Part Number: CC2652R
Other Parts Discussed in Thread: SMARTRFTM-STUDIO, Z-STACK, SYSCONFIG
Hi,
I would like to know if TI provides any firmware for 802.15.4 RF testing with CC2652R? For example, for BLE, I use host_test with HCI command.
Thanks,
Koon
Hi Ryan,
I have attached a screen capture of CCS ver 9.3 with the error message. I also include ti_radio_config.c/h that I generate from smart studio.
Koon
//*********************************************************************************
// Generated by SmartRF Studio version 2.16.0 (build#215)
// The applied template is compatible with CC26x2 SDK version 2.10.xx.xx or newer.
// Device: CC2652R Rev. E (2.1).
//
//*********************************************************************************
//*********************************************************************************
// Parameter summary
// IEEE Channel: 11
// Frequency: 2405 MHz
// SFD: 0
// Packet Data: 255
// Preamble (32 bit): 01010101...
// TX Power: 5 dBm
#include <ti/devices/DeviceFamily.h>
#include DeviceFamily_constructPath(driverlib/rf_mailbox.h)
#include DeviceFamily_constructPath(driverlib/rf_common_cmd.h)
#include DeviceFamily_constructPath(driverlib/rf_ieee_cmd.h)
#include <ti/drivers/rf/RF.h>
#include DeviceFamily_constructPath(rf_patches/rf_patch_cpe_ieee_802_15_4.h)
#include "ti_radio_config.h"
// TI-RTOS RF Mode Object
RF_Mode RF_prop =
{
.rfMode = RF_MODE_AUTO,
.cpePatchFxn = &rf_patch_cpe_ieee_802_15_4,
.mcePatchFxn = 0,
.rfePatchFxn = 0
};
// Overrides for CMD_RADIO_SETUP
uint32_t pOverrides[] =
{
// override_ieee_802_15_4.xml
// DC/DC regulator: In Tx, use DCDCCTL5[3:0]=0x3 (DITHER_EN=0 and IPEAK=3).
(uint32_t)0x00F388D3,
// Rx: Set LNA bias current offset to +15 to saturate trim to max (default: 0)
(uint32_t)0x000F8883,
(uint32_t)0xFFFFFFFF
};
// CMD_RADIO_SETUP
// Radio Setup Command for Pre-Defined Schemes
rfc_CMD_RADIO_SETUP_t RF_cmdRadioSetup =
{
.commandNo = 0x0802,
.status = 0x0000,
.pNextOp = 0, // INSERT APPLICABLE POINTER: (uint8_t*)&xxx
.startTime = 0x00000000,
.startTrigger.triggerType = 0x0,
.startTrigger.bEnaCmd = 0x0,
.startTrigger.triggerNo = 0x0,
.startTrigger.pastTrig = 0x0,
.condition.rule = 0x1,
.condition.nSkip = 0x0,
.mode = 0x01,
.loDivider = 0x00,
.config.frontEndMode = 0x0,
.config.biasMode = 0x0,
.config.analogCfgMode = 0x0,
.config.bNoFsPowerUp = 0x0,
.txPower = 0x7217,
.pRegOverride = pOverrides
};
// CMD_FS
// Frequency Synthesizer Programming Command
rfc_CMD_FS_t RF_cmdFs =
{
.commandNo = 0x0803,
.status = 0x0000,
.pNextOp = 0, // INSERT APPLICABLE POINTER: (uint8_t*)&xxx
.startTime = 0x00000000,
.startTrigger.triggerType = 0x0,
.startTrigger.bEnaCmd = 0x0,
.startTrigger.triggerNo = 0x0,
.startTrigger.pastTrig = 0x0,
.condition.rule = 0x1,
.condition.nSkip = 0x0,
.frequency = 0x0965,
.fractFreq = 0x0000,
.synthConf.bTxMode = 0x1,
.synthConf.refFreq = 0x0,
.__dummy0 = 0x00,
.__dummy1 = 0x00,
.__dummy2 = 0x00,
.__dummy3 = 0x0000
};
// CMD_IEEE_TX
// IEEE 802.15.4 Transmit Command
rfc_CMD_IEEE_TX_t RF_cmdIeeeTx =
{
.commandNo = 0x2C01,
.status = 0x0000,
.pNextOp = 0, // INSERT APPLICABLE POINTER: (uint8_t*)&xxx
.startTime = 0x00000000,
.startTrigger.triggerType = 0x0,
.startTrigger.bEnaCmd = 0x0,
.startTrigger.triggerNo = 0x0,
.startTrigger.pastTrig = 0x0,
.condition.rule = 0x1,
.condition.nSkip = 0x0,
.txOpt.bIncludePhyHdr = 0x0,
.txOpt.bIncludeCrc = 0x0,
.txOpt.payloadLenMsb = 0x0,
.payloadLen = 0x1E,
.pPayload = 0, // INSERT APPLICABLE POINTER: (uint8_t*)&xxx
.timeStamp = 0x00000000
};
// CMD_IEEE_RX
// IEEE 802.15.4 Receive Command
rfc_CMD_IEEE_RX_t RF_cmdIeeeRx =
{
.commandNo = 0x2801,
.status = 0x0000,
.pNextOp = 0, // INSERT APPLICABLE POINTER: (uint8_t*)&xxx
.startTime = 0x00000000,
.startTrigger.triggerType = 0x0,
.startTrigger.bEnaCmd = 0x0,
.startTrigger.triggerNo = 0x0,
.startTrigger.pastTrig = 0x0,
.condition.rule = 0x1,
.condition.nSkip = 0x0,
.channel = 0x00,
.rxConfig.bAutoFlushCrc = 0x0,
.rxConfig.bAutoFlushIgn = 0x0,
.rxConfig.bIncludePhyHdr = 0x0,
.rxConfig.bIncludeCrc = 0x0,
.rxConfig.bAppendRssi = 0x1,
.rxConfig.bAppendCorrCrc = 0x1,
.rxConfig.bAppendSrcInd = 0x0,
.rxConfig.bAppendTimestamp = 0x0,
.pRxQ = 0, // INSERT APPLICABLE POINTER: (dataQueue_t*)&xxx
.pOutput = 0, // INSERT APPLICABLE POINTER: (uint8_t*)&xxx
.frameFiltOpt.frameFiltEn = 0x0,
.frameFiltOpt.frameFiltStop = 0x0,
.frameFiltOpt.autoAckEn = 0x0,
.frameFiltOpt.slottedAckEn = 0x0,
.frameFiltOpt.autoPendEn = 0x0,
.frameFiltOpt.defaultPend = 0x0,
.frameFiltOpt.bPendDataReqOnly = 0x0,
.frameFiltOpt.bPanCoord = 0x0,
.frameFiltOpt.maxFrameVersion = 0x3,
.frameFiltOpt.fcfReservedMask = 0x0,
.frameFiltOpt.modifyFtFilter = 0x0,
.frameFiltOpt.bStrictLenFilter = 0x0,
.frameTypes.bAcceptFt0Beacon = 0x1,
.frameTypes.bAcceptFt1Data = 0x1,
.frameTypes.bAcceptFt2Ack = 0x1,
.frameTypes.bAcceptFt3MacCmd = 0x1,
.frameTypes.bAcceptFt4Reserved = 0x1,
.frameTypes.bAcceptFt5Reserved = 0x1,
.frameTypes.bAcceptFt6Reserved = 0x1,
.frameTypes.bAcceptFt7Reserved = 0x1,
.ccaOpt.ccaEnEnergy = 0x0,
.ccaOpt.ccaEnCorr = 0x0,
.ccaOpt.ccaEnSync = 0x0,
.ccaOpt.ccaCorrOp = 0x1,
.ccaOpt.ccaSyncOp = 0x1,
.ccaOpt.ccaCorrThr = 0x0,
.ccaRssiThr = 0x64,
.__dummy0 = 0x00,
.numExtEntries = 0x00,
.numShortEntries = 0x00,
.pExtEntryList = 0, // INSERT APPLICABLE POINTER: (uint32_t*)&xxx
.pShortEntryList = 0, // INSERT APPLICABLE POINTER: (uint32_t*)&xxx
.localExtAddr = 0x0000000012345678,
.localShortAddr = 0xABBA,
.localPanID = 0x0000,
.__dummy1 = 0x000000,
.endTrigger.triggerType = 0x1,
.endTrigger.bEnaCmd = 0x0,
.endTrigger.triggerNo = 0x0,
.endTrigger.pastTrig = 0x0,
.endTime = 0x00000000
};
