U-Boot SPL 2013.04-rc1-14237-g90639fe-dirty (Apr 13 2013 - 13:57:11) musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Peripheral mode controller at 47401000 using PIO, IRQ 0 musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Host mode controller at 47401800 using PIO, IRQ 0 OMAP SD/MMC: 0 mmc_send_cmd : timeout: No status update reading u-boot.img reading u-boot.img U-Boot 2013.04-rc1-14237-g90639fe-dirty (Apr 13 2013 - 13:57:11) I2C: ready DRAM: 512 MiB WARNING: Caches not enabled NAND: No NAND device found!!! 0 MiB MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 *** Warning - readenv() failed, using default environment musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Peripheral mode controller at 47401000 using PIO, IRQ 0 musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Host mode controller at 47401800 using PIO, IRQ 0 Net: not set. Validating first E-fuse MAC cpsw, usb_ether Hit any key to stop autoboot: 0 gpio: pin 53 (gpio 53) value is 1 mmc0 is current device micro SD card found mmc0 is current device gpio: pin 54 (gpio 54) value is 1 SD/MMC found on device 0 reading uEnv.txt 1891 bytes read in 5 ms (369.1 KiB/s) Loaded environment from uEnv.txt Importing environment from mmc ... Running uenvcmd ... reading zImage 3344504 bytes read in 385 ms (8.3 MiB/s) reading uInitrd 2975910 bytes read in 343 ms (8.3 MiB/s) reading /dtbs/am335x-boneblack.dtb 24808 bytes read in 11 ms (2.2 MiB/s) ## Loading init Ramdisk from Legacy Image at 81000000 ... Image Name: initramfs Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 2975846 Bytes = 2.8 MiB Load Address: 00000000 Entry Point: 00000000 ## Flattened Device Tree blob at 815f0000 Booting using the fdt blob at 0x815f0000 Using Device Tree in place at 815f0000, end 815f90e7 Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 3.8.13-bone28 (alexander@thinkpad.site) (gcc version 4.7.3 20130328 (prerelease) (crosstool-NG linaro-1.13.1-4.7-2013.04-20130415 - Linaro GCC 2013.04) ) #1 SMP Wed Oct 23 21:43:09 CEST 2013 [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine: Generic AM33XX (Flattened Device Tree), model: TI AM335x BeagleBone [ 0.000000] bootconsole [earlycon0] enabled [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] AM335X ES1.0 (neon ) [ 0.000000] PERCPU: Embedded 9 pages/cpu @c0c45000 s14080 r8192 d14592 u36864 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 64768 [ 0.000000] Kernel command line: console=ttyO0,115200n8 capemgr.disable_partno=BB-BONELT-HDMI,BB-BONE-EMMC-2G video=HDMI-A-1:800x480M@85e root=/dev/mmcblk0p2 ro rootfstype=ext4 rootwait fixrtc mem=256M ip=dhcp earlyprintk=serial vram=50M [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] __ex_table already sorted, skipping sort [ 0.000000] allocated 524288 bytes of page_cgroup [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups [ 0.000000] Memory: 255MB = 255MB total [ 0.000000] Memory: 244856k/244856k available, 17288k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xd0800000 - 0xff000000 ( 744 MB) [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc08f1a00 (9127 kB) [ 0.000000] .init : 0xc08f2000 - 0xc093b700 ( 294 kB) [ 0.000000] .data : 0xc093c000 - 0xc09bf500 ( 526 kB) [ 0.000000] .bss : 0xc09bf500 - 0xc0a36900 ( 477 kB) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts [ 0.000000] Total of 128 interrupts on 1 active controller [ 0.000000] OMAP clockevent source: GPTIMER1 at 24000000 Hz [ 0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms [ 0.000000] OMAP clocksource: GPTIMER2 at 24000000 Hz [ 0.000000] Console: colour dummy device 80x30 [ 0.010436] Calibrating delay loop... 363.67 BogoMIPS (lpj=354304) [ 0.035947] pid_max: default: 32768 minimum: 301 [ 0.041059] Security Framework initialized [ 0.045482] Mount-cache hash table entries: 512 [ 0.060067] Initializing cgroup subsys cpuacct [ 0.064806] Initializing cgroup subsys memory [ 0.069466] Initializing cgroup subsys blkio [ 0.074113] CPU: Testing write buffer coherency: ok [ 0.079824] CPU0: thread -1, cpu 0, socket -1, mpidr 0 [ 0.085323] Setting up static identity map for 0x8061f130 - 0x8061f188 [ 0.093821] Brought up 1 CPUs [ 0.097005] SMP: Total of 1 processors activated (363.67 BogoMIPS). [ 0.104872] devtmpfs: initialized [ 0.173059] pinctrl core: initialized pinctrl subsystem [ 0.178812] rstctl core: initialized rstctl subsystem [ 0.184654] regulator-dummy: no parameters [ 0.189605] NET: Registered protocol family 16 [ 0.195383] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.212750] pinctrl-single 44e10800.pinmux: 142 pins at pa f9e10800 size 568 [ 0.220965] platform 49000000.edma: alias fck already exists [ 0.226931] platform 49000000.edma: alias fck already exists [ 0.232881] platform 49000000.edma: alias fck already exists [ 0.240134] OMAP GPIO hardware version 0.1 [ 0.249368] gpio-rctrl rstctl.3: loaded OK [ 0.259118] hw-breakpoint: debug architecture 0x4 unsupported. [ 0.267412] cpsw.0: No hwaddr in dt. Using c8:a0:30:b0:71:f9 from efuse [ 0.274392] cpsw.1: No hwaddr in dt. Using c8:a0:30:b0:71:fb from efuse [ 0.295862] bio: create slab at 0 [ 0.311864] edma-dma-engine edma-dma-engine.0: TI EDMA DMA engine driver [ 0.319357] vmmcsd_fixed: 3300 mV [ 0.325907] SCSI subsystem initialized [ 0.330370] usbcore: registered new interface driver usbfs [ 0.336244] usbcore: registered new interface driver hub [ 0.342131] usbcore: registered new device driver usb [ 0.349655] omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz [ 0.357036] input: tps65217_pwr_but as /devices/ocp.2/44e0b000.i2c/i2c-0/0-0024/input/input0 [ 0.367791] DCDC1: at 1500 mV [ 0.372341] vdd_mpu: 925 <--> 1325 mV at 950 mV [ 0.378373] vdd_core: 925 <--> 1150 mV at 1100 mV [ 0.384557] LDO1: at 1800 mV [ 0.388842] LDO2: at 3300 mV [ 0.393983] LDO3: 1800 mV [ 0.398018] LDO4: at 3300 mV [ 0.402206] tps65217 0-0024: TPS65217 ID 0xe version 1.2 [ 0.408668] omap_i2c 44e0b000.i2c: unable to select pin group [ 0.415584] omap_i2c 4819c000.i2c: bus 1 rev0.11 at 100 kHz [ 0.424184] omap_i2c 4819c000.i2c: unable to select pin group [ 0.430506] media: Linux media interface: v0.10 [ 0.435614] Linux video capture interface: v2.00 [ 0.440656] pps_core: LinuxPPS API ver. 1 registered [ 0.445909] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.456163] Advanced Linux Sound Architecture Driver Initialized. [ 0.463611] NetLabel: Initializing [ 0.467253] NetLabel: domain hash size = 128 [ 0.471847] NetLabel: protocols = UNLABELED CIPSOv4 [ 0.477171] NetLabel: unlabeled traffic allowed by default [ 0.483518] Switching to clocksource gp_timer [ 0.544325] NET: Registered protocol family 2 [ 0.550067] TCP established hash table entries: 2048 (order: 2, 16384 bytes) [ 0.557565] TCP bind hash table entries: 2048 (order: 3, 40960 bytes) [ 0.564420] TCP: Hash tables configured (established 2048 bind 2048) [ 0.571170] TCP: reno registered [ 0.574634] UDP hash table entries: 256 (order: 1, 12288 bytes) [ 0.580881] UDP-Lite hash table entries: 256 (order: 1, 12288 bytes) [ 0.588016] NET: Registered protocol family 1 [ 0.593246] RPC: Registered named UNIX socket transport module. [ 0.599528] RPC: Registered udp transport module. [ 0.604508] RPC: Registered tcp transport module. [ 0.609469] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.616650] Trying to unpack rootfs image as initramfs... [ 0.973338] Freeing initrd memory: 2904K [ 0.978601] CPU PMU: probing PMU on CPU 0 [ 0.982891] hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5 counters available [ 0.991900] omap2_mbox_probe: platform not supported [ 1.271680] VFS: Disk quotas dquot_6.5.2 [ 1.276147] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 1.284320] NFS: Registering the id_resolver key type [ 1.289828] Key type id_resolver registered [ 1.294279] Key type id_legacy registered [ 1.298600] fuse init (API version 7.20) [ 1.303621] Btrfs loaded [ 1.306606] msgmni has been set to 483 [ 1.313600] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) [ 1.321381] io scheduler noop registered [ 1.325546] io scheduler deadline registered [ 1.330176] io scheduler cfq registered (default) [ 1.337167] tps65217-bl tps65217-bl: no platform data provided [ 1.343365] tps65217-bl: probe of tps65217-bl failed with error -22 [ 1.350831] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 1.359839] omap_uart 44e09000.serial: did not get pins for uart0 error: -19 [ 1.367578] 44e09000.serial: ttyO0 at MMIO 0x44e09000 (irq = 88) is a OMAP UART0 [ 1.375505] console [ttyO0] enabled, bootconsole disabled [ 1.375505] console [ttyO0] enabled, bootconsole disabled [ 1.388047] [drm] Initialized drm 1.1.0 20060810 [ 1.406642] brd: module loaded [ 1.416955] loop: module loaded [ 1.420435] at24 0-0050: 32768 byte 24c256 EEPROM, writable, 1 bytes/write [ 1.427741] at24 1-0054: 32768 byte 24c256 EEPROM, writable, 1 bytes/write [ 1.435028] at24 1-0055: 32768 byte 24c256 EEPROM, writable, 1 bytes/write [ 1.442312] at24 1-0056: 32768 byte 24c256 EEPROM, writable, 1 bytes/write [ 1.449594] at24 1-0057: 32768 byte 24c256 EEPROM, writable, 1 bytes/write [ 1.464100] bone-capemgr bone_capemgr.8: Baseboard: 'A335BNLT,0A5A,1613BBBK1042' [ 1.471944] bone-capemgr bone_capemgr.8: compatible-baseboard=ti,beaglebone-black [ 1.479841] bone-capemgr bone_capemgr.8: Skipping disabled cape with part# BB-BONE-EMMC-2G [ 1.488540] bone-capemgr bone_capemgr.8: Skipping disabled cape with part# BB-BONELT-HDMI [ 1.527299] bone-capemgr bone_capemgr.8: slot #0: No cape found [ 1.564404] bone-capemgr bone_capemgr.8: slot #1: No cape found [ 1.601511] bone-capemgr bone_capemgr.8: slot #2: No cape found [ 1.638622] bone-capemgr bone_capemgr.8: slot #3: No cape found [ 1.644886] bone-capemgr bone_capemgr.8: slot #4: specific override [ 1.651490] bone-capemgr bone_capemgr.8: bone: Using override eeprom data at slot 4 [ 1.659530] bone-capemgr bone_capemgr.8: slot #4: 'Bone-LT-eMMC-2G,00A0,Texas Instrument,BB-BONE-EMMC-2G' [ 1.669679] bone-capemgr bone_capemgr.8: slot #5: specific override [ 1.676283] bone-capemgr bone_capemgr.8: bone: Using override eeprom data at slot 5 [ 1.684321] bone-capemgr bone_capemgr.8: slot #5: 'Bone-Black-HDMI,00A0,Texas Instrument,BB-BONELT-HDMI' [ 1.694380] bone-capemgr bone_capemgr.8: slot #6: specific override [ 1.700983] bone-capemgr bone_capemgr.8: bone: Using override eeprom data at slot 6 [ 1.709023] bone-capemgr bone_capemgr.8: slot #6: 'Bone-Black-HDMIN,00A0,Texas Instrument,BB-BONELT-HDMIN' [ 1.719391] bone-capemgr bone_capemgr.8: Skipping loading of disabled cape with part# BB-BONE-EMMC-2G [ 1.729074] bone-capemgr bone_capemgr.8: Skipping loading of disabled cape with part# BB-BONELT-HDMI [ 1.738850] bone-capemgr bone_capemgr.8: initialized OK. [ 1.744471] bone-capemgr bone_capemgr.8: loader: before slot-6 BB-BONELT-HDMIN:00A0 (prio 2) [ 1.753326] bone-capemgr bone_capemgr.8: loader: check slot-6 BB-BONELT-HDMIN:00A0 (prio 2) [ 1.764149] OneNAND driver initializing [ 1.769788] usbcore: registered new interface driver cdc_ether [ 1.776026] usbcore: registered new interface driver rndis_host [ 1.782334] bone-capemgr bone_capemgr.8: loader: after slot-6 BB-BONELT-HDMIN:00A0 (prio 2) [ 1.791221] usbcore: registered new interface driver cdc_ncm [ 1.797209] bone-capemgr bone_capemgr.8: slot #6: Requesting firmware 'cape-boneblack-hdmin-00A0.dtbo' for board-name 'Bone-Black-HDMIN', version '00A0' [ 1.812335] usbcore: registered new interface driver cdc_acm [ 1.818316] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 1.826706] Initializing USB Mass Storage driver... [ 1.831877] bone-capemgr bone_capemgr.8: slot #6: dtbo 'cape-boneblack-hdmin-00A0.dtbo' loaded; converting to live tree [ 1.843338] usbcore: registered new interface driver usb-storage [ 1.849654] USB Mass Storage support registered. [ 1.854853] bone-capemgr bone_capemgr.8: slot #6: #2 overlays [ 1.863152] platform 4830e000.fb: alias fck already exists [ 1.869237] musb-hdrc: version 6.0, ?dma?, otg (peripheral+host) [ 1.875847] bone-capemgr bone_capemgr.8: slot #6: Applied #2 overlays. [ 1.882742] bone-capemgr bone_capemgr.8: loader: done slot-6 BB-BONELT-HDMIN:00A0 (prio 2) [ 1.891785] musb-hdrc musb-hdrc.0.auto: pdev->id = 0 [ 1.897038] musb-hdrc musb-hdrc.0.auto: drivers/usb/musb/musb_dsps.c:468 dsps_musb_init: OK [ 1.906327] musb-hdrc musb-hdrc.0.auto: *** mode=3 [ 1.911408] musb-hdrc musb-hdrc.0.auto: *** power=250 [ 1.917502] musb-hdrc musb-hdrc.1.auto: pdev->id = 1 [ 1.922807] musb-hdrc musb-hdrc.1.auto: drivers/usb/musb/musb_dsps.c:468 dsps_musb_init: OK [ 1.931831] musb-hdrc musb-hdrc.1.auto: *** mode=1 [ 1.936904] musb-hdrc musb-hdrc.1.auto: *** power=250 [ 1.942221] musb-hdrc musb-hdrc.1.auto: MUSB HDRC host driver [ 1.948685] musb-hdrc musb-hdrc.1.auto: new USB bus registered, assigned bus number 1 [ 1.957200] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.964340] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.971918] usb usb1: Product: MUSB HDRC host driver [ 1.977139] usb usb1: Manufacturer: Linux 3.8.13-bone28 musb-hcd [ 1.983445] usb usb1: SerialNumber: musb-hdrc.1.auto [ 1.989815] hub 1-0:1.0: USB hub found [ 1.993892] hub 1-0:1.0: 1 port detected [ 1.999405] mousedev: PS/2 mouse device common for all mice [ 2.007937] omap_rtc 44e3e000.rtc: rtc core: registered 44e3e000.rtc as rtc0 [ 2.015444] 44e3e000.rtc: already running [ 2.019952] i2c /dev entries driver [ 2.025396] pps_ldisc: PPS line discipline registered [ 2.030864] Driver for 1-wire Dallas network protocol. [ 2.038194] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec [ 2.046177] device-mapper: ioctl: 4.23.1-ioctl (2012-12-18) initialised: dm-devel@redhat.com [ 2.055162] cpuidle: using governor ladder [ 2.059524] cpuidle: using governor menu [ 2.064178] omap_hsmmc mmc.4: of_parse_phandle_with_args of 'reset' failed [ 2.071417] omap_hsmmc mmc.4: Failed to get rstctl; not using any [ 2.078307] edma-dma-engine edma-dma-engine.0: allocated channel for 0:25 [ 2.085526] edma-dma-engine edma-dma-engine.0: allocated channel for 0:24 [ 2.092912] mmc.4 supply vmmc_aux not found, using dummy regulator [ 2.100362] omap_hsmmc mmc.4: pins are not configured from the driver [ 2.135369] pinctrl-single 44e10800.pinmux: pin 44e10854 already requested by 44e10800.pinmux; cannot claim for gpio-leds.7 [ 2.147119] pinctrl-single 44e10800.pinmux: pin-21 (gpio-leds.7) status -22 [ 2.154427] pinctrl-single 44e10800.pinmux: could not request pin 21 on device pinctrl-single [ 2.163422] leds-gpio gpio-leds.7: pins are not configured from the driver [ 2.172094] ledtrig-cpu: registered to indicate activity on CPUs [ 2.178932] edma-dma-engine edma-dma-engine.0: allocated channel for 0:36 [ 2.186214] omap-sham 53100000.sham: hw accel on OMAP rev 4.3 [ 2.194921] omap-aes 53500000.aes: OMAP AES hw accel rev: 3.2 [ 2.201703] edma-dma-engine edma-dma-engine.0: allocated channel for 0:5 [ 2.209016] edma-dma-engine edma-dma-engine.0: allocated channel for 0:6 [ 2.217392] usbcore: registered new interface driver usbhid [ 2.223326] usbhid: USB HID core driver [ 2.229348] ashmem: initialized [ 2.233288] logger: created 256K log 'log_main' [ 2.238612] logger: created 256K log 'log_events' [ 2.243970] logger: created 256K log 'log_radio' [ 2.249199] logger: created 256K log 'log_system' [ 2.258117] TCP: cubic registered [ 2.261850] NET: Registered protocol family 10 [ 2.268094] NET: Registered protocol family 17 [ 2.272875] mmc0: host does not support reading read-only switch. assuming write-enable. [ 2.281753] Key type dns_resolver registered [ 2.286738] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 [ 2.294972] ThumbEE CPU extension supported. [ 2.299558] mmc0: new high speed SDHC card at address 59b4 [ 2.305358] Registering SWP/SWPB emulation handler [ 2.311486] registered taskstats version 1 [ 2.316752] mmcblk0: mmc0:59b4 00000 7.47 GiB [ 2.323985] tilcdc 4830e000.fb: No power control GPIO [ 2.332306] mmcblk0: p1 p2 [ 2.435552] usb 1-1: new high-speed USB device number 2 using musb-hdrc [ 2.456263] tilcdc 4830e000.fb: found TDA19988 [ 2.461779] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010). [ 2.468738] [drm] No driver support for vblank timestamp query. [ 2.475115] [drm] forcing HDMI-A-1 connector ON [ 2.561943] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608 [ 2.561956] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 2.561967] usb 1-1: Product: USB2.0 Hub [ 2.563418] hub 1-1:1.0: USB hub found [ 2.563730] hub 1-1:1.0: 4 ports detected [ 2.589833] tilcdc 4830e000.fb: Not sure which CEA mode to set, leaving as DVI [ 2.603758] Console: switching to colour frame buffer device 100x30 [ 2.649318] tilcdc 4830e000.fb: fb0: frame buffer device [ 2.654992] tilcdc 4830e000.fb: registered panic notifier [ 2.660688] [drm] Initialized tilcdc 1.0.0 20121205 on minor 0 [ 2.716803] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6 [ 2.723234] davinci_mdio 4a101000.mdio: detected phy mask fffffffe [ 2.740413] libphy: 4a101000.mdio: probed [ 2.744697] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720 [ 2.754604] Detected MACID = c8:a0:30:b0:71:f9 [ 2.759319] cpsw 4a100000.ethernet: NAPI disabled [ 2.766456] omap_rtc 44e3e000.rtc: setting system clock to 2013-10-24 16:21:57 UTC (1382631717) [ 2.830017] tilcdc 4830e000.fb: timeout waiting for framedone [ 2.841929] usb 1-1.1: new low-speed USB device number 3 using musb-hdrc [ 2.854094] net eth0: initializing cpsw version 1.12 (0) [ 2.861919] net eth0: phy found : id is : 0x7c0f1 [ 2.866900] libphy: PHY 4a101000.mdio:01 not found [ 2.872034] net eth0: phy 4a101000.mdio:01 not found on slave 1 [ 2.884246] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 2.952533] usb 1-1.1: New USB device found, idVendor=046d, idProduct=c31d [ 2.959758] usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 2.967420] usb 1-1.1: Product: USB Keyboard [ 2.971902] usb 1-1.1: Manufacturer: Logitech [ 2.983255] input: Logitech USB Keyboard as /devices/ocp.2/47400000.usb/musb-hdrc.1.auto/usb1/1-1/1-1.1/1-1.1:1.0/input/input1 [ 2.995609] hid-generic 0003:046D:C31D.0001: input: USB HID v1.10 Keyboard [Logitech USB Keyboard] on usb-musb-hdrc.1.auto-1.1/input0 [ 3.017037] input: Logitech USB Keyboard as /devices/ocp.2/47400000.usb/musb-hdrc.1.auto/usb1/1-1/1-1.1/1-1.1:1.1/input/input2 [ 3.029316] hid-generic 0003:046D:C31D.0002: input: USB HID v1.10 Device [Logitech USB Keyboard] on usb-musb-hdrc.1.auto-1.1/input1 [ 3.107571] usb 1-1.2: new full-speed USB device number 4 using musb-hdrc [ 3.196544] usb 1-1.2: New USB device found, idVendor=0eef, idProduct=0001 [ 3.203791] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 3.211457] usb 1-1.2: Product: USB TouchController [ 3.216575] usb 1-1.2: Manufacturer: eGalax Inc. [ 5.939867] libphy: 4a101000.mdio:00 - Link is Up - 100/Full [ 5.945900] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 5.959077] Sending DHCP requests ., OK [ 6.973056] IP-Config: Got DHCP answer from 192.168.1.1, my address is 192.168.1.23 [ 6.981367] IP-Config: Complete: [ 6.984800] device=eth0, hwaddr=c8:a0:30:b0:71:f9, ipaddr=192.168.1.23, mask=255.255.255.0, gw=192.168.1.1 [ 6.995372] host=192.168.1.23, domain=, nis-domain=(none) [ 7.001488] bootserver=192.168.1.1, rootserver=192.168.1.1, rootpath= [ 7.008509] nameserver0=195.34.133.21, nameserver1=212.186.211.21 [ 7.015563] ALSA device list: [ 7.018677] No soundcards found. [ 7.023050] Freeing init memory: 292K Loading, please wait... [ 7.105850] udevd[96]: starting version 175 modprobe: chdir(3.8.13-bone28): No such file or directory Begin: Loading essential drivers ... done. Begin: Running /scripts/init-premount ... done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done. Begin: Running /scripts/local-premount ... modprobe: chdir(3.8.13-bone28): No such file or directory done. modprobe: chdir(3.8.13-bone28): No such file or directory [ 8.434087] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) Begin: Running /scripts/local-bottom ... done. done. Begin: Running /scripts/init-bottom ... done. INIT: version 2.88 booting [info] Using makefile-style concurrent boot in runlevel S. [....] Starting the hotplug events dispatcher: udevd[ 10.488678] udevd[316]: starting version 175 . ok udevd[316]: unknown key 'BUS' in /lib/udev/rules.d/99-touchscreen.rules:2 udevd[316]: invalid rule '/lib/udev/rules.d/99-touchscreen.rules:2' [....] Synthesizing the initial hotplug events...udevd[316]: unknown key 'BUS' in /lib/udev/rules.d/99-touchscreen.rules:2 udevd[316]: invalid rule '/lib/udev/rules.d/99-touchscreen.rules:2' done. [ ok ] Waiting for /dev to be fully populated...done. [ ok ] Setting preliminary keymap...done. [ ok ] Setting parameters of disc: (none). [ ok ] Activating swap...done. [ 14.523952] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null) [....] Checking root file system...fsck from util-linux 2.20.1 rootfs: clean, 235273/485760 files, 1348625/1943040 blocks done. [ 14.819948] EXT4-fs (mmcblk0p2): re-mounted. Opts: errors=remount-ro [info] Loading kernel module evdev. [info] Loading kernel module hid-multitouch. [ ok ] Cleaning up temporary files... /tmp. [ ok ] Activating lvm and md swap...done. [....] Checking file systems...fsck from util-linux 2.20.1 done. [ ok ] Mounting local filesystems...done. [ ok ] Activating swapfile swap...done. [ ok ] Cleaning up temporary files.... [ ok ] Setting kernel variables ...done. [....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.2.2 Copyright 2004-2011 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/eth0/c8:a0:30:b0:71:f9 Sending on LPF/eth0/c8:a0:30:b0:71:f9 Sending on Socket/fallback DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 8 DHCPREQUEST on eth0 to 255.255.255.255 port 67 DHCPOFFER from 192.168.1.1 DHCPACK from 192.168.1.1 RTNETLINK answers: File exists bound to 192.168.1.23 -- renewal in 241409 seconds. done. [ ok ] Starting rpcbind daemon.... [....] Starting NFS common utilities: statd[ 22.507667] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ ok pd. [ ok ] Cleaning up temporary files.... [ ok ] Setting up ALSA...done. [info] Setting console screen modes. setterm: cannot (un)set powersave mode: Inappropriate ioctl for device [info] Skipping font and keymap setup (handled by console-setup). [ ok ] Setting up console font and keymap...done. [ ok ] Setting up X socket directories... /tmp/.X11-unix /tmp/.ICE-unix. INIT: Entering runlevel: 2 [info] Using makefile-style concurrent boot in runlevel 2. Not starting X display manager (xdm); it is not the default display manager. [ 25.042639] gadget: using random self ethernet address [ 25.074889] usb0: MAC a6:c4:17:93:c7:a8 [ 25.079004] usb0: HOST MAC c8:a0:30:b0:71:fb [ 25.142644] gadget: Mass Storage Function, version: 2009/09/11 [ 25.148912] gadget: Number of LUNs=1 [ 25.203185] lun0: LUN: removable file: /dev/mmcblk0p1 [ 25.238411] gadget: Multifunction Composite Gadget [ 25.263429] gadget: g_multi ready [ 25.279403] musb-hdrc musb-hdrc.0.auto: MUSB HDRC host driver [ 25.308106] musb-hdrc musb-hdrc.0.auto: new USB bus registered, assigned bus number 2 [ 25.342040] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 25.349222] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 25.356800] usb usb2: Product: MUSB HDRC host driver [ 25.362036] usb usb2: Manufacturer: Linux 3.8.13-bone28 musb-hcd [ 25.368335] usb usb2: SerialNumber: musb-hdrc.0.auto [ ok ] Starting rpcbind daemon...[....] Already running.. [ 25.398952] hub 2-0:1.0: USB hub found [....] Starting NFS common utilities: statd idmapd[ 25.422813] hub 2-0:1.0: 1 port detected . ok [ ok ] Starting enhanced syslogd: rsyslogd. [ ok ] Starting deferred execution scheduler: atd. [ ok ] Starting periodic command scheduler: cron. [ ok ] Starting system message bus: dbus. [....] Starting MTA:[ 27.753337] IPv6: ADDRCONF(NETDEV_UP): usb0: link is not ready [ ok ] Starting Light Display Manager: lightdm. [ 29.398395] tilcdc 4830e000.fb: timeout waiting for framedone [ ok 4. [ ok ] Loading cpufreq kernel modules...done (none). [ ok ] CPUFreq Utilities: Setting ondemand CPUFreq governor...CPU0...done. Starting printer spooler: lpd. saned disabled; edit /etc/default/saned [ ok ] Starting OpenBSD Secure Shell server: sshd. Starting very small Busybox based DHCP server: /usr/sbin/udhcpd already running. udhcpd. /etc/rc.local: 15: /etc/rc.local: cannot create /sys/module/xeno_nucleus/parameters/xenomai_gid: Directory nonexistent [FAIL] startpar: service(s) returned failure: rc.local ... failed! Debian GNU/Linux 7 arm ttyO0 arm login: