U-Boot SPL 2013.04-rc1-14237-g90639fe-dirty (Apr 13 2013 - 13:57:11) musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Peripheral mode controller at 47401000 using PIO, IRQ 0 musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Host mode controller at 47401800 using PIO, IRQ 0 OMAP SD/MMC: 0 mmc_send_cmd : timeout: No status update reading u-boot.img reading u-boot.img U-Boot 2013.04-rc1-14237-g90639fe-dirty (Apr 13 2013 - 13:57:11) I2C: ready DRAM: 512 MiB WARNING: Caches not enabled NAND: No NAND device found!!! 0 MiB MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 *** Warning - readenv() failed, using default environment musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Peripheral mode controller at 47401000 using PIO, IRQ 0 musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Host mode controller at 47401800 using PIO, IRQ 0 Net: not set. Validating first E-fuse MAC cpsw, usb_ether Hit any key to stop autoboot: 0 gpio: pin 53 (gpio 53) value is 1 mmc0 is current device micro SD card found mmc0 is current device gpio: pin 54 (gpio 54) value is 1 SD/MMC found on device 0 reading uEnv.txt 2032 bytes read in 5 ms (396.5 KiB/s) Loaded environment from uEnv.txt Importing environment from mmc ... Running uenvcmd ... reading zImage 3476552 bytes read in 417 ms (8 MiB/s) reading uInitrd 2975910 bytes read in 343 ms (8.3 MiB/s) reading /dtbs/am335x-boneblack.dtb 24996 bytes read in 11 ms (2.2 MiB/s) ## Loading init Ramdisk from Legacy Image at 81000000 ... Image Name: initramfs Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 2975846 Bytes = 2.8 MiB Load Address: 00000000 Entry Point: 00000000 ## Flattened Device Tree blob at 815f0000 Booting using the fdt blob at 0x815f0000 Using Device Tree in place at 815f0000, end 815f91a3 Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 3.8.13xenomai-bone28 (alexander@thinkpad.site) (gcc version 4.7.3 20130328 (prerelease) (crosstool-NG linaro-1.13.1-4.7-2013.04-20130415 - Linaro GCC 2013.04) ) #5 SMP Fri Nov 1 19:11:02 CET 2013 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: Generic AM33XX (Flattened Device Tree), model: TI AM335x BeagleBone [ 0.000000] bootconsole [earlycon0] enabled [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] AM335X ES1.0 (neon ) [ 0.000000] PERCPU: Embedded 11 pages/cpu @c0eed000 s23552 r8192 d13312 u45056 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 117092 [ 0.000000] Kernel command line: console=ttyO0,115200n8 capemgr.disable_partno=BB-BONELT-HDMI,BB-BONE-EMMC-2G video=HDMI-A-1:800x480M@85e root=/dev/mmcblk0p2 ro rootfstype=ext4 rootwait fixrtc mem=462M ip= earlyprintk=serial vram=50M [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] __ex_table already sorted, skipping sort [ 0.000000] allocated 946176 bytes of page_cgroup [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups [ 0.000000] Memory: 461MB = 461MB total [ 0.000000] Memory: 452464k/452464k available, 20624k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xdd000000 - 0xff000000 ( 544 MB) [ 0.000000] lowmem : 0xc0000000 - 0xdce00000 ( 462 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc0986b74 (9723 kB) [ 0.000000] .init : 0xc0987000 - 0xc09d8c00 ( 327 kB) [ 0.000000] .data : 0xc09da000 - 0xc0a5e2c0 ( 529 kB) [ 0.000000] .bss : 0xc0a5e2c0 - 0xc0b3c380 ( 889 kB) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts [ 0.000000] Total of 128 interrupts on 1 active controller [ 0.000000] OMAP clockevent source: GPTIMER1 at 24000000 Hz [ 0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms [ 0.000000] I-pipe, 24.000 MHz clocksource [ 0.000000] OMAP clocksource: GPTIMER2 at 24000000 Hz [ 0.000000] Interrupt pipeline (release #3) [ 0.000000] Console: colour dummy device 80x30 [ 0.019992] Calibrating delay loop... 363.67 BogoMIPS (lpj=354304) [ 0.045709] pid_max: default: 32768 minimum: 301 [ 0.050860] Security Framework initialized [ 0.055290] Mount-cache hash table entries: 512 [ 0.070938] Initializing cgroup subsys cpuacct [ 0.075666] Initializing cgroup subsys memory [ 0.080327] Initializing cgroup subsys blkio [ 0.084987] CPU: Testing write buffer coherency: ok [ 0.090758] CPU0: thread -1, cpu 0, socket -1, mpidr 0 [ 0.096255] Setting up static identity map for 0x8069e048 - 0x8069e0a0 [ 0.104847] Brought up 1 CPUs [ 0.108050] SMP: Total of 1 processors activated (363.67 BogoMIPS). [ 0.116483] devtmpfs: initialized [ 0.185611] pinctrl core: initialized pinctrl subsystem [ 0.191385] rstctl core: initialized rstctl subsystem [ 0.197282] regulator-dummy: no parameters [ 0.202136] NET: Registered protocol family 16 [ 0.207966] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.225736] pinctrl-single 44e10800.pinmux: 142 pins at pa f9e10800 size 568 [ 0.234162] platform 49000000.edma: alias fck already exists [ 0.240139] platform 49000000.edma: alias fck already exists [ 0.246092] platform 49000000.edma: alias fck already exists [ 0.253401] OMAP GPIO hardware version 0.1 [ 0.262818] gpio-rctrl rstctl.4: loaded OK [ 0.272779] hw-breakpoint: debug architecture 0x4 unsupported. [ 0.281126] cpsw.0: No hwaddr in dt. Using c8:a0:30:b0:71:f9 from efuse [ 0.288096] cpsw.1: No hwaddr in dt. Using c8:a0:30:b0:71:fb from efuse [ 0.311701] bio: create slab at 0 [ 0.328423] edma-dma-engine edma-dma-engine.0: TI EDMA DMA engine driver [ 0.335965] vmmcsd_fixed: 3300 mV [ 0.342572] SCSI subsystem initialized [ 0.347002] usbcore: registered new interface driver usbfs [ 0.352885] usbcore: registered new interface driver hub [ 0.358789] usbcore: registered new device driver usb [ 0.366362] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz [ 0.373986] input: tps65217_pwr_but as /devices/ocp.3/44e0b000.i2c/i2c-0/0-0024/input/input0 [ 0.384856] DCDC1: at 1500 mV [ 0.389506] vdd_mpu: 925 <--> 1325 mV at 1100 mV [ 0.395717] vdd_core: 925 <--> 1150 mV at 1100 mV [ 0.401981] LDO1: at 1800 mV [ 0.406350] LDO2: at 3300 mV [ 0.411622] LDO3: 1800 mV [ 0.415713] LDO4: at 3300 mV [ 0.419949] tps65217 0-0024: TPS65217 ID 0xe version 1.2 [ 0.426405] omap_i2c 44e0b000.i2c: unable to select pin group [ 0.433329] omap_i2c 4819c000.i2c: bus 1 rev0.11 at 100 kHz [ 0.442058] omap_i2c 4819c000.i2c: unable to select pin group [ 0.448384] media: Linux media interface: v0.10 [ 0.453432] Linux video capture interface: v2.00 [ 0.458526] pps_core: LinuxPPS API ver. 1 registered [ 0.463776] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.474096] Advanced Linux Sound Architecture Driver Initialized. [ 0.481573] NetLabel: Initializing [ 0.485217] NetLabel: domain hash size = 128 [ 0.489819] NetLabel: protocols = UNLABELED CIPSOv4 [ 0.495196] NetLabel: unlabeled traffic allowed by default [ 0.501597] Switching to clocksource ipipe_tsc [ 0.564354] NET: Registered protocol family 2 [ 0.570137] TCP established hash table entries: 4096 (order: 3, 32768 bytes) [ 0.577686] TCP bind hash table entries: 4096 (order: 4, 81920 bytes) [ 0.584617] TCP: Hash tables configured (established 4096 bind 4096) [ 0.591372] TCP: reno registered [ 0.594836] UDP hash table entries: 256 (order: 1, 12288 bytes) [ 0.601087] UDP-Lite hash table entries: 256 (order: 1, 12288 bytes) [ 0.608234] NET: Registered protocol family 1 [ 0.613519] RPC: Registered named UNIX socket transport module. [ 0.619774] RPC: Registered udp transport module. [ 0.624754] RPC: Registered tcp transport module. [ 0.629716] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.636932] Trying to unpack rootfs image as initramfs... [ 1.002236] Freeing initrd memory: 2904K [ 1.007125] hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5 counters available [ 1.016033] CPU PMU: attempt to register multiple PMU devices! [ 1.021942] arm-pmu: probe of arm-pmu failed with error -28 [ 1.028556] omap2_mbox_probe: platform not supported [ 1.320985] I-pipe: head domain Xenomai registered. [ 1.326198] Xenomai: hal/arm started. [ 1.332024] Xenomai: scheduling class idle registered. [ 1.337568] Xenomai: scheduling class rt registered. [ 1.350979] Xenomai: real-time nucleus v2.6.3 (Lies and Truths) loaded. [ 1.357953] Xenomai: debug mode enabled. [ 1.362700] Xenomai: starting native API services. [ 1.367792] Xenomai: starting POSIX services. [ 1.372602] Xenomai: starting RTDM services. [ 1.378638] VFS: Disk quotas dquot_6.5.2 [ 1.383143] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 1.391488] NFS: Registering the id_resolver key type [ 1.397037] Key type id_resolver registered [ 1.401487] Key type id_legacy registered [ 1.405818] fuse init (API version 7.20) [ 1.410944] Btrfs loaded [ 1.413886] msgmni has been set to 889 [ 1.421165] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) [ 1.428942] io scheduler noop registered [ 1.433114] io scheduler deadline registered [ 1.437763] io scheduler cfq registered (default) [ 1.444770] tps65217-bl tps65217-bl: no platform data provided [ 1.450973] tps65217-bl: probe of tps65217-bl failed with error -22 [ 1.458473] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 1.467583] omap_uart 44e09000.serial: did not get pins for uart0 error: -19 [ 1.475414] 44e09000.serial: ttyO0 at MMIO 0x44e09000 (irq = 88) is a OMAP UART0 [ 1.483357] console [ttyO0] enabled, bootconsole disabled [ 1.483357] console [ttyO0] enabled, bootconsole disabled [ 1.495878] [drm] Initialized drm 1.1.0 20060810 [ 1.515249] brd: module loaded [ 1.526338] loop: module loaded [ 1.529877] at24 0-0050: 32768 byte 24c256 EEPROM, writable, 1 bytes/write [ 1.537174] at24 1-0054: 32768 byte 24c256 EEPROM, writable, 1 bytes/write [ 1.544468] at24 1-0055: 32768 byte 24c256 EEPROM, writable, 1 bytes/write [ 1.551754] at24 1-0056: 32768 byte 24c256 EEPROM, writable, 1 bytes/write [ 1.559039] at24 1-0057: 32768 byte 24c256 EEPROM, writable, 1 bytes/write [ 1.573455] bone-capemgr bone_capemgr.9: Baseboard: 'A335BNLT,0A5A,1613BBBK1042' [ 1.581308] bone-capemgr bone_capemgr.9: compatible-baseboard=ti,beaglebone-black [ 1.589221] bone-capemgr bone_capemgr.9: Skipping disabled cape with part# BB-BONE-EMMC-2G [ 1.597921] bone-capemgr bone_capemgr.9: Skipping disabled cape with part# BB-BONELT-HDMI [ 1.637281] bone-capemgr bone_capemgr.9: slot #0: No cape found [ 1.674385] bone-capemgr bone_capemgr.9: slot #1: No cape found [ 1.711493] bone-capemgr bone_capemgr.9: slot #2: No cape found [ 1.748600] bone-capemgr bone_capemgr.9: slot #3: No cape found [ 1.754860] bone-capemgr bone_capemgr.9: slot #4: specific override [ 1.761463] bone-capemgr bone_capemgr.9: bone: Using override eeprom data at slot 4 [ 1.769504] bone-capemgr bone_capemgr.9: slot #4: 'Bone-LT-eMMC-2G,00A0,Texas Instrument,BB-BONE-EMMC-2G' [ 1.779650] bone-capemgr bone_capemgr.9: slot #5: specific override [ 1.786251] bone-capemgr bone_capemgr.9: bone: Using override eeprom data at slot 5 [ 1.794285] bone-capemgr bone_capemgr.9: slot #5: 'Bone-Black-HDMI,00A0,Texas Instrument,BB-BONELT-HDMI' [ 1.804335] bone-capemgr bone_capemgr.9: slot #6: specific override [ 1.810937] bone-capemgr bone_capemgr.9: bone: Using override eeprom data at slot 6 [ 1.818979] bone-capemgr bone_capemgr.9: slot #6: 'Bone-Black-HDMIN,00A0,Texas Instrument,BB-BONELT-HDMIN' [ 1.829357] bone-capemgr bone_capemgr.9: Skipping loading of disabled cape with part# BB-BONE-EMMC-2G [ 1.839047] bone-capemgr bone_capemgr.9: Skipping loading of disabled cape with part# BB-BONELT-HDMI [ 1.848827] bone-capemgr bone_capemgr.9: initialized OK. [ 1.854450] bone-capemgr bone_capemgr.9: loader: before slot-6 BB-BONELT-HDMIN:00A0 (prio 2) [ 1.863302] bone-capemgr bone_capemgr.9: loader: check slot-6 BB-BONELT-HDMIN:00A0 (prio 2) [ 1.874166] OneNAND driver initializing [ 1.879831] usbcore: registered new interface driver cdc_ether [ 1.886076] usbcore: registered new interface driver rndis_host [ 1.892388] bone-capemgr bone_capemgr.9: loader: after slot-6 BB-BONELT-HDMIN:00A0 (prio 2) [ 1.901294] usbcore: registered new interface driver cdc_ncm [ 1.907286] bone-capemgr bone_capemgr.9: slot #6: Requesting firmware 'cape-boneblack-hdmin-00A0.dtbo' for board-name 'Bone-Black-HDMIN', version '00A0' [ 1.922528] usbcore: registered new interface driver cdc_acm [ 1.928486] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 1.936871] Initializing USB Mass Storage driver... [ 1.942049] bone-capemgr bone_capemgr.9: slot #6: dtbo 'cape-boneblack-hdmin-00A0.dtbo' loaded; converting to live tree [ 1.953494] usbcore: registered new interface driver usb-storage [ 1.959812] USB Mass Storage support registered. [ 1.965025] bone-capemgr bone_capemgr.9: slot #6: #2 overlays [ 1.973526] platform 4830e000.fb: alias fck already exists [ 1.979568] musb-hdrc: version 6.0, ?dma?, otg (peripheral+host) [ 1.986183] bone-capemgr bone_capemgr.9: slot #6: Applied #2 overlays. [ 1.993057] bone-capemgr bone_capemgr.9: loader: done slot-6 BB-BONELT-HDMIN:00A0 (prio 2) [ 2.002154] musb-hdrc musb-hdrc.0.auto: pdev->id = 0 [ 2.007414] musb-hdrc musb-hdrc.0.auto: drivers/usb/musb/musb_dsps.c:468 dsps_musb_init: OK [ 2.016562] musb-hdrc musb-hdrc.0.auto: *** mode=3 [ 2.021668] musb-hdrc musb-hdrc.0.auto: *** power=250 [ 2.027922] musb-hdrc musb-hdrc.1.auto: pdev->id = 1 [ 2.033176] musb-hdrc musb-hdrc.1.auto: drivers/usb/musb/musb_dsps.c:468 dsps_musb_init: OK [ 2.042173] musb-hdrc musb-hdrc.1.auto: *** mode=1 [ 2.047266] musb-hdrc musb-hdrc.1.auto: *** power=250 [ 2.052601] musb-hdrc musb-hdrc.1.auto: MUSB HDRC host driver [ 2.059191] musb-hdrc musb-hdrc.1.auto: new USB bus registered, assigned bus number 1 [ 2.067693] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 2.074849] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.082432] usb usb1: Product: MUSB HDRC host driver [ 2.087656] usb usb1: Manufacturer: Linux 3.8.13xenomai-bone28 musb-hcd [ 2.094597] usb usb1: SerialNumber: musb-hdrc.1.auto [ 2.101053] hub 1-0:1.0: USB hub found [ 2.105108] hub 1-0:1.0: 1 port detected [ 2.110822] mousedev: PS/2 mouse device common for all mice [ 2.119221] omap_rtc 44e3e000.rtc: rtc core: registered 44e3e000.rtc as rtc0 [ 2.126775] 44e3e000.rtc: already running [ 2.131310] i2c /dev entries driver [ 2.136849] pps_ldisc: PPS line discipline registered [ 2.142360] Driver for 1-wire Dallas network protocol. [ 2.149910] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec [ 2.157940] device-mapper: ioctl: 4.23.1-ioctl (2012-12-18) initialised: dm-devel@redhat.com [ 2.167428] omap_hsmmc mmc.5: of_parse_phandle_with_args of 'reset' failed [ 2.174703] omap_hsmmc mmc.5: Failed to get rstctl; not using any [ 2.181599] edma-dma-engine edma-dma-engine.0: allocated channel for 0:25 [ 2.188845] edma-dma-engine edma-dma-engine.0: allocated channel for 0:24 [ 2.196240] mmc.5 supply vmmc_aux not found, using dummy regulator [ 2.203741] omap_hsmmc mmc.5: pins are not configured from the driver [ 2.237572] pinctrl-single 44e10800.pinmux: pin 44e10854 already requested by 44e10800.pinmux; cannot claim for gpio-leds.8 [ 2.249322] pinctrl-single 44e10800.pinmux: pin-21 (gpio-leds.8) status -22 [ 2.256636] pinctrl-single 44e10800.pinmux: could not request pin 21 on device pinctrl-single [ 2.265638] leds-gpio gpio-leds.8: pins are not configured from the driver [ 2.274500] ledtrig-cpu: registered to indicate activity on CPUs [ 2.281405] edma-dma-engine edma-dma-engine.0: allocated channel for 0:36 [ 2.288703] omap-sham 53100000.sham: hw accel on OMAP rev 4.3 [ 2.297725] omap-aes 53500000.aes: OMAP AES hw accel rev: 3.2 [ 2.304091] edma-dma-engine edma-dma-engine.0: allocated channel for 0:5 [ 2.311381] edma-dma-engine edma-dma-engine.0: allocated channel for 0:6 [ 2.319913] usbcore: registered new interface driver usbhid [ 2.325844] usbhid: USB HID core driver [ 2.331473] ashmem: initialized [ 2.335441] logger: created 256K log 'log_main' [ 2.341294] logger: created 256K log 'log_events' [ 2.346806] logger: created 256K log 'log_radio' [ 2.352159] logger: created 256K log 'log_system' [ 2.361376] TCP: cubic registered [ 2.365183] NET: Registered protocol family 10 [ 2.371421] NET: Registered protocol family 17 [ 2.376226] mmc0: host does not support reading read-only switch. assuming write-enable. [ 2.385109] Key type dns_resolver registered [ 2.390125] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 [ 2.398382] ThumbEE CPU extension supported. [ 2.403024] Registering SWP/SWPB emulation handler [ 2.408272] mmc0: new high speed SDHC card at address 59b4 [ 2.415157] registered taskstats version 1 [ 2.420386] mmcblk0: mmc0:59b4 00000 7.47 GiB [ 2.427789] tilcdc 4830e000.fb: No power control GPIO [ 2.435259] mmcblk0: p1 p2 [ 2.549442] usb 1-1: new high-speed USB device number 2 using musb-hdrc [ 2.560661] tilcdc 4830e000.fb: found TDA19988 [ 2.566230] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010). [ 2.573197] [drm] No driver support for vblank timestamp query. [ 2.579578] [drm] forcing HDMI-A-1 connector ON [ 2.675804] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608 [ 2.675816] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 2.675827] usb 1-1: Product: USB2.0 Hub [ 2.677180] hub 1-1:1.0: USB hub found [ 2.677523] hub 1-1:1.0: 4 ports detected [ 2.686277] tilcdc 4830e000.fb: Not sure which CEA mode to set, leaving as DVI [ 2.700205] Console: switching to colour frame buffer device 100x30 [ 2.745831] tilcdc 4830e000.fb: fb0: frame buffer device [ 2.751512] tilcdc 4830e000.fb: registered panic notifier [ 2.757219] [drm] Initialized tilcdc 1.0.0 20121205 on minor 0 [ 2.813067] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6 [ 2.819481] davinci_mdio 4a101000.mdio: detected phy mask fffffffe [ 2.837558] libphy: 4a101000.mdio: probed [ 2.841896] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720 [ 2.851808] Detected MACID = c8:a0:30:b0:71:f9 [ 2.856535] cpsw 4a100000.ethernet: NAPI disabled [ 2.863960] omap_rtc 44e3e000.rtc: setting system clock to 2013-11-13 07:16:17 UTC (1384326977) [ 2.880506] ALSA device list: [ 2.883753] No soundcards found. [ 2.889338] Freeing init memory: 324K Loading, please wait... [ 2.959985] usb 1-1.1: new low-speed USB device number 3 using musb-hdrc [ 3.038948] udevd[96]: starting version 175 [ 3.063375] usb 1-1.1: New USB device found, idVendor=046d, idProduct=c31d [ 3.070653] usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 3.078322] usb 1-1.1: Product: USB Keyboard [ 3.082821] usb 1-1.1: Manufacturer: Logitech [ 3.108707] input: Logitech USB Keyboard as /devices/ocp.3/47400000.usb/musb-hdrc.1.auto/usb1/1-1/1-1.1/1-1.1:1.0/input/input1 [ 3.135521] hid-generic 0003:046D:C31D.0001: input,hidraw0: USB HID v1.10 Keyboard [Logitech USB Keyboard] on usb-musb-hdrc.1.auto-1.1/input0 [ 3.176163] input: Logitech USB Keyboard as /devices/ocp.3/47400000.usb/musb-hdrc.1.auto/usb1/1-1/1-1.1/1-1.1:1.1/input/input2 [ 3.202856] hid-generic 0003:046D:C31D.0002: input,hidraw1: USB HID v1.10 Device [Logitech USB Keyboard] on usb-musb-hdrc.1.auto-1.1/input1 [ 3.303760] usb 1-1.2: new full-speed USB device number 4 using musb-hdrc [ 3.402993] usb 1-1.2: New USB device found, idVendor=0eef, idProduct=0001 [ 3.410235] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 3.417912] usb 1-1.2: Product: USB TouchController [ 3.423048] usb 1-1.2: Manufacturer: eGalax Inc. modprobe: chdir(3.8.13xenomai-bone28): No such file or directory Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... modprobe: chdir(3.8.13xenomai-bone28): No such file or directory done. modprobe: chdir(3.8.13xenomai-bone28): No such file or directory [ 5.723745] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) Begin: Running /scripts/local-bottom ... done. done. Begin: Running /scripts/init-bottom ... done. INIT: version 2.88 booting [info] Using makefile-style concurrent boot in runlevel S. [....] Starting the hotplug events dispatcher: udevd[ 7.725439] udevd[340]: starting version 175 . ok udevd[340]: unknown key 'BUS' in /lib/udev/rules.d/99-touchscreen.rules:2 udevd[340]: invalid rule '/lib/udev/rules.d/99-touchscreen.rules:2' [....] Synthesizing the initial hotplug events...udevd[340]: unknown key 'BUS' in /lib/udev/rules.d/99-touchscreen.rules:2 udevd[340]: invalid rule '/lib/udev/rules.d/99-touchscreen.rules:2' done. [....] Waiting for /dev to be fully populated...[ 9.844920] input: eGalax Inc. USB TouchController as /devices/ocp.3/47400000.usb/musb-hdrc.1.auto/usb1/1-1/1-1.2/1-1.2:1.0/input/input3 [ 9.981390] usbcore: registered new interface driver usbtouchscreen done. [ ok ] Setting preliminary keymap...done. [ ok ] Setting parameters of disc: (none). [ ok ] Activating swap...done. [ 14.391855] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null) [....] Checking root file system...fsck from util-linux 2.20.1 rootfs: clean, 252313/485760 files, 1483713/1943040 blocks done. [ 14.772464] EXT4-fs (mmcblk0p2): re-mounted. Opts: errors=remount-ro [info] Loading kernel module evdev. [info] Loading kernel module hid-multitouch. [ ok ] Cleaning up temporary files... /tmp. [ ok ] Activating lvm and md swap...done. [....] Checking file systems...fsck from util-linux 2.20.1 done. [ ok ] Mounting local filesystems...done. [ ok ] Activating swapfile swap...done. [ ok ] Cleaning up temporary files.... [ ok ] Setting kernel variables ...done. [ ok ] Configuring network interfaces...done. [ ok ] Starting rpcbind daemon.... [....] Starting NFS common utilities: statd[ 24.398040] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ ok pd. [ ok ] Cleaning up temporary files.... [ ok ] Setting up ALSA...done. [info] Setting console screen modes. setterm: cannot (un)set powersave mode: Inappropriate ioctl for device [info] Skipping font and keymap setup (handled by console-setup). [ ok ] Setting up console font and keymap...done. [ ok ] Setting up X socket directories... /tmp/.X11-unix /tmp/.ICE-unix. INIT: Entering runlevel: 2 [info] Using makefile-style concurrent boot in runlevel 2. Not starting X display manager (xdm); it is not the default display manager. [ 28.170435] gadget: using random self ethernet address [ 28.198877] usb0: MAC 42:af:52:34:ff:ee [ 28.203077] usb0: HOST MAC c8:a0:30:b0:71:fb [ 28.243959] gadget: Mass Storage Function, version: 2009/09/11 [ 28.250304] gadget: Number of LUNs=1 [ 28.289845] lun0: LUN: removable file: /dev/mmcblk0p1 [ 28.326570] gadget: Multifunction Composite Gadget [ 28.369890] gadget: g_multi ready [ 28.393308] musb-hdrc musb-hdrc.0.auto: MUSB HDRC host driver [ 28.438596] musb-hdrc musb-hdrc.0.auto: new USB bus registered, assigned bus number 2 [ 28.478653] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 28.485883] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 28.493476] usb usb2: Product: MUSB HDRC host driver [ 28.498702] usb usb2: Manufacturer: Linux 3.8.13xenomai-bone28 musb-hcd [ 28.505647] usb usb2: SerialNumber: musb-hdrc.0.auto [ 28.540316] hub 2-0:1.0: USB hub found [ 28.575017] hub 2-0:1.0: 1 port detected [ ok ] Starting rpcbind daemon...[....] Already running.. [ ok ] Starting NFS common utilities: statd idmapd. [ ok ] Starting enhanced syslogd: rsyslogd. [ ok ] Starting deferred execution scheduler: atd. [ ok ] Starting periodic command scheduler: cron. [....] Starting system message bus: dbus[ 30.895947] IPv6: ADDRCONF(NETDEV_UP): usb0: link is not ready . ok [ ok ] Starting Light Display Manager: lightdm. [....] Starting MTA:[ 32.475336] tilcdc 4830e000.fb: timeout waiting for framedone [ ok 4. [ ok ] Loading cpufreq kernel modules...done (none). [ ok ] CPUFreq Utilities: Setting ondemand CPUFreq governor...disabled, governor not available...done. Starting printer spooler: lpd. [ ok ] Starting network connection manager: NetworkManager. [ 38.217543] net eth0: initializing cpsw version 1.12 (0) [ 38.241504] net eth0: phy found : id is : 0x7c0f1 [ 38.264445] libphy: PHY 4a101000.mdio:01 not found [ 38.269598] net eth0: phy 4a101000.mdio:01 not found on slave 1 [ 38.306416] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready saned disabled; edit /etc/default/saned [ ok ] Starting OpenBSD Secure Shell server: sshd. Starting very small Busybox based DHCP server: /usr/sbin/udhcpd already running. udhcpd. Debian GNU/Linux 7 arm ttyO0 arm login: [ 41.317571] libphy: 4a101000.mdio:00 - Link is Up - 100/Full [ 41.325500] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready Debian GNU/Linux 7 arm ttyO0 arm login: root Password: Last login: Fri Nov 1 17:05:20 UTC 2013 on tty4 Linux arm 3.8.13xenomai-bone28 #5 SMP Fri Nov 1 19:11:02 CET 2013 armv7l The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. root@arm:~# dmesg [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 3.8.13xenomai-bone28 (alexander@thinkpad.site) (gcc version 4.7.3 20130328 (prerelease) (crosstool-NG linaro-1.13.1-4.7-2013.04-20130415 - Linaro GCC 2013.04) ) #5 SMP Fri Nov 1 19:11:02 CET 2013 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: Generic AM33XX (Flattened Device Tree), model: TI AM335x BeagleBone [ 0.000000] bootconsole [earlycon0] enabled [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] On node 0 totalpages: 118016 [ 0.000000] free_area_init_node: node 0, pgdat c0a5b300, node_mem_map c0b3d000 [ 0.000000] Normal zone: 924 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 117092 pages, LIFO batch:31 [ 0.000000] AM335X ES1.0 (neon ) [ 0.000000] PERCPU: Embedded 11 pages/cpu @c0eed000 s23552 r8192 d13312 u45056 [ 0.000000] pcpu-alloc: s23552 r8192 d13312 u45056 alloc=11*4096 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 117092 [ 0.000000] Kernel command line: console=ttyO0,115200n8 capemgr.disable_partno=BB-BONELT-HDMI,BB-BONE-EMMC-2G video=HDMI-A-1:800x480M@85e root=/dev/mmcblk0p2 ro rootfstype=ext4 rootwait fixrtc mem=462M ip= earlyprintk=serial vram=50M [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] __ex_table already sorted, skipping sort [ 0.000000] allocated 946176 bytes of page_cgroup [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups [ 0.000000] Memory: 461MB = 461MB total [ 0.000000] Memory: 452464k/452464k available, 20624k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xdd000000 - 0xff000000 ( 544 MB) [ 0.000000] lowmem : 0xc0000000 - 0xdce00000 ( 462 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc0986b74 (9723 kB) [ 0.000000] .init : 0xc0987000 - 0xc09d8c00 ( 327 kB) [ 0.000000] .data : 0xc09da000 - 0xc0a5e2c0 ( 529 kB) [ 0.000000] .bss : 0xc0a5e2c0 - 0xc0b3c380 ( 889 kB) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts [ 0.000000] Total of 128 interrupts on 1 active controller [ 0.000000] OMAP clockevent source: GPTIMER1 at 24000000 Hz [ 0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms [ 0.000000] I-pipe, 24.000 MHz clocksource [ 0.000000] OMAP clocksource: GPTIMER2 at 24000000 Hz [ 0.000000] Interrupt pipeline (release #3) [ 0.000000] Console: colour dummy device 80x30 [ 0.019992] Calibrating delay loop... 363.67 BogoMIPS (lpj=354304) [ 0.045709] pid_max: default: 32768 minimum: 301 [ 0.050860] Security Framework initialized [ 0.055290] Mount-cache hash table entries: 512 [ 0.070938] Initializing cgroup subsys cpuacct [ 0.075666] Initializing cgroup subsys memory [ 0.080327] Initializing cgroup subsys blkio [ 0.084987] CPU: Testing write buffer coherency: ok [ 0.090758] CPU0: thread -1, cpu 0, socket -1, mpidr 0 [ 0.096255] Setting up static identity map for 0x8069e048 - 0x8069e0a0 [ 0.104847] Brought up 1 CPUs [ 0.108050] SMP: Total of 1 processors activated (363.67 BogoMIPS). [ 0.116483] devtmpfs: initialized [ 0.185611] pinctrl core: initialized pinctrl subsystem [ 0.191385] rstctl core: initialized rstctl subsystem [ 0.197282] regulator-dummy: no parameters [ 0.202136] NET: Registered protocol family 16 [ 0.207966] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.225736] pinctrl-single 44e10800.pinmux: 142 pins at pa f9e10800 size 568 [ 0.234162] platform 49000000.edma: alias fck already exists [ 0.240139] platform 49000000.edma: alias fck already exists [ 0.246092] platform 49000000.edma: alias fck already exists [ 0.253209] gpiochip_add: registered GPIOs 0 to 31 on device: gpio [ 0.253401] OMAP GPIO hardware version 0.1 [ 0.259234] gpiochip_add: registered GPIOs 32 to 63 on device: gpio [ 0.260640] gpiochip_add: registered GPIOs 64 to 95 on device: gpio [ 0.262220] gpiochip_add: registered GPIOs 96 to 127 on device: gpio [ 0.262786] of_get_named_gpio_flags exited with status 52 [ 0.262818] gpio-rctrl rstctl.4: loaded OK [ 0.272779] hw-breakpoint: debug architecture 0x4 unsupported. [ 0.281126] cpsw.0: No hwaddr in dt. Using c8:a0:30:b0:71:f9 from efuse [ 0.288096] cpsw.1: No hwaddr in dt. Using c8:a0:30:b0:71:fb from efuse [ 0.311701] bio: create slab at 0 [ 0.328423] edma-dma-engine edma-dma-engine.0: TI EDMA DMA engine driver [ 0.335670] of_get_named_gpio_flags: can't parse gpios property [ 0.335965] vmmcsd_fixed: 3300 mV [ 0.342572] SCSI subsystem initialized [ 0.347002] usbcore: registered new interface driver usbfs [ 0.352885] usbcore: registered new interface driver hub [ 0.358789] usbcore: registered new device driver usb [ 0.366362] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz [ 0.373986] input: tps65217_pwr_but as /devices/ocp.3/44e0b000.i2c/i2c-0/0-0024/input/input0 [ 0.384856] DCDC1: at 1500 mV [ 0.389506] vdd_mpu: 925 <--> 1325 mV at 1100 mV [ 0.395717] vdd_core: 925 <--> 1150 mV at 1100 mV [ 0.401981] LDO1: at 1800 mV [ 0.406350] LDO2: at 3300 mV [ 0.411622] LDO3: 1800 mV [ 0.415713] LDO4: at 3300 mV [ 0.419949] tps65217 0-0024: TPS65217 ID 0xe version 1.2 [ 0.426405] omap_i2c 44e0b000.i2c: unable to select pin group [ 0.433329] omap_i2c 4819c000.i2c: bus 1 rev0.11 at 100 kHz [ 0.442058] omap_i2c 4819c000.i2c: unable to select pin group [ 0.448384] media: Linux media interface: v0.10 [ 0.453432] Linux video capture interface: v2.00 [ 0.458526] pps_core: LinuxPPS API ver. 1 registered [ 0.463776] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.474096] Advanced Linux Sound Architecture Driver Initialized. [ 0.481573] NetLabel: Initializing [ 0.485217] NetLabel: domain hash size = 128 [ 0.489819] NetLabel: protocols = UNLABELED CIPSOv4 [ 0.495196] NetLabel: unlabeled traffic allowed by default [ 0.501597] Switching to clocksource ipipe_tsc [ 0.564354] NET: Registered protocol family 2 [ 0.570137] TCP established hash table entries: 4096 (order: 3, 32768 bytes) [ 0.577686] TCP bind hash table entries: 4096 (order: 4, 81920 bytes) [ 0.584617] TCP: Hash tables configured (established 4096 bind 4096) [ 0.591372] TCP: reno registered [ 0.594836] UDP hash table entries: 256 (order: 1, 12288 bytes) [ 0.601087] UDP-Lite hash table entries: 256 (order: 1, 12288 bytes) [ 0.608234] NET: Registered protocol family 1 [ 0.613519] RPC: Registered named UNIX socket transport module. [ 0.619774] RPC: Registered udp transport module. [ 0.624754] RPC: Registered tcp transport module. [ 0.629716] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.636932] Trying to unpack rootfs image as initramfs... [ 1.002236] Freeing initrd memory: 2904K [ 1.007125] hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5 counters available [ 1.016033] CPU PMU: attempt to register multiple PMU devices! [ 1.021942] arm-pmu: probe of arm-pmu failed with error -28 [ 1.028556] omap2_mbox_probe: platform not supported [ 1.320985] I-pipe: head domain Xenomai registered. [ 1.326198] Xenomai: hal/arm started. [ 1.332024] Xenomai: scheduling class idle registered. [ 1.337568] Xenomai: scheduling class rt registered. [ 1.350979] Xenomai: real-time nucleus v2.6.3 (Lies and Truths) loaded. [ 1.357953] Xenomai: debug mode enabled. [ 1.362700] Xenomai: starting native API services. [ 1.367792] Xenomai: starting POSIX services. [ 1.372602] Xenomai: starting RTDM services. [ 1.378638] VFS: Disk quotas dquot_6.5.2 [ 1.383143] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 1.391488] NFS: Registering the id_resolver key type [ 1.397037] Key type id_resolver registered [ 1.401487] Key type id_legacy registered [ 1.405818] fuse init (API version 7.20) [ 1.410944] Btrfs loaded [ 1.413886] msgmni has been set to 889 [ 1.421165] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) [ 1.428942] io scheduler noop registered [ 1.433114] io scheduler deadline registered [ 1.437763] io scheduler cfq registered (default) [ 1.444770] tps65217-bl tps65217-bl: no platform data provided [ 1.450973] tps65217-bl: probe of tps65217-bl failed with error -22 [ 1.458473] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 1.467583] omap_uart 44e09000.serial: did not get pins for uart0 error: -19 [ 1.475414] 44e09000.serial: ttyO0 at MMIO 0x44e09000 (irq = 88) is a OMAP UART0 [ 1.483357] console [ttyO0] enabled, bootconsole disabled [ 1.495878] [drm] Initialized drm 1.1.0 20060810 [ 1.515249] brd: module loaded [ 1.526338] loop: module loaded [ 1.529877] at24 0-0050: 32768 byte 24c256 EEPROM, writable, 1 bytes/write [ 1.537174] at24 1-0054: 32768 byte 24c256 EEPROM, writable, 1 bytes/write [ 1.544468] at24 1-0055: 32768 byte 24c256 EEPROM, writable, 1 bytes/write [ 1.551754] at24 1-0056: 32768 byte 24c256 EEPROM, writable, 1 bytes/write [ 1.559039] at24 1-0057: 32768 byte 24c256 EEPROM, writable, 1 bytes/write [ 1.573455] bone-capemgr bone_capemgr.9: Baseboard: 'A335BNLT,0A5A,1613BBBK1042' [ 1.581308] bone-capemgr bone_capemgr.9: compatible-baseboard=ti,beaglebone-black [ 1.589221] bone-capemgr bone_capemgr.9: Skipping disabled cape with part# BB-BONE-EMMC-2G [ 1.597921] bone-capemgr bone_capemgr.9: Skipping disabled cape with part# BB-BONELT-HDMI [ 1.637281] bone-capemgr bone_capemgr.9: slot #0: No cape found [ 1.674385] bone-capemgr bone_capemgr.9: slot #1: No cape found [ 1.711493] bone-capemgr bone_capemgr.9: slot #2: No cape found [ 1.748600] bone-capemgr bone_capemgr.9: slot #3: No cape found [ 1.754860] bone-capemgr bone_capemgr.9: slot #4: specific override [ 1.761463] bone-capemgr bone_capemgr.9: bone: Using override eeprom data at slot 4 [ 1.769504] bone-capemgr bone_capemgr.9: slot #4: 'Bone-LT-eMMC-2G,00A0,Texas Instrument,BB-BONE-EMMC-2G' [ 1.779650] bone-capemgr bone_capemgr.9: slot #5: specific override [ 1.786251] bone-capemgr bone_capemgr.9: bone: Using override eeprom data at slot 5 [ 1.794285] bone-capemgr bone_capemgr.9: slot #5: 'Bone-Black-HDMI,00A0,Texas Instrument,BB-BONELT-HDMI' [ 1.804335] bone-capemgr bone_capemgr.9: slot #6: specific override [ 1.810937] bone-capemgr bone_capemgr.9: bone: Using override eeprom data at slot 6 [ 1.818979] bone-capemgr bone_capemgr.9: slot #6: 'Bone-Black-HDMIN,00A0,Texas Instrument,BB-BONELT-HDMIN' [ 1.829357] bone-capemgr bone_capemgr.9: Skipping loading of disabled cape with part# BB-BONE-EMMC-2G [ 1.839047] bone-capemgr bone_capemgr.9: Skipping loading of disabled cape with part# BB-BONELT-HDMI [ 1.848827] bone-capemgr bone_capemgr.9: initialized OK. [ 1.854450] bone-capemgr bone_capemgr.9: loader: before slot-6 BB-BONELT-HDMIN:00A0 (prio 2) [ 1.863302] bone-capemgr bone_capemgr.9: loader: check slot-6 BB-BONELT-HDMIN:00A0 (prio 2) [ 1.874166] OneNAND driver initializing [ 1.879831] usbcore: registered new interface driver cdc_ether [ 1.886076] usbcore: registered new interface driver rndis_host [ 1.892388] bone-capemgr bone_capemgr.9: loader: after slot-6 BB-BONELT-HDMIN:00A0 (prio 2) [ 1.901294] usbcore: registered new interface driver cdc_ncm [ 1.907286] bone-capemgr bone_capemgr.9: slot #6: Requesting firmware 'cape-boneblack-hdmin-00A0.dtbo' for board-name 'Bone-Black-HDMIN', version '00A0' [ 1.922528] usbcore: registered new interface driver cdc_acm [ 1.928486] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 1.936871] Initializing USB Mass Storage driver... [ 1.942049] bone-capemgr bone_capemgr.9: slot #6: dtbo 'cape-boneblack-hdmin-00A0.dtbo' loaded; converting to live tree [ 1.953494] usbcore: registered new interface driver usb-storage [ 1.959812] USB Mass Storage support registered. [ 1.965025] bone-capemgr bone_capemgr.9: slot #6: #2 overlays [ 1.973526] platform 4830e000.fb: alias fck already exists [ 1.979568] musb-hdrc: version 6.0, ?dma?, otg (peripheral+host) [ 1.986183] bone-capemgr bone_capemgr.9: slot #6: Applied #2 overlays. [ 1.993057] bone-capemgr bone_capemgr.9: loader: done slot-6 BB-BONELT-HDMIN:00A0 (prio 2) [ 2.002154] musb-hdrc musb-hdrc.0.auto: pdev->id = 0 [ 2.007414] musb-hdrc musb-hdrc.0.auto: drivers/usb/musb/musb_dsps.c:468 dsps_musb_init: OK [ 2.016343] musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn) [ 2.016367] musb-hdrc: MHDRC RTL version 2.0 [ 2.016382] musb-hdrc: setup fifo_mode 4 [ 2.016409] musb-hdrc: 28/31 max ep, 16384/16384 memory [ 2.016562] musb-hdrc musb-hdrc.0.auto: *** mode=3 [ 2.021668] musb-hdrc musb-hdrc.0.auto: *** power=250 [ 2.027922] musb-hdrc musb-hdrc.1.auto: pdev->id = 1 [ 2.033176] musb-hdrc musb-hdrc.1.auto: drivers/usb/musb/musb_dsps.c:468 dsps_musb_init: OK [ 2.041978] musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn) [ 2.041998] musb-hdrc: MHDRC RTL version 2.0 [ 2.042012] musb-hdrc: setup fifo_mode 4 [ 2.042034] musb-hdrc: 28/31 max ep, 16384/16384 memory [ 2.042173] musb-hdrc musb-hdrc.1.auto: *** mode=1 [ 2.047266] musb-hdrc musb-hdrc.1.auto: *** power=250 [ 2.052601] musb-hdrc musb-hdrc.1.auto: MUSB HDRC host driver [ 2.059191] musb-hdrc musb-hdrc.1.auto: new USB bus registered, assigned bus number 1 [ 2.067480] musb-hdrc musb-hdrc.1.auto: supports USB remote wakeup [ 2.067606] usb usb1: default language 0x0409 [ 2.067670] usb usb1: udev 1, busnum 1, minor = 0 [ 2.067693] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 2.074849] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.082432] usb usb1: Product: MUSB HDRC host driver [ 2.087656] usb usb1: Manufacturer: Linux 3.8.13xenomai-bone28 musb-hcd [ 2.094597] usb usb1: SerialNumber: musb-hdrc.1.auto [ 2.100688] usb usb1: usb_probe_device [ 2.100717] usb usb1: configuration #1 chosen from 1 choice [ 2.100794] usb usb1: adding 1-0:1.0 (config #1, interface 0) [ 2.101000] hub 1-0:1.0: usb_probe_interface [ 2.101021] hub 1-0:1.0: usb_probe_interface - got id [ 2.101053] hub 1-0:1.0: USB hub found [ 2.105108] hub 1-0:1.0: 1 port detected [ 2.109270] hub 1-0:1.0: standalone hub [ 2.109290] hub 1-0:1.0: individual port power switching [ 2.109307] hub 1-0:1.0: no over-current protection [ 2.109324] hub 1-0:1.0: Single TT [ 2.109344] hub 1-0:1.0: TT requires at most 8 FS bit times (666 ns) [ 2.109362] hub 1-0:1.0: power on to power good time: 10ms [ 2.109409] hub 1-0:1.0: local power source is good [ 2.109542] hub 1-0:1.0: enabling power on all ports [ 2.110822] mousedev: PS/2 mouse device common for all mice [ 2.119221] omap_rtc 44e3e000.rtc: rtc core: registered 44e3e000.rtc as rtc0 [ 2.126775] 44e3e000.rtc: already running [ 2.131310] i2c /dev entries driver [ 2.136849] pps_ldisc: PPS line discipline registered [ 2.142360] Driver for 1-wire Dallas network protocol. [ 2.149910] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec [ 2.157940] device-mapper: ioctl: 4.23.1-ioctl (2012-12-18) initialised: dm-devel@redhat.com [ 2.167353] of_get_named_gpio_flags exited with status 6 [ 2.167374] of_get_named_gpio_flags: can't parse gpios property [ 2.167390] of_get_named_gpio_flags: can't parse gpios property [ 2.167428] omap_hsmmc mmc.5: of_parse_phandle_with_args of 'reset' failed [ 2.174703] omap_hsmmc mmc.5: Failed to get rstctl; not using any [ 2.181599] edma-dma-engine edma-dma-engine.0: allocated channel for 0:25 [ 2.188845] edma-dma-engine edma-dma-engine.0: allocated channel for 0:24 [ 2.196240] mmc.5 supply vmmc_aux not found, using dummy regulator [ 2.203741] omap_hsmmc mmc.5: pins are not configured from the driver [ 2.210667] hub 1-0:1.0: state 7 ports 1 chg 0000 evt 0000 [ 2.210754] hub 1-0:1.0: hub_suspend [ 2.210798] usb usb1: bus auto-suspend, wakeup 1 [ 2.237572] pinctrl-single 44e10800.pinmux: pin 44e10854 already requested by 44e10800.pinmux; cannot claim for gpio-leds.8 [ 2.249322] pinctrl-single 44e10800.pinmux: pin-21 (gpio-leds.8) status -22 [ 2.256636] pinctrl-single 44e10800.pinmux: could not request pin 21 on device pinctrl-single [ 2.265638] leds-gpio gpio-leds.8: pins are not configured from the driver [ 2.272898] of_get_named_gpio_flags exited with status 53 [ 2.272924] of_get_named_gpio_flags exited with status 54 [ 2.272945] of_get_named_gpio_flags exited with status 55 [ 2.272965] of_get_named_gpio_flags exited with status 56 [ 2.273006] of_get_named_gpio_flags exited with status 53 [ 2.273354] of_get_named_gpio_flags exited with status 54 [ 2.273597] of_get_named_gpio_flags exited with status 55 [ 2.273799] of_get_named_gpio_flags exited with status 56 [ 2.274500] ledtrig-cpu: registered to indicate activity on CPUs [ 2.281405] edma-dma-engine edma-dma-engine.0: allocated channel for 0:36 [ 2.288703] omap-sham 53100000.sham: hw accel on OMAP rev 4.3 [ 2.297725] omap-aes 53500000.aes: OMAP AES hw accel rev: 3.2 [ 2.304091] edma-dma-engine edma-dma-engine.0: allocated channel for 0:5 [ 2.311381] edma-dma-engine edma-dma-engine.0: allocated channel for 0:6 [ 2.319913] usbcore: registered new interface driver usbhid [ 2.325844] usbhid: USB HID core driver [ 2.331473] ashmem: initialized [ 2.335441] logger: created 256K log 'log_main' [ 2.340420] usb usb1: usb wakeup-resume [ 2.340476] usb usb1: usb auto-resume [ 2.340506] hub 1-0:1.0: hub_resume [ 2.340567] hub 1-0:1.0: port 1: status 0101 change 0001 [ 2.341294] logger: created 256K log 'log_events' [ 2.346806] logger: created 256K log 'log_radio' [ 2.352159] logger: created 256K log 'log_system' [ 2.361376] TCP: cubic registered [ 2.365183] NET: Registered protocol family 10 [ 2.371421] NET: Registered protocol family 17 [ 2.376226] mmc0: host does not support reading read-only switch. assuming write-enable. [ 2.385109] Key type dns_resolver registered [ 2.390125] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 [ 2.398382] ThumbEE CPU extension supported. [ 2.403024] Registering SWP/SWPB emulation handler [ 2.408272] mmc0: new high speed SDHC card at address 59b4 [ 2.415157] registered taskstats version 1 [ 2.420386] mmcblk0: mmc0:59b4 00000 7.47 GiB [ 2.427755] of_get_named_gpio_flags: can't parse gpios property [ 2.427789] tilcdc 4830e000.fb: No power control GPIO [ 2.435259] mmcblk0: p1 p2 [ 2.444191] hub 1-0:1.0: state 7 ports 1 chg 0002 evt 0000 [ 2.444279] hub 1-0:1.0: port 1, status 0101, change 0000, 12 Mb/s [ 2.549442] usb 1-1: new high-speed USB device number 2 using musb-hdrc [ 2.560661] tilcdc 4830e000.fb: found TDA19988 [ 2.566230] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010). [ 2.573197] [drm] No driver support for vblank timestamp query. [ 2.579578] [drm] forcing HDMI-A-1 connector ON [ 2.675459] usb 1-1: default language 0x0409 [ 2.675788] usb 1-1: udev 2, busnum 1, minor = 1 [ 2.675804] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608 [ 2.675816] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 2.675827] usb 1-1: Product: USB2.0 Hub [ 2.676550] usb 1-1: usb_probe_device [ 2.676567] usb 1-1: configuration #1 chosen from 1 choice [ 2.676924] usb 1-1: adding 1-1:1.0 (config #1, interface 0) [ 2.677143] hub 1-1:1.0: usb_probe_interface [ 2.677155] hub 1-1:1.0: usb_probe_interface - got id [ 2.677180] hub 1-1:1.0: USB hub found [ 2.677523] hub 1-1:1.0: 4 ports detected [ 2.677535] hub 1-1:1.0: standalone hub [ 2.677544] hub 1-1:1.0: ganged power switching [ 2.677554] hub 1-1:1.0: global over-current protection [ 2.677563] hub 1-1:1.0: Single TT [ 2.677576] hub 1-1:1.0: TT requires at most 32 FS bit times (2664 ns) [ 2.677586] hub 1-1:1.0: Port indicators are supported [ 2.677596] hub 1-1:1.0: power on to power good time: 100ms [ 2.677990] hub 1-1:1.0: local power source is good [ 2.678001] hub 1-1:1.0: no over-current condition exists [ 2.678436] hub 1-1:1.0: enabling power on all ports [ 2.680009] hub 1-0:1.0: state 7 ports 1 chg 0000 evt 0002 [ 2.680052] hub 1-0:1.0: port 1 enable change, status 00000503 [ 2.686277] tilcdc 4830e000.fb: Not sure which CEA mode to set, leaving as DVI [ 2.700205] Console: switching to colour frame buffer device 100x30 [ 2.745831] tilcdc 4830e000.fb: fb0: frame buffer device [ 2.751512] tilcdc 4830e000.fb: registered panic notifier [ 2.757219] [drm] Initialized tilcdc 1.0.0 20121205 on minor 0 [ 2.780302] hub 1-1:1.0: port 1: status 0301 change 0001 [ 2.780890] hub 1-1:1.0: port 2: status 0101 change 0001 [ 2.813067] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6 [ 2.819481] davinci_mdio 4a101000.mdio: detected phy mask fffffffe [ 2.837558] libphy: 4a101000.mdio: probed [ 2.841896] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720 [ 2.851808] Detected MACID = c8:a0:30:b0:71:f9 [ 2.856535] cpsw 4a100000.ethernet: NAPI disabled [ 2.863960] omap_rtc 44e3e000.rtc: setting system clock to 2013-11-13 07:16:17 UTC (1384326977) [ 2.880506] ALSA device list: [ 2.883753] No soundcards found. [ 2.887541] hub 1-1:1.0: state 7 ports 4 chg 0006 evt 0000 [ 2.887938] hub 1-1:1.0: port 1, status 0301, change 0000, 1.5 Mb/s [ 2.889338] Freeing init memory: 324K [ 2.959985] usb 1-1.1: new low-speed USB device number 3 using musb-hdrc [ 3.038948] udevd[96]: starting version 175 [ 3.060778] usb 1-1.1: skipped 1 descriptor after interface [ 3.060822] usb 1-1.1: skipped 1 descriptor after interface [ 3.061363] usb 1-1.1: default language 0x0409 [ 3.063343] usb 1-1.1: udev 3, busnum 1, minor = 2 [ 3.063375] usb 1-1.1: New USB device found, idVendor=046d, idProduct=c31d [ 3.070653] usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 3.078322] usb 1-1.1: Product: USB Keyboard [ 3.082821] usb 1-1.1: Manufacturer: Logitech [ 3.100322] usb 1-1.1: usb_probe_device [ 3.100362] usb 1-1.1: configuration #1 chosen from 1 choice [ 3.101920] usb 1-1.1: adding 1-1.1:1.0 (config #1, interface 0) [ 3.103940] usbhid 1-1.1:1.0: usb_probe_interface [ 3.103972] usbhid 1-1.1:1.0: usb_probe_interface - got id [ 3.108707] input: Logitech USB Keyboard as /devices/ocp.3/47400000.usb/musb-hdrc.1.auto/usb1/1-1/1-1.1/1-1.1:1.0/input/input1 [ 3.135521] hid-generic 0003:046D:C31D.0001: input,hidraw0: USB HID v1.10 Keyboard [Logitech USB Keyboard] on usb-musb-hdrc.1.auto-1.1/input0 [ 3.165029] usb 1-1.1: adding 1-1.1:1.1 (config #1, interface 1) [ 3.166727] usbhid 1-1.1:1.1: usb_probe_interface [ 3.166762] usbhid 1-1.1:1.1: usb_probe_interface - got id [ 3.176163] input: Logitech USB Keyboard as /devices/ocp.3/47400000.usb/musb-hdrc.1.auto/usb1/1-1/1-1.1/1-1.1:1.1/input/input2 [ 3.202856] hid-generic 0003:046D:C31D.0002: input,hidraw1: USB HID v1.10 Device [Logitech USB Keyboard] on usb-musb-hdrc.1.auto-1.1/input1 [ 3.235123] hub 1-1:1.0: port 2, status 0101, change 0000, 12 Mb/s [ 3.303760] usb 1-1.2: new full-speed USB device number 4 using musb-hdrc [ 3.401966] usb 1-1.2: skipped 1 descriptor after interface [ 3.402215] usb 1-1.2: default language 0x0409 [ 3.402963] usb 1-1.2: udev 4, busnum 1, minor = 3 [ 3.402993] usb 1-1.2: New USB device found, idVendor=0eef, idProduct=0001 [ 3.410235] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 3.417912] usb 1-1.2: Product: USB TouchController [ 3.423048] usb 1-1.2: Manufacturer: eGalax Inc. [ 3.472165] usb 1-1.2: usb_probe_device [ 3.472209] usb 1-1.2: configuration #1 chosen from 1 choice [ 3.475355] usb 1-1.2: adding 1-1.2:1.0 (config #1, interface 0) [ 3.475764] usbhid 1-1.2:1.0: usb_probe_interface [ 3.475792] usbhid 1-1.2:1.0: usb_probe_interface - got id [ 5.723745] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) [ 7.725439] udevd[340]: starting version 175 [ 9.839700] usbtouchscreen 1-1.2:1.0: usb_probe_interface [ 9.839839] usbtouchscreen 1-1.2:1.0: usb_probe_interface - got id [ 9.844920] input: eGalax Inc. USB TouchController as /devices/ocp.3/47400000.usb/musb-hdrc.1.auto/usb1/1-1/1-1.2/1-1.2:1.0/input/input3 [ 9.981390] usbcore: registered new interface driver usbtouchscreen [ 14.391855] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null) [ 14.772464] EXT4-fs (mmcblk0p2): re-mounted. Opts: errors=remount-ro [ 24.398040] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 28.170435] gadget: using random self ethernet address [ 28.198877] usb0: MAC 42:af:52:34:ff:ee [ 28.203077] usb0: HOST MAC c8:a0:30:b0:71:fb [ 28.243959] gadget: Mass Storage Function, version: 2009/09/11 [ 28.250304] gadget: Number of LUNs=1 [ 28.289845] lun0: LUN: removable file: /dev/mmcblk0p1 [ 28.326570] gadget: Multifunction Composite Gadget [ 28.369890] gadget: g_multi ready [ 28.393308] musb-hdrc musb-hdrc.0.auto: MUSB HDRC host driver [ 28.438596] musb-hdrc musb-hdrc.0.auto: new USB bus registered, assigned bus number 2 [ 28.478410] musb-hdrc musb-hdrc.0.auto: supports USB remote wakeup [ 28.478560] usb usb2: default language 0x0409 [ 28.478628] usb usb2: udev 1, busnum 2, minor = 128 [ 28.478653] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 28.485883] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 28.493476] usb usb2: Product: MUSB HDRC host driver [ 28.498702] usb usb2: Manufacturer: Linux 3.8.13xenomai-bone28 musb-hcd [ 28.505647] usb usb2: SerialNumber: musb-hdrc.0.auto [ 28.539774] usb usb2: usb_probe_device [ 28.539817] usb usb2: configuration #1 chosen from 1 choice [ 28.539921] usb usb2: adding 2-0:1.0 (config #1, interface 0) [ 28.540250] hub 2-0:1.0: usb_probe_interface [ 28.540277] hub 2-0:1.0: usb_probe_interface - got id [ 28.540316] hub 2-0:1.0: USB hub found [ 28.575017] hub 2-0:1.0: 1 port detected [ 28.604262] hub 2-0:1.0: standalone hub [ 28.604300] hub 2-0:1.0: individual port power switching [ 28.604320] hub 2-0:1.0: no over-current protection [ 28.604338] hub 2-0:1.0: Single TT [ 28.604359] hub 2-0:1.0: TT requires at most 8 FS bit times (666 ns) [ 28.604378] hub 2-0:1.0: power on to power good time: 10ms [ 28.604453] hub 2-0:1.0: local power source is good [ 28.604621] hub 2-0:1.0: enabling power on all ports [ 28.705931] hub 2-0:1.0: state 7 ports 1 chg 0000 evt 0000 [ 28.706037] hub 2-0:1.0: hub_suspend [ 28.706083] usb usb2: bus auto-suspend, wakeup 1 [ 30.895947] IPv6: ADDRCONF(NETDEV_UP): usb0: link is not ready [ 32.475336] tilcdc 4830e000.fb: timeout waiting for framedone [ 38.217543] net eth0: initializing cpsw version 1.12 (0) [ 38.241504] net eth0: phy found : id is : 0x7c0f1 [ 38.264445] libphy: PHY 4a101000.mdio:01 not found [ 38.269598] net eth0: phy 4a101000.mdio:01 not found on slave 1 [ 38.306416] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 41.317571] libphy: 4a101000.mdio:00 - Link is Up - 100/Full [ 41.325500] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready