluetooth By

10:33:14.525 0010: 20 54 65 78 61 73 20 49 6e 73 74 72 75 6d 65 6e Texas Instrumen

10:33:14.525 0020: 74 73 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ts..............

10:33:14.525 0030: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................

10:33:14.525 0040: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................

10:33:14.525 0050: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................

10:33:14.525 0060: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................

10:33:14.525 0070: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................

10:33:14.525 0080: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................

10:33:14.525 0090: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................

10:33:14.525 00a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................

10:33:14.525 00b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................

10:33:14.525 00c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................

10:33:14.525 00d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................

10:33:14.525 00e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................

10:33:14.525 00f0: 00 00 00 00 00 00 00 00 00 00 00 00 ............

10:33:14.552 Incoming Dump:

10:33:14.552 0000: 04 0e 04 01 13 0c 00 .......

10:33:14.552 --

10:33:14.552 Packet "HCI_Command_Complete_Change_Local_Name_Event", Opcode 0x0c13

10:33:14.552 Parameters:

10:33:14.552 | Number HCI commands : 0x01

10:33:14.552 | Command Opcode : 0x0c13

10:33:14.552 | Status : 0x00 (Success)

10:33:14.552 --

10:33:14.552 Packet "HCI_Read_Local_Name", Opcode 0x0c14

10:33:14.552 --

10:33:14.552 Outgoing Dump:

10:33:14.552 0000: 01 14 0c 00 ....

10:33:14.591 Incoming Dump:

10:33:14.591 0000: 04 0e fc 01 14 0c 00 42 6c 75 65 74 6f 6f 74 68 .......Bluetooth

10:33:14.591 0010: 20 42 79 20 54 65 78 61 73 20 49 6e 73 74 72 75 By Texas Instru

10:33:14.591 0020: 6d 65 6e 74 73 00 d0 1f a7 ed e7 da 3a c5 5e e6 ments.......:.^.

10:33:14.591 0030: 1d 0f ad 29 d5 da 88 49 6c 27 89 ef bb 2f b3 ab ...)...Il'.../..

10:33:14.591 0040: 11 da 6e b0 a1 e8 be cc 18 90 ca 59 37 df 9e 8f ..n........Y7...

10:33:14.591 0050: f2 a9 e6 6c 4b 87 86 23 b2 c4 f9 51 b9 fe dc ef ...lK..#...Q....

10:33:14.591 0060: e7 e1 f0 40 a7 fc 89 79 ea 0b 66 da 70 fd 9a 45 ...@...y..f.p..E

10:33:14.591 0070: f3 37 7d d3 95 7a 7b 27 d7 82 ed 5c 49 dd e5 b3 .7}..z{'...\I...

10:33:14.591 0080: 59 5d 24 f8 1e bb 3f d5 91 ff 77 81 f2 c6 7e 7d Y]$...?...w...~}

10:33:14.591 0090: 17 de 1e 1c 78 6a 9d 17 95 f0 6c c9 d9 88 26 0b ....xj....l...&.

10:33:14.591 00a0: 8e e5 c7 91 32 75 21 58 42 96 1f db f2 87 1b f3 ....2u!XB.......

10:33:14.591 00b0: c7 1f 71 38 74 7f 78 ef ad a7 d6 1b 0c f9 ab 34 ..q8t.x........4

10:33:14.591 00c0: a8 b3 18 41 8b 7b 5b a9 0e 41 ee 9c cf 09 d6 ff ...A.{[..A......

10:33:14.591 00d0: b9 f8 c5 f9 d7 03 51 b2 7e 53 b2 46 8b b0 df 60 ......Q.~S.F...`

10:33:14.591 00e0: 8d 4a 33 b3 fd de fb 84 d9 a9 51 61 c6 7d 9c e3 .J3.......Qa.}..

10:33:14.591 00f0: 69 60 f8 2b 17 ce 0d c0 81 f3 ba 09 15 87 73 i`.+..........s

10:33:14.591 --

10:33:14.591 Packet "HCI_Command_Complete_Read_Local_Name_Event", Opcode 0x0c14

10:33:14.591 Parameters:

10:33:14.591 | Number HCI commands : 0x01

10:33:14.591 | Command Opcode : 0x0c14

10:33:14.591 | Status : 0x00 (Success)

10:33:14.591 | Local Name : "Bluetooth By Texas Instruments"

10:33:14.591 --

10:33:14.591 Packet "HCI_Write_Scan_Enable", Opcode 0x0c1a

10:33:14.591 Parameters:

10:33:14.591 | Scan Enable : 0x03 (Page and Inquiry Scan)

10:33:14.591 --

10:33:14.591 Outgoing Dump:

10:33:14.591 0000: 01 1a 0c 01 03 .....

10:33:14.607 Incoming Dump:

10:33:14.607 0000: 04 0e 04 01 1a 0c 00 .......

10:33:14.607 --

10:33:14.607 Packet "HCI_Command_Complete_Write_Scan_Enable_Event", Opcode 0x0c1a

10:33:14.607 Parameters:

10:33:14.607 | Number HCI commands : 0x01

10:33:14.607 | Command Opcode : 0x0c1a

10:33:14.607 | Status : 0x00 (Success)

10:33:14.607 --

10:33:14.607 Packet "HCI_Read_Scan_Enable", Opcode 0x0c19

10:33:14.607 --

10:33:14.607 Outgoing Dump:

10:33:14.607 0000: 01 19 0c 00 ....

10:33:14.623 Incoming Dump:

10:33:14.623 0000: 04 0e 05 01 19 0c 00 03 ........

10:33:14.623 --

10:33:14.623 Packet "HCI_Command_Complete_Read_Scan_Enable_Event", Opcode 0x0c19

10:33:14.623 Parameters:

10:33:14.623 | Number HCI commands : 0x01

10:33:14.623 | Command Opcode : 0x0c19

10:33:14.623 | Status : 0x00 (Success)

10:33:14.623 | Scan Enable : 0x03 (Page and Inquiry Scan)

10:33:14.623 --

10:33:14.623 *** Script End ***

10:33:14.623 --

10:33:39.724 --

10:33:39.724 Packet "HCI_Inquiry", Opcode 0x0401

10:33:39.724 Parameters:

10:33:39.724 | LAP : "9E8B33"

10:33:39.724 | Inquiry Length : 0x08

10:33:39.724 | Number of Responses : 0x00

10:33:39.724 --

10:33:39.724 Outgoing Dump:

10:33:39.725 0000: 01 01 04 05 33 8b 9e 08 00 ....3....

10:33:39.740 Incoming Dump:

10:33:39.740 0000: 04 0f 04 00 01 01 04 .......

10:33:39.740 --

10:33:39.740 Packet "HCI_Command_Status_Event", Opcode 0x000f

10:33:39.740 Parameters:

10:33:39.740 | Status : 0x00 (Success)

10:33:39.740 | Number HCI commands : 0x01

10:33:39.740 | Command Opcode : 0x0401

10:33:39.740 --

10:33:49.982 Incoming Dump:

10:33:49.982 0000: 04 01 01 00 ....

10:33:49.982 --

10:33:49.982 Packet "HCI_Inquiry_Complete_Event", Opcode 0x0001

10:33:49.982 Parameters:

10:33:49.982 | Status : 0x00 (Success)

10:33:49.982 --

0 Vihang Parmar over 7 years ago in reply to Dietmar Sierk

TI__Mastermind 29311 points

Dietmar,

The logs you have attached are just the UART traffic captured in the HCITester. It does not contain the information necessary to understand the issue. Please follow the Logger User's Guide (link above in the original reply) to capture the complete Bluetooth firmware logs from the device.

Best regards,
Vihang

0 Dietmar Sierk over 7 years ago in reply to Vihang Parmar

Prodigy 80 points

The currently used CC2564 evaluation board contains a so called "header connector", which is not documented in the manual.

Could you give me de schematic or pin number for the TX-Debug ping?

Thanks.

Dietmar

0 Vihang Parmar over 7 years ago in reply to Dietmar Sierk

TI__Mastermind 29311 points

Dietmar,

Which evaluation board are you using? Is it the CC256XQFNEM? If yes, you can find the schematics and User's Guide (link below) on the product page.

Schematics : http://www.ti.com/lit/zip/tidc065

User's Guide : http://www.ti.com/lit/pdf/swru450

You can refer to the Table 4. Debug Header Pinout of the User's Guide for the location of the TX_DBG signal on the debug header. For more details, you can refer to the board schematic in the design files.

Best regards,

Vihang

0 Dietmar Sierk over 7 years ago in reply to Vihang Parmar

Prodigy 80 points

Hi,

after writing the write scan enable command, the chipset send cyclically some messages., which does not stop.

I hope, you can download the log file?

Fullscreen Test_1.log Download

2-10�
�k1![�	
��1![�
�2![�5
�H2![oM
��2![�R
��2![�X
��2![7e"
�
3![Qj!]
��3![AP ��?^
��3![AP��$If�S�_
��3![AP ��`
��3![A@�a
��3![AP �
b
��3![AP �
c
��3![AP �
d
��3![AP ��e
��3![AP ��f
��3![AP �vg
��3![AP���Ih
��3![AP���Ii
��3![AP ��j
��3![AP ��k
��3![AP ��l
��3![AP��Zbm
��3![AP ��n
��3![AP��Zbo
��3![AP��zp
��3![AP�Y��q
��3![AP ��r
��3![AP �s
��3![AP �:t
��3![AP �_u
��3![A@��v
��3![A@�w
��3![AP �x
��3![AP �(y
��3![A@��z
��3![AP �?{
��3![AP ��
|
��3![AP ��
}
��3![AP��~
��3![AP��-�
��3![AP�9���
��3![AP�6�p�
��3![AP�p�b�
��3![AP ��
��3![AP ��
��3![AP �
�
��3![AP ��
��3![AP �$
��3![b�!&
��3![b�%�
��3![c@�~�
��3![cP �R�
��3![c@��
��3![cP ���
��3![cP���
��3![cP ���
��3![cP �p�
��3![cP �%�
��3![�P ��
��3![�P �b�
��3![�P ��
��3![�P ��
��3![�P ��
��3![�P �9�
��3![�P ��
��3![�P ��
��3![�P �b�
��3![�P ��
��3![�P ��
��3![�P ��
��3![�P �9�
��3![�P ��
��3![P ��
��3![P �b�
��3![P ��
��3![P ��
��3![P ��
��3![P �9�
��3![P ��
��3![PP ��
��3![PP �b�
��3![PP ��
��3![PP ��
��3![PP ��
��3![PP �9�
��3![PP ��
��3![�P ��
��3![�P �b�
��3![�P ��
��3![�P ��
��3![�P ��
��3![�P �9�
��3![�P ��
��3![�P ��
��3![�P �b�
��3![�P ��
��3![�P ��
��3![�P ��
��3![�P �9�
��3![�P ��
��3![	P ��
��3![	P �b�
��3![	P ��
��3![	P ��
��3![	P ��
��3![	P �9�
��3![	P ��
��3![<P ��
��3![=P �b�
��3![=P ��
��3![=P ��
��3![=P ��
��3![=P 9�
��3![=P �
��3![yP �
��3![yP b�
��3![�P �
��3![�P �
��3![�P �
��3![�P 9�
��3![�P �
��3![�P 	�
��3![�P 
b�
��3![�P �
��3![�P �
��3![�P 
�
��3![�P 9�
��3![�P �
��3![�P �
��3![�P b�
��3![�P �
��3![�P �
��3![�P �
��3![�P 9�
��3![�P �
��3![CP �
��3![CP b�
��3![CP �
��3![CP �
��3![CP �
��3![CP 9�
��3![CP �
��3![vP �
��3![vP b�
��3![vP  �
��3![vP !�
��3![vP "�
��3![vP #9�
��3![vP $�
��3![�P %�
��3![�P &b�
��3![�P '�
��3![�P (�
��3![�P )�
��3![�P *9�
��3![�P +�
��3![�P ,�
��3![�P -b�
��3![�P .�
��3![�P /�
��3![�P 0�
��3![�P 19�
��3![�P 2�
��3![1P 3�
��3![1P 4b�
��3![2P 5�
��3![2P 6�
��3![2P 7�
��3![2P 89�
��3![2P 9�
��3![eP :�
��3![eP ;b�
��3![eP <�
��3![eP =�
��3![eP >�
��3![eP ?9�
��3![eP @F*LPS Comeplete. Energy Detection Result = 2�Chcic_get_num_of_host_commands. Total free = 3, Reported to host = 1�random 0xe070 0x6216�I2C doesn't exist !vRef Clock is valid for PLLj"In lc_rf_init_periodic_calibration`,	0x00387135	0x00387135	HCI_Read_Scan_Enable	#	0x0033AC83	0x0033AC83	HCI_Inquiry	first byte recevied 1�random 0xa436 0x1470�6synch event REG received, module RF_CALIBRATION, msi 0a4synch event REG received, module INQUIRY SCAN, msi 1�PHY FW Version 3.27|$Calibration started. Vector=0x1, 0x0{3uart_hci parameters: UartDIV=4, OS=17, SP=63, MoB=7]PCommand Name:HCI_Write_Scan_Enable

Scan Enable = 0x03 (Page and Inquiry Scan)#	0x003443FD	0x003443FD	HCI_Inquiry		!Uart Active Protocol: H4 PROTOCOL�MRA Soft GeminiqPLL Clock Output is OKk4synch cmd return event STARTED,module RF_CALIBRATIONcEtemperature sensing: temp 18, read 0x24, vbe 0x29f6649, slope 0x1f053^-	0x00005574	0x00005574	HCI_Write_Scan_Enable	$#	0x0037DABB	0x0037DABB	HCI_Inquiry	random 0x2d9f 0x38d~XTAL wakeup mode  is disabledi#	0x00357F28	0x00357F28	HCI_Inquiry	2synch cmd return event STARTED,module INQUIRY SCAN�random 0xe917 0x1fba}lm_lc_set_brcst_retrans�Event Name: HCI_Command_Complete_Write_Scan_Enable_Event

Number HCI commands = 0x01
Command Opcode = 0x0c1a
Status = 0x00 (Success)%GCommand Name:HCI_Write_Scan_Enable

Scan Enable = 0x01 (Inquiry Scan)!7synch event FINISH received, module INQUIRY SCAN, msi 1�(HCI Send Event: HCI_COMMAND_COMPLETE_EVT�lm_lc_rf_periodic_calibrationz-ARM Clock = 40000000 Hz, Slow Clock: Externaln7synch cmd start instance, module RF_CALIBRATION, msi: 0b#Command Name:HCI_Read_Scan_Enable
lm_lc_generate_rand�Chip revision: 6f5synch cmd start instance, module INQUIRY SCAN, msi: 1�-	0x00365FC0	0x00365FC0	HCI_Write_Scan_Enable	Deactivating timer: initylm_lc_get_local_bd_addrwUART HCI baudrate = 116363pPLL Clock Out = 40000000 HzlCCommand Name:HCI_Write_Scan_Enable

Scan Enable = 0x00 (No Scans)_Command Name:HCI_Inquiry

LAP = "9E:8B:33"
Inquiry Length = 0x04
Number of Responses = 0x00lm_lc_start_inquiry_scan�Fhcic_process_hci_commands: HCI_WRITE_SCAN_ENABLE (Group 3 Opcode 0x1a)�+Disable FLIGHT MODE - Enable TX calibration�9synch event FINISH received, module RF_CALIBRATION, msi 0�-	0x0038BD19	0x0038BD19	HCI_Write_Scan_Enable	"-	0x00372E41	0x00372E41	HCI_Write_Scan_Enable	(LC_PICONIZER - allocated network clock 1�"Transport detection: UART detected�Process type: NominaleTemperature region = 5_Software version - 7.0.16xSelf Test passedulm_lc_self_test_run_init_teststOCP Clock = 8000000 HzoDetected Clock = 38400000 Hzg
ORCA Platformdrandom 0xf139 0xd78dClock Working mode: PLL ModemRef Clock = 38400000 Hzh$lm_lc_gemini_coex_notify_scan_status�lm_lc_get_local_featuresrD	0x00005574	0x00005574		HCI_Command_Complete_Write_Scan_Enable_Event&

0 Dietmar Sierk over 7 years ago in reply to Dietmar Sierk

Prodigy 80 points

Hallo,

there is a complete set of log files from HCI-tester and Logger tool.

My test sequence was a follow:

power on -> inquiry (result ok) -> write scan enable for inquiry and page (answer success, but does not work) -> inquiry (does not work) -> write scan enable for no scan (answer success) -> inquiry (does not work)

Thank you for your help.

Dietmar

(I had to rename the file name extension (.Logger_test inquiry .txt

Fullscreen HCITester test inquiry.htm Download

<HTML>
<HEAD>
<TITLE>HCITester Log</TITLE>
</HEAD>
<BODY>
<FONT face="Courier New">
<TABLE ALIGN=LEFT CELLSPACING=0 width=3500 CELLPADDING=0>
<tr bgcolor="ffffe6"><td><font color="0000c0">14:35:28.295 --</font></td></tr>
<tr bgcolor="ffffe6"><td><font color="0000c0">14:35:28.295 Packet "HCI_Inquiry", Opcode 0x0401</font></td></tr>
<tr bgcolor="ffffe6"><td><font color="0000c0">14:35:28.295 Parameters:</font></td></tr>
<tr bgcolor="ffffe6"><td><font color="0000c0">14:35:28.295 | LAP                 : "9E8B33"</font></td></tr>
<tr bgcolor="ffffe6"><td><font color="0000c0">14:35:28.295 | Inquiry Length      : 0x04</font></td></tr>
<tr bgcolor="ffffe6"><td><font color="0000c0">14:35:28.295 | Number of Responses : 0x00</font></td></tr>
<tr bgcolor="ffffe6"><td><font color="0000c0">14:35:28.295 --</font></td></tr>
<tr bgcolor="60c0c0"><td><font color="ffffff">14:35:28.295 Outgoing Dump:</font></td></tr>
<tr bgcolor="60c0c0"><td><font color="ffffff">14:35:28.295     0000: 01 01 04 05 33 8b 9e 04 00                      ....3....</font></td></tr>
<tr bgcolor="408080"><td><font color="ffffff">14:35:28.297 Incoming Dump:</font></td></tr>
<tr bgcolor="408080"><td><font color="ffffff">14:35:28.297     0000: 04 0f                                           ..</font></td></tr>
<tr bgcolor="408080"><td><font color="ffffff">14:35:28.313 Incoming Dump:</font></td></tr>
<tr bgcolor="408080"><td><font color="ffffff">14:35:28.313     0000: 04 00 01 01 04                                  .....</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:35:28.313 --</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:35:28.313 Packet "HCI_Command_Status_Event", Opcode 0x000f</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:35:28.313 Parameters:</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:35:28.313 | Status              : 0x00 (Success)</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:35:28.313 | Number HCI commands : 0x01</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:35:28.313 | Command Opcode      : 0x0401</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:35:28.313 --</font></td></tr>
<tr bgcolor="408080"><td><font color="ffffff">14:35:28.552 Incoming Dump:</font></td></tr>
<tr bgcolor="408080"><td><font color="ffffff">14:35:28.552     0000: 04 02 0f 01 27 0e dd 18 b3 e4 01 02 00 0c 01 7c ....'..........|</font></td></tr>
<tr bgcolor="408080"><td><font color="ffffff">14:35:28.552     0010: 54 2b                                           T+</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:35:28.552 --</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:35:28.552 Packet "HCI_Inquiry_Result_Event", Opcode 0x0002</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:35:28.552 Parameters:</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:35:28.552 | Number of Responses       : 0x01</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:35:28.552 | BD_ADDR responded         : "E4:B3:18:DD:0E:27"</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:35:28.552 | Page Scan Repetition Mode : 0x01 (R1)</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:35:28.552 | Page Scan Period Mode     : 0x02 (P2)</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:35:28.552 | Page Scan Mode            : 0x00 (Mandatory)</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:35:28.552 | Class of Device           : 0x7c010c</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:35:28.552 | Clock Offset              : 0x2b54</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:35:28.552 --</font></td></tr>
<tr bgcolor="408080"><td><font color="ffffff">14:35:33.393 Incoming Dump:</font></td></tr>
<tr bgcolor="408080"><td><font color="ffffff">14:35:33.393     0000: 04 02 0f 01 8e ca 14 96 a0 00 01 00 00 00 00 00 ................</font></td></tr>
<tr bgcolor="408080"><td><font color="ffffff">14:35:33.393     0010: 0c 4c                                           .L</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:35:33.394 --</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:35:33.394 Packet "HCI_Inquiry_Result_Event", Opcode 0x0002</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:35:33.394 Parameters:</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:35:33.394 | Number of Responses       : 0x01</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:35:33.394 | BD_ADDR responded         : "00:A0:96:14:CA:8E"</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:35:33.394 | Page Scan Repetition Mode : 0x01 (R1)</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:35:33.394 | Page Scan Period Mode     : 0x00 (P0)</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:35:33.394 | Page Scan Mode            : 0x00 (Mandatory)</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:35:33.394 | Class of Device           : 0x000000</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:35:33.394 | Clock Offset              : 0x4c0c</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:35:33.394 --</font></td></tr>
<tr bgcolor="408080"><td><font color="ffffff">14:35:33.425 Incoming Dump:</font></td></tr>
<tr bgcolor="408080"><td><font color="ffffff">14:35:33.425     0000: 04 01 01 00                                     ....</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:35:33.425 --</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:35:33.425 Packet "HCI_Inquiry_Complete_Event", Opcode 0x0001</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:35:33.425 Parameters:</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:35:33.425 | Status : 0x00 (Success)</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:35:33.425 --</font></td></tr>
<tr bgcolor="ffffe6"><td><font color="0000c0">14:37:40.660 --</font></td></tr>
<tr bgcolor="ffffe6"><td><font color="0000c0">14:37:40.660 Packet "HCI_Write_Scan_Enable", Opcode 0x0c1a</font></td></tr>
<tr bgcolor="ffffe6"><td><font color="0000c0">14:37:40.660 Parameters:</font></td></tr>
<tr bgcolor="ffffe6"><td><font color="0000c0">14:37:40.660 | Scan Enable : 0x03 (Page and Inquiry Scan)</font></td></tr>
<tr bgcolor="ffffe6"><td><font color="0000c0">14:37:40.660 --</font></td></tr>
<tr bgcolor="60c0c0"><td><font color="ffffff">14:37:40.660 Outgoing Dump:</font></td></tr>
<tr bgcolor="60c0c0"><td><font color="ffffff">14:37:40.660     0000: 01 1a 0c 01 03                                  .....</font></td></tr>
<tr bgcolor="408080"><td><font color="ffffff">14:37:40.669 Incoming Dump:</font></td></tr>
<tr bgcolor="408080"><td><font color="ffffff">14:37:40.669     0000: 04 0e 04 01 1a 0c 00                            .......</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:37:40.669 --</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:37:40.669 Packet "HCI_Command_Complete_Write_Scan_Enable_Event", Opcode 0x0c1a</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:37:40.669 Parameters:</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:37:40.669 | Number HCI commands : 0x01</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:37:40.669 | Command Opcode      : 0x0c1a</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:37:40.669 | Status              : 0x00 (Success)</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:37:40.669 --</font></td></tr>
<tr bgcolor="ffffe6"><td><font color="0000c0">14:38:05.139 --</font></td></tr>
<tr bgcolor="ffffe6"><td><font color="0000c0">14:38:05.139 Packet "HCI_Inquiry", Opcode 0x0401</font></td></tr>
<tr bgcolor="ffffe6"><td><font color="0000c0">14:38:05.139 Parameters:</font></td></tr>
<tr bgcolor="ffffe6"><td><font color="0000c0">14:38:05.139 | LAP                 : "9E8B33"</font></td></tr>
<tr bgcolor="ffffe6"><td><font color="0000c0">14:38:05.139 | Inquiry Length      : 0x04</font></td></tr>
<tr bgcolor="ffffe6"><td><font color="0000c0">14:38:05.139 | Number of Responses : 0x00</font></td></tr>
<tr bgcolor="ffffe6"><td><font color="0000c0">14:38:05.139 --</font></td></tr>
<tr bgcolor="60c0c0"><td><font color="ffffff">14:38:05.139 Outgoing Dump:</font></td></tr>
<tr bgcolor="60c0c0"><td><font color="ffffff">14:38:05.139     0000: 01 01 04 05 33 8b 9e 04 00                      ....3....</font></td></tr>
<tr bgcolor="408080"><td><font color="ffffff">14:38:05.144 Incoming Dump:</font></td></tr>
<tr bgcolor="408080"><td><font color="ffffff">14:38:05.144     0000: 04 0f 04 00 01 01 04                            .......</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:38:05.144 --</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:38:05.144 Packet "HCI_Command_Status_Event", Opcode 0x000f</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:38:05.144 Parameters:</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:38:05.144 | Status              : 0x00 (Success)</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:38:05.144 | Number HCI commands : 0x01</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:38:05.144 | Command Opcode      : 0x0401</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:38:05.144 --</font></td></tr>
<tr bgcolor="408080"><td><font color="ffffff">14:38:10.272 Incoming Dump:</font></td></tr>
<tr bgcolor="408080"><td><font color="ffffff">14:38:10.272     0000: 04 01 01 00                                     ....</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:38:10.272 --</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:38:10.272 Packet "HCI_Inquiry_Complete_Event", Opcode 0x0001</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:38:10.272 Parameters:</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:38:10.272 | Status : 0x00 (Success)</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:38:10.272 --</font></td></tr>
<tr bgcolor="ffffe6"><td><font color="0000c0">14:38:20.947 --</font></td></tr>
<tr bgcolor="ffffe6"><td><font color="0000c0">14:38:20.948 Packet "HCI_Write_Scan_Enable", Opcode 0x0c1a</font></td></tr>
<tr bgcolor="ffffe6"><td><font color="0000c0">14:38:20.948 Parameters:</font></td></tr>
<tr bgcolor="ffffe6"><td><font color="0000c0">14:38:20.948 | Scan Enable : 0x00 (No Scans)</font></td></tr>
<tr bgcolor="ffffe6"><td><font color="0000c0">14:38:20.948 --</font></td></tr>
<tr bgcolor="60c0c0"><td><font color="ffffff">14:38:20.948 Outgoing Dump:</font></td></tr>
<tr bgcolor="60c0c0"><td><font color="ffffff">14:38:20.948     0000: 01 1a 0c 01 00                                  .....</font></td></tr>
<tr bgcolor="408080"><td><font color="ffffff">14:38:20.956 Incoming Dump:</font></td></tr>
<tr bgcolor="408080"><td><font color="ffffff">14:38:20.956     0000: 04 0e 04 01 1a 0c 00                            .......</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:38:20.956 --</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:38:20.956 Packet "HCI_Command_Complete_Write_Scan_Enable_Event", Opcode 0x0c1a</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:38:20.956 Parameters:</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:38:20.956 | Number HCI commands : 0x01</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:38:20.956 | Command Opcode      : 0x0c1a</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:38:20.956 | Status              : 0x00 (Success)</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:38:20.956 --</font></td></tr>
<tr bgcolor="ffffe6"><td><font color="0000c0">14:38:49.168 --</font></td></tr>
<tr bgcolor="ffffe6"><td><font color="0000c0">14:38:49.168 Packet "HCI_Inquiry", Opcode 0x0401</font></td></tr>
<tr bgcolor="ffffe6"><td><font color="0000c0">14:38:49.168 Parameters:</font></td></tr>
<tr bgcolor="ffffe6"><td><font color="0000c0">14:38:49.168 | LAP                 : "9E8B33"</font></td></tr>
<tr bgcolor="ffffe6"><td><font color="0000c0">14:38:49.168 | Inquiry Length      : 0x04</font></td></tr>
<tr bgcolor="ffffe6"><td><font color="0000c0">14:38:49.168 | Number of Responses : 0x00</font></td></tr>
<tr bgcolor="ffffe6"><td><font color="0000c0">14:38:49.168 --</font></td></tr>
<tr bgcolor="60c0c0"><td><font color="ffffff">14:38:49.168 Outgoing Dump:</font></td></tr>
<tr bgcolor="60c0c0"><td><font color="ffffff">14:38:49.168     0000: 01 01 04 05 33 8b 9e 04 00                      ....3....</font></td></tr>
<tr bgcolor="408080"><td><font color="ffffff">14:38:49.173 Incoming Dump:</font></td></tr>
<tr bgcolor="408080"><td><font color="ffffff">14:38:49.173     0000: 04 0f 04 00 01 01 04                            .......</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:38:49.173 --</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:38:49.173 Packet "HCI_Command_Status_Event", Opcode 0x000f</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:38:49.173 Parameters:</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:38:49.173 | Status              : 0x00 (Success)</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:38:49.173 | Number HCI commands : 0x01</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:38:49.173 | Command Opcode      : 0x0401</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:38:49.173 --</font></td></tr>
<tr bgcolor="408080"><td><font color="ffffff">14:38:54.301 Incoming Dump:</font></td></tr>
<tr bgcolor="408080"><td><font color="ffffff">14:38:54.301     0000: 04 01 01 00                                     ....</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:38:54.301 --</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:38:54.301 Packet "HCI_Inquiry_Complete_Event", Opcode 0x0001</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:38:54.301 Parameters:</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:38:54.301 | Status : 0x00 (Success)</font></td></tr>
<tr bgcolor="fff7fa"><td><font color="006400">14:38:54.301 --</font></td></tr>
</TABLE>
</FONT>
</BODY>
</HTML>

for uploading these files)

0 Vihang Parmar over 7 years ago in reply to Dietmar Sierk

TI__Mastermind 29311 points

Dietmar,

From the logs, it looks like you are issuing HCI_Inquiry command right after the device power-up. You must download the service-pack after the device power-up to initialize the device.

You can find the CC256xB service-pack at this link : CC256XB-BT-SP

Best regards,
Vihang

0 Dietmar Sierk over 7 years ago in reply to Vihang Parmar

Prodigy 80 points

Hallo,

thank’s for your answer, but didn’t solve the issue.

The service pack contains three bts script files, which are not executable in the HCT-tester suite. Also an individually execution of the HCI commands (except the patch) didn’t change the situation regarding the “Write scan enable” or inquiry, after write scan enable.

If the CC2564 does need some special initialization commands to reach a state where HCI commands work properly, please provide a discrete list of these commands, a executable script for your HCI-Test suite or reference a document which describes the initialization phase.

Thanks,

Dietmar

0 Dietmar Sierk over 7 years ago in reply to Vihang Parmar

Prodigy 80 points

se below.

0 Vihang Parmar over 7 years ago in reply to Dietmar Sierk

TI__Mastermind 29311 points

Hello Dietmar,

I wanted to post the update to this thread that the issue was resolved offline. The solution was to download the service-pack successfully to the CC2564MODN using the HCITester before sending any test commands (i.e. HCI_Write_Scan_Enable).

Best regards,
Vihang

Bluetooth®︎

Bluetooth forum

CC2564: HCI commands inquiry and write scan enable - behaviour