U-Boot 2019.01 (Oct 06 2020 - 11:32:55 +0200) CPU : DRA752-GP ES2.0 Model: PHYTEC phyCORE-AM5716 with 1GiB DDR3 (1 bank), Commercial Temp Board: phyCORE-AM57x kit DRAM: 2 GiB MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 Loading Environment from FAT... *** Warning - bad CRC, using default environment Loading Environment from MMC... *** Warning - bad CRC, using default environment Warning: fastboot.board_rev: unknown board revision Net: Warning: ethernet@48484000 using MAC address from ROM eth0: ethernet@48484000 Hit any key to stop autoboot: 0 switch to partitions #0, OK mmc0 is current device SD/MMC found on device 0 ** Unable to read file boot.scr ** ** Unable to read file uEnv.txt ** switch to partitions #0, OK mmc0 is current device SD/MMC found on device 0 5755392 bytes read in 255 ms (21.5 MiB/s) 141925 bytes read in 9 ms (15 MiB/s) ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Loading Device Tree to 8ffda000, end 8ffffa64 ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.19.38 (ralph@ralph) (gcc version 7.4.0 (Buildroot 2019.02.11)) #3 SMP PREEMPT Wed Oct 7 09:42:47 CEST 2020 [ 0.000000] CPU: ARMv7 Processor [412fc0f2] revision 2 (ARMv7), cr=30c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: PHYTEC phyCORE-AM5728 with 2GiB (banks) DDR3, Industrial Temp [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] Reserved memory: created CMA memory pool at 0x0000000095000000, size 8 MiB [ 0.000000] OF: reserved mem: initialized node dsp2-memory@95000000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created CMA memory pool at 0x0000000095800000, size 32 MiB [ 0.000000] OF: reserved mem: initialized node ipu1-memory@95800000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created CMA memory pool at 0x0000000097800000, size 64 MiB [ 0.000000] OF: reserved mem: initialized node dsp1-memory@97800000, compatible id shared-dma-pool [ 0.000000] Reserved memory: created CMA memory pool at 0x000000009b800000, size 56 MiB [ 0.000000] OF: reserved mem: initialized node ipu2-memory@9b800000, compatible id shared-dma-pool [ 0.000000] cma: Reserved 24 MiB at 0x00000000fd400000 [ 0.000000] OMAP4: Map 0x00000000fed00000 to (ptrval) for dram barrier [ 0.000000] DRA752 ES2.0 [ 0.000000] random: get_random_bytes called from start_kernel+0xb4/0x470 with crng_init=0 [ 0.000000] percpu: Embedded 15 pages/cpu s32396 r8192 d20852 u61440 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 468544 [ 0.000000] Kernel command line: console=ttyS2,115200n8 root=PARTUUID=00000000-02 rw rootfstype=ext4 rootwait [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 1659444K/1881088K available (8192K kernel code, 324K rwdata, 2716K rodata, 2048K init, 269K bss, 33228K reserved, 188416K cma-reserved, 1266688) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (10208 kB) [ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (2048 kB) [ 0.000000] .data : 0x(ptrval) - 0x(ptrval) ( 325 kB) [ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 270 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] Tasks RCU enabled. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] OMAP clockevent source: timer1 at 32786 Hz [ 0.000000] arch_timer: cp15 timer(s) running at 6.14MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x16af5adb9, max_idle_ns: 440795202250 ns [ 0.000005] sched_clock: 56 bits at 6MHz, resolution 162ns, wraps every 4398046511023ns [ 0.000017] Switching to timer-based delay loop, resolution 162ns [ 0.000313] clocksource: 32k_counter: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 58327039986419 ns [ 0.000322] OMAP clocksource: 32k_counter at 32768 Hz [ 0.000813] Console: colour dummy device 80x30 [ 0.000856] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.29 BogoMIPS (lpj=61475) [ 0.000874] pid_max: default: 32768 minimum: 301 [ 0.000999] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.001013] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.001574] CPU: Testing write buffer coherency: ok [ 0.001612] CPU0: Spectre v2: using ICIALLU workaround [ 0.001822] /cpus/cpu@0 missing clock-frequency property [ 0.001842] /cpus/cpu@1 missing clock-frequency property [ 0.001854] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.059898] Setting up static identity map for 0x80200000 - 0x80200060 [ 0.079907] rcu: Hierarchical SRCU implementation. [ 0.100099] EFI services will not be available. [ 0.119967] smp: Bringing up secondary CPUs ... [ 0.200299] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.200305] CPU1: Spectre v2: using ICIALLU workaround [ 0.200425] smp: Brought up 1 node, 2 CPUs [ 0.200437] SMP: Total of 2 processors activated (24.59 BogoMIPS). [ 0.200445] CPU: All CPU(s) started in HYP mode. [ 0.200452] CPU: Virtualization extensions available. [ 0.201008] devtmpfs: initialized [ 0.220910] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.221162] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.221179] futex hash table entries: 512 (order: 3, 32768 bytes) [ 0.224608] pinctrl core: initialized pinctrl subsystem [ 0.225116] DMI not present or invalid. [ 0.225392] NET: Registered protocol family 16 [ 0.226513] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.227523] omap_hwmod: l3_main_2 using broken dt data from ocp [ 0.430313] cpuidle: using governor ladder [ 0.430365] cpuidle: using governor menu [ 0.440455] OMAP GPIO hardware version 0.1 [ 0.462599] No ATAGs? [ 0.462674] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.462688] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.463235] omap4_sram_init:Unable to allocate sram needed to handle errata I688 [ 0.463247] omap4_sram_init:Unable to get sram pool needed to handle errata I688 [ 0.463867] OMAP DMA hardware revision 0.0 [ 0.474225] edma 43300000.edma: memcpy is disabled [ 0.477525] edma 43300000.edma: TI EDMA DMA engine driver [ 0.484583] omap-dma-engine 4a056000.dma-controller: OMAP DMA engine driver (LinkedList1/2/3 supported) [ 0.488415] omap-iommu 40d01000.mmu: 40d01000.mmu registered [ 0.488596] omap-iommu 40d02000.mmu: 40d02000.mmu registered [ 0.488828] omap-iommu 58882000.mmu: 58882000.mmu registered [ 0.489061] omap-iommu 55082000.mmu: 55082000.mmu registered [ 0.489430] omap-iommu 41501000.mmu: 41501000.mmu registered [ 0.489601] omap-iommu 41502000.mmu: 41502000.mmu registered [ 0.489873] iommu: Adding device 58820000.ipu to group 1 [ 0.489954] iommu: Adding device 55020000.ipu to group 2 [ 0.490085] iommu: Adding device 40800000.dsp to group 0 [ 0.490310] iommu: Adding device 41000000.dsp to group 3 [ 0.491819] media: Linux media interface: v0.10 [ 0.491856] videodev: Linux video capture interface: v2.00 [ 0.491929] pps_core: LinuxPPS API ver. 1 registered [ 0.491938] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.491958] PTP clock support registered [ 0.491989] EDAC MC: Ver: 3.0.0 [ 0.492486] omap-mailbox: probe of 4883c000.mailbox failed with error -22 [ 0.492549] omap-mailbox: probe of 4883e000.mailbox failed with error -22 [ 0.492769] omap-mailbox 48840000.mailbox: omap mailbox rev 0x400 [ 0.493020] omap-mailbox 48842000.mailbox: omap mailbox rev 0x400 [ 0.493349] Advanced Linux Sound Architecture Driver Initialized. [ 0.494143] clocksource: Switched to clocksource arch_sys_counter [ 0.501793] missing cooling_device property [ 0.501807] failed to build thermal zone cpu_thermal: -2 [ 0.502315] NET: Registered protocol family 2 [ 0.502891] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes) [ 0.502920] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.502983] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.503109] TCP: Hash tables configured (established 8192 bind 8192) [ 0.503178] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.503212] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.503348] NET: Registered protocol family 1 [ 0.503700] RPC: Registered named UNIX socket transport module. [ 0.503710] RPC: Registered udp transport module. [ 0.503718] RPC: Registered tcp transport module. [ 0.503726] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.504724] hw perfevents: no interrupt-affinity property for /pmu, guessing. [ 0.504903] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available [ 0.505834] Initialise system trusted keyrings [ 0.505966] workingset: timestamp_bits=14 max_order=19 bucket_order=5 [ 0.510761] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.511223] NFS: Registering the id_resolver key type [ 0.511244] Key type id_resolver registered [ 0.511252] Key type id_legacy registered [ 0.511289] ntfs: driver 2.1.32 [Flags: R/W]. [ 0.511504] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc. [ 0.513315] Key type asymmetric registered [ 0.513327] Asymmetric key parser 'x509' registered [ 0.513373] bounce: pool size: 64 pages [ 0.513406] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) [ 0.513416] io scheduler noop registered [ 0.513425] io scheduler deadline registered [ 0.513520] io scheduler cfq registered (default) [ 0.513531] io scheduler mq-deadline registered [ 0.513540] io scheduler kyber registered [ 0.518582] pinctrl-single 4a003400.pinmux: 282 pins, size 1128 [ 0.567999] Serial: 8250/16550 driver, 10 ports, IRQ sharing enabled [ 0.571535] console [ttyS2] disabled [ 0.571585] 48020000.serial: ttyS2 at MMIO 0x48020000 (irq = 43, base_baud = 3000000) is a 8250 [ 1.470768] console [ttyS2] enabled [ 1.475283] 48066000.serial: ttyS4 at MMIO 0x48066000 (irq = 44, base_baud = 3000000) is a 8250 [ 1.498189] brd: module loaded [ 1.507364] loop: module loaded [ 1.514471] libphy: Fixed MDIO Bus: probed [ 1.574175] davinci_mdio 48485000.mdio: davinci mdio revision 1.6, bus freq 1000000 [ 1.581871] libphy: 48485000.mdio: probed [ 1.590653] davinci_mdio 48485000.mdio: phy[1]: device 48485000.mdio:01, driver Micrel KSZ9031 Gigabit PHY [ 1.600403] davinci_mdio 48485000.mdio: phy[2]: device 48485000.mdio:02, driver Micrel KSZ9031 Gigabit PHY [ 1.610648] cpsw 48484000.ethernet: Detected MACID = 7c:01:0a:1f:99:3e [ 1.617267] cpsw 48484000.ethernet: initialized cpsw ale version 1.4 [ 1.623652] cpsw 48484000.ethernet: ALE Table size 1024 [ 1.628978] cpsw 48484000.ethernet: cpts: overflow check period 500 (jiffies) [ 1.636978] cpsw 48484000.ethernet: cpsw: Detected MACID = 7c:01:0a:1f:99:3f [ 1.645272] i2c /dev entries driver [ 1.650921] ti-soc-thermal 4a0021e0.bandgap: thermal zone device is NULL [ 1.659263] sdhci: Secure Digital Host Controller Interface driver [ 1.665497] sdhci: Copyright(c) Pierre Ossman [ 1.670652] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.677791] sdhci-omap 480b4000.mmc: failed to set system capabilities [ 1.685654] ledtrig-cpu: registered to indicate activity on CPUs [ 1.696191] NET: Registered protocol family 10 [ 1.701615] Segment Routing with IPv6 [ 1.705397] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 1.711806] NET: Registered protocol family 17 [ 1.716481] Key type dns_resolver registered [ 1.720891] Registering SWP/SWPB emulation handler [ 1.725728] omap_voltage_late_init: Voltage driver support not added [ 1.732110] Power Management for TI OMAP4+ devices. [ 1.737711] Loading compiled-in X.509 certificates [ 1.766630] dmm 4e000000.dmm: workaround for errata i878 in use [ 1.774228] dmm 4e000000.dmm: initialized all PAT entries [ 1.783900] palmas 0-0058: Irq flag is 0x00000008 [ 1.816263] palmas 0-0058: Muxing GPIO 2f, PWM 0, LED 0 [ 1.823349] SMPS12: supplied by regulator-dummy [ 1.829971] SMPS3: supplied by vcc_3v3 [ 1.835783] SMPS45: supplied by regulator-dummy [ 1.842566] SMPS6: supplied by vcc_3v3 [ 1.846790] smps6: Bringing 1050000uV into 1030000-1030000uV [ 1.854691] SMPS7: supplied by regulator-dummy [ 1.860840] SMPS8: supplied by vcc_3v3 [ 1.866169] SMPS9: supplied by regulator-dummy [ 1.871427] LDO1: supplied by vcc_5v0 [ 1.875375] random: fast init done [ 1.880673] LDO2: supplied by vcc_5v0 [ 1.886319] LDO3: supplied by vcc_3v3 [ 1.891941] LDO4: supplied by vcc_3v3 [ 1.897611] LDO5: supplied by regulator-dummy [ 1.902809] LDO6: supplied by regulator-dummy [ 1.908028] LDO7: supplied by regulator-dummy [ 1.913223] LDO8: supplied by regulator-dummy [ 1.918430] LDO9: supplied by vcc_3v3 [ 1.924273] LDOLN: supplied by vcc_3v3 [ 1.930012] LDOUSB: supplied by vcc_5v0 [ 1.938740] at24 0-0050: 4096 byte 24c32 EEPROM, writable, 32 bytes/write [ 1.947095] rtc-m41t80 0-0068: Oscillator failure, data is invalid. [ 1.953551] rtc-m41t80 0-0068: registered as rtc2 [ 1.958727] omap_i2c 48070000.i2c: bus 0 rev0.12 at 400 kHz [ 1.965084] omap_i2c 48060000.i2c: bus 2 rev0.12 at 400 kHz [ 1.971356] omap_i2c 4807a000.i2c: bus 3 rev0.12 at 400 kHz [ 1.977457] ti-soc-thermal 4a0021e0.bandgap: thermal zone device is NULL [ 1.984659] cpu cpu0: Linked as a consumer to regulator.11 [ 1.990237] cpu cpu0: Linked as a consumer to regulator.6 [ 1.997093] omap_gpio 4805d000.gpio: Could not set line 27 debounce to 200000 microseconds (-22) [ 2.005946] sdhci-omap 4809c000.mmc: Got CD GPIO [ 2.010640] sdhci-omap 4809c000.mmc: Got WP GPIO [ 2.015432] sdhci-omap 4809c000.mmc: Linked as a consumer to regulator.5 [ 2.022229] sdhci-omap 4809c000.mmc: 4809c000.mmc supply vqmmc not found, using dummy regulator [ 2.031041] sdhci-omap 4809c000.mmc: Linked as a consumer to regulator.0 [ 2.037851] sdhci-omap 4809c000.mmc: Dropping the link to regulator.0 [ 2.044667] sdhci-omap 4809c000.mmc: Linked as a consumer to regulator.18 [ 2.051717] sdhci-omap 4809c000.mmc: no pinctrl state for ddr_3_3v mode [ 2.084409] mmc0: SDHCI controller on 4809c000.mmc [4809c000.mmc] using ADMA [ 2.092753] vdd_3v3: supplied by regen1 [ 2.096936] sdhci-omap 480b4000.mmc: Linked as a consumer to regulator.1 [ 2.103828] sdhci-omap 480b4000.mmc: Dropping the link to regulator.1 [ 2.110563] sdhci-omap 480b4000.mmc: Linked as a consumer to regulator.1 [ 2.141330] mmc1: SDHCI controller on 480b4000.mmc [480b4000.mmc] using ADMA [ 2.149583] ti-soc-thermal 4a0021e0.bandgap: thermal zone device is NULL [ 2.166955] ti-soc-thermal 4a0021e0.bandgap: thermal zone device is NULL [ 2.166977] mmc0: new high speed SDHC card at address 59b4 [ 2.179656] hctosys: unable to open rtc device (rtc0) [ 2.185333] aic_dvdd_fixed: supplied by vdd_3v3 [ 2.189926] vtt_fixed: supplied by smps3 [ 2.193841] mmcblk0: mmc0:59b4 USDU1 14.9 GiB [ 2.198519] aic_dvdd_fixed: disabling [ 2.202392] ldousb: disabling [ 2.205705] ALSA device list: [ 2.208682] No soundcards found. [ 2.209718] mmcblk0: p1 p2 [ 2.216158] ti-soc-thermal 4a0021e0.bandgap: thermal zone device is NULL [ 2.226008] mmc1: new DDR MMC card at address 0001 [ 2.231565] mmcblk1: mmc1:0001 Q2J55L 7.09 GiB [ 2.236603] mmcblk1boot0: mmc1:0001 Q2J55L partition 1 16.0 MiB [ 2.242969] mmcblk1boot1: mmc1:0001 Q2J55L partition 2 16.0 MiB [ 2.249213] mmcblk1rpmb: mmc1:0001 Q2J55L partition 3 4.00 MiB, chardev (244:0) [ 2.259687] mmcblk1: p1 p2 [ 2.264213] ti-soc-thermal 4a0021e0.bandgap: thermal zone device is NULL [ 2.716630] EXT4-fs (mmcblk0p2): recovery complete [ 2.724887] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) [ 2.733048] VFS: Mounted root (ext4 filesystem) on device 179:2. [ 2.748358] devtmpfs: mounted [ 2.752234] Freeing unused kernel memory: 2048K [ 2.756896] Run /sbin/init as init process [ 2.871898] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null) setting hostname: 5G_idefix creating static devices: rootdir=/ table='/etc/device_table.txt' ok Starting syslogd: OK Starting klogd: OK Populating /dev using udev: [ 3.060660] udevd[96]: starting version 3.2.7 [ 3.096522] random: udevd: uninitialized urandom read (16 bytes read) [ 3.104615] random: udevd: uninitialized urandom read (16 bytes read) [ 3.111153] random: udevd: uninitialized urandom read (16 bytes read) [ 3.148304] udevd[97]: starting eudev-3.2.7 [ 3.413496] omap-rproc 58820000.ipu: ignoring dependency for device, assuming no driver [ 3.430777] omap-rproc 58820000.ipu: ignoring dependency for device, assuming no driver [ 3.439468] omap-rproc 58820000.ipu: assigned reserved memory node ipu1-memory@95800000 [ 3.448699] remoteproc remoteproc0: 58820000.ipu is available [ 3.456267] ti-soc-thermal 4a0021e0.bandgap: thermal zone device is NULL [ 3.463383] remoteproc remoteproc0: Direct firmware load for dra7-ipu1-fw.xem4 failed with error -2 [ 3.473438] omap-rproc 55020000.ipu: ignoring dependency for device, assuming no driver [ 3.481593] remoteproc remoteproc0: powering up 58820000.ipu [ 3.487375] omap-rproc 55020000.ipu: ignoring dependency for device, assuming no driver [ 3.495510] remoteproc remoteproc0: Direct firmware load for dra7-ipu1-fw.xem4 failed with error -2 [ 3.504625] omap-rproc 55020000.ipu: assigned reserved memory node ipu2-memory@9b800000 [ 3.512717] remoteproc remoteproc1: 55020000.ipu is available [ 3.518521] remoteproc remoteproc0: request_firmware failed: -2 [ 3.524583] remoteproc remoteproc1: Direct firmware load for dra7-ipu2-fw.xem4 failed with error -2 [ 3.571063] omap-rproc 40800000.dsp: ignoring dependency for device, assuming no driver [ 3.579129] remoteproc remoteproc1: powering up 55020000.ipu [ 3.621800] omap-rproc 40800000.dsp: ignoring dependency for device, assuming no driver [ 3.629946] remoteproc remoteproc1: Direct firmware load for dra7-ipu2-fw.xem4 failed with error -2 [ 3.644155] omap-rproc 40800000.dsp: assigned reserved memory node dsp1-memory@97800000 [ 3.684189] remoteproc remoteproc1: request_firmware failed: -2 [ 3.690556] ti-soc-thermal 4a0021e0.bandgap: thermal zone device is NULL [ 3.714232] remoteproc remoteproc2: 40800000.dsp is available [ 3.720181] omap-rproc 41000000.dsp: ignoring dependency for device, assuming no driver [ 3.739357] ti-soc-thermal 4a0021e0.bandgap: thermal zone device is NULL [ 3.781636] remoteproc remoteproc2: Direct firmware load for dra7-dsp1-fw.xe66 failed with error -2 [ 3.790870] omap-rproc 41000000.dsp: ignoring dependency for device, assuming no driver [ 3.801124] omap-rproc 41000000.dsp: assigned reserved memory node dsp2-memory@95000000 [ 3.819704] remoteproc remoteproc2: powering up 40800000.dsp [ 3.834898] remoteproc remoteproc2: Direct firmware load for dra7-dsp1-fw.xe66 failed with error -2 [ 3.863995] omap_rng 48090000.rng: Random Number Generator ver. 20 [ 3.870630] remoteproc remoteproc3: 41000000.dsp is available [ 3.877265] remoteproc remoteproc2: request_firmware failed: -2 [ 3.883896] ti-soc-thermal 4a0021e0.bandgap: thermal zone device is NULL [ 3.929771] remoteproc remoteproc3: Direct firmware load for dra7-dsp2-fw.xe66 failed with error -2 [ 3.941004] rtc-ds1307 0-0032: registered as rtc0 [ 3.947259] remoteproc remoteproc3: powering up 41000000.dsp [ 3.955330] omap-des 480a5000.des: OMAP DES hw accel rev: 2.2 [ 3.961900] Driver for 1-wire Dallas network protocol. [ 3.965586] ti-soc-thermal 4a0021e0.bandgap: thermal zone device is NULL [ 3.967243] remoteproc remoteproc3: Direct firmware load for dra7-dsp2-fw.xe66 failed with error -2 [ 3.984654] palmas-rtc 48070000.i2c:tps659038@58:tps659038_rtc: rtc core: registered 48070000.i2c:tps659038@58:tps659038_rtc as rtc1 [ 3.997914] omap-des 480a5000.des: will run requests pump with realtime priority [ 4.056642] CAN device driver interface [ 4.074949] remoteproc remoteproc3: request_firmware failed: -2 [ 4.081450] ti-soc-thermal 4a0021e0.bandgap: thermal zone device is NULL [ 4.082187] c_can_platform 4ae3c000.can: c_can_platform device registered (regs=(ptrval), irq=97) [ 4.088250] omap_hdq 480b2000.1w: OMAP HDQ Hardware Rev 0.:. Driver in Interrupt mode [ 4.128021] ti-soc-thermal 4a0021e0.bandgap: thermal zone device is NULL [ 4.136178] ti-soc-thermal 4a0021e0.bandgap: thermal zone device is NULL [ 4.157275] c_can_platform 48480000.can: c_can_platform device registered (regs=(ptrval), irq=98) [ 4.179478] ti-soc-thermal 4a0021e0.bandgap: thermal zone device is NULL [ 4.201944] omap_rtc 48838000.rtc: /aliases ID 0 not available [ 4.213690] omap_rtc 48838000.rtc: registered as rtc3 [ 4.234773] ti-soc-thermal 4a0021e0.bandgap: thermal zone device is NULL [ 4.252257] ti-soc-thermal 4a0021e0.bandgap: thermal zone device is NULL [ 4.282687] ti-soc-thermal 4a0021e0.bandgap: thermal zone device is NULL [ 4.306101] phy phy-4a084000.phy.3: Linked as a consumer to regulator.28 [ 4.313378] ti-soc-thermal 4a0021e0.bandgap: thermal zone device is NULL [ 4.322726] ti-soc-thermal 4a0021e0.bandgap: thermal zone device is NULL [ 4.331234] phy phy-4a085000.phy.4: Linked as a consumer to regulator.28 [ 4.339363] w1_master_driver w1_bus_master1: Attaching one wire slave 01.000000000000 crc 3d [ 4.350768] ti-soc-thermal 4a0021e0.bandgap: thermal zone device is NULL [ 4.360382] ti-soc-thermal 4a0021e0.bandgap: thermal zone device is NULL [ 4.383573] vpe 489d0000.vpe: loading firmware vpdma-1b8.bin [ 4.389330] vpe 489d0000.vpe: Direct firmware load for vpdma-1b8.bin failed with error -2 [ 4.404081] vpe 489d0000.vpe: couldn't get firmware [ 4.411287] ti-soc-thermal 4a0021e0.bandgap: thermal zone device is NULL [ 4.448674] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec [ 4.468638] SCSI subsystem initialized [ 4.494688] ti-soc-thermal 4a0021e0.bandgap: thermal zone device is NULL [ 4.511184] w1_master_driver w1_bus_master1: Family 1 for 01.000000000000.3d is not registered. [ 4.539558] omap-aes 4b500000.aes: OMAP AES hw accel rev: 3.3 [ 4.540444] ti-soc-thermal 4a0021e0.bandgap: thermal zone device is NULL [ 4.564688] omap-sham 4b101000.sham: hw accel on OMAP rev 4.3 [ 4.580971] omap-aes 4b500000.aes: will run requests pump with realtime priority [ 4.597947] ahci 4a140000.sata: forcing port_map 0x0 -> 0x1 [ 4.603586] ahci 4a140000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode [ 4.604223] ti-soc-thermal 4a0021e0.bandgap: thermal zone device is NULL [ 4.620168] omap-aes 4b700000.aes: OMAP AES hw accel rev: 3.3 [ 4.626626] ti-soc-thermal 4a0021e0.bandgap: thermal zone device is NULL [ 4.644387] omap-aes 4b700000.aes: will run requests pump with realtime priority [ 4.652192] ti-soc-thermal 4a0021e0.bandgap: thermal zone device is NULL [ 4.665767] ahci 4a140000.sata: flags: 64bit ncq sntf pm led clo only pmp pio slum part ccc apst [ 4.679866] scsi host0: ahci [ 4.683013] ata1: SATA max UDMA/133 mmio [mem 0x4a140000-0x4a1410ff] port 0x100 irq 89 [ 4.702080] ti-soc-thermal 4a0021e0.bandgap: thermal zone device is NULL [ 4.931787] dwc3 48890000.usb: Failed to get clk 'ref': -2 [ 4.939674] ti-soc-thermal 4a0021e0.bandgap: thermal zone device is NULL [ 4.946744] dwc3 488d0000.usb: Failed to get clk 'ref': -2 [ 4.953018] ti-soc-thermal 4a0021e0.bandgap: thermal zone device is NULL [ 4.988393] usbcore: registered new interface driver usbfs [ 4.994974] usbcore: registered new interface driver hub [ 5.000549] usbcore: registered new device driver usb [ 5.023492] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 5.029060] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 [ 5.037239] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x0000000002010010 [ 5.040867] ata1: SATA link down (SStatus 0 SControl 300) [ 5.046773] xhci-hcd xhci-hcd.0.auto: irq 183, io mem 0x48890000 [ 5.058463] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19 [ 5.067920] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.075558] usb usb1: Product: xHCI Host Controller [ 5.080897] usb usb1: Manufacturer: Linux 4.19.38 xhci-hcd [ 5.086548] usb usb1: SerialNumber: xhci-hcd.0.auto [ 5.091894] hub 1-0:1.0: USB hub found [ 5.095691] hub 1-0:1.0: 1 port detected [ 5.100152] ti-soc-thermal 4a0021e0.bandgap: thermal zone device is NULL [ 5.104661] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 5.107588] ti-soc-thermal 4a0021e0.bandgap: thermal zone device is NULL [ 5.112396] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 [ 5.126840] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed [ 5.133539] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 5.141792] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 4.19 [ 5.150106] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.157374] usb usb2: Product: xHCI Host Controller [ 5.162272] usb usb2: Manufacturer: Linux 4.19.38 xhci-hcd [ 5.167795] usb usb2: SerialNumber: xhci-hcd.0.auto [ 5.173262] hub 2-0:1.0: USB hub found [ 5.177070] hub 2-0:1.0: 1 port detected [ 5.181411] ti-soc-thermal 4a0021e0.bandgap: thermal zone device is NULL [ 5.184453] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 5.188879] ti-soc-thermal 4a0021e0.bandgap: thermal zone device is NULL [ 5.193835] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 [ 5.208455] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x0000000002010010 [ 5.217942] xhci-hcd xhci-hcd.1.auto: irq 184, io mem 0x488d0000 [ 5.224291] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.19 [ 5.232591] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.239861] usb usb3: Product: xHCI Host Controller [ 5.244839] usb usb3: Manufacturer: Linux 4.19.38 xhci-hcd [ 5.250348] usb usb3: SerialNumber: xhci-hcd.1.auto [ 5.255647] hub 3-0:1.0: USB hub found [ 5.259433] hub 3-0:1.0: 1 port detected [ 5.263763] ti-soc-thermal 4a0021e0.bandgap: thermal zone device is NULL [ 5.264616] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 5.270905] ti-soc-thermal 4a0021e0.bandgap: thermal zone device is NULL [ 5.276204] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4 [ 5.290579] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed [ 5.297305] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 5.305532] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 4.19 [ 5.313833] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.321127] usb usb4: Product: xHCI Host Controller [ 5.326037] usb usb4: Manufacturer: Linux 4.19.38 xhci-hcd [ 5.331544] usb usb4: SerialNumber: xhci-hcd.1.auto [ 5.337025] hub 4-0:1.0: USB hub found [ 5.340813] hub 4-0:1.0: 1 port detected [ 5.345144] ti-soc-thermal 4a0021e0.bandgap: thermal zone device is NULL [ 5.355032] ti-soc-thermal 4a0021e0.bandgap: thermal zone device is NULL done starting system clock handling (/dev/i2c-0) :modprobe: module rtc_pcf8563 not found in modules.dep ok Start monitoring BC: [ 5.624164] usb 3-1: new high-speed USB device number 2 using xhci-hcd [ 5.804423] usb 3-1: New USB device found, idVendor=0424, idProduct=2517, bcdDevice= 0.02 [ 5.812668] usb 3-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 5.873513] hub 3-1:1.0: USB hub found [ 5.877398] hub 3-1:1.0: 7 ports detected [ 5.938898] ti-soc-thermal 4a0021e0.bandgap: thermal zone device is NULL [ 6.254168] usb 3-1.3: new high-speed USB device number 3 using xhci-hcd [ 6.388308] usb 3-1.3: New USB device found, idVendor=1fc9, idProduct=0102, bcdDevice= 1.00 [ 6.396723] usb 3-1.3: New USB device strings: Mfr=1, Product=3, SerialNumber=0 [ 6.404066] usb 3-1.3: Product: NXP SAF510x (DFU Mode) [ 6.411762] usb 3-1.3: Manufacturer: NXP Semiconductors [ 6.422807] ti-soc-thermal 4a0021e0.bandgap: thermal zone device is NULL started Probing modules: modprobe: module spi-omap2-mcspi not found in modules.dep spi-omap2-mcspi failed modprobe: module d_can_platform not found in modules.dep d_can_platform failed [ 6.524223] usb 3-1.7: new high-speed USB device number 4 using xhci-hcd mcp251x loaded [ 6.539677] ti-soc-thermal 4a0021e0.bandgap: thermal zone device is NULL [ 6.548031] ti-soc-thermal 4a0021e0.bandgap: thermal zone device is NULL modprobe: module at86rf230 not found in modules.dep at86rf230 failed modprobe: module 6lowpan not found in modules.dep 6lowpan failed modprobe: module opticon not found in modules.dep opticon failed [ 6.606597] usbcore: registered new interface driver usb-storage usb-storage loaded modprobe: module sc16is7xx not found in modules.dep sc16is7xx failed Initializing random number generator... [ 6.649391] urandom_read: 2 callbacks suppressed [ 6.649394] random: dd: uninitialized urandom read (512 bytes read) done. Starting rngd: [ 6.674377] usb 3-1.7: New USB device found, idVendor=0424, idProduct=2422, bcdDevice= 0.a0 [ 6.682807] usb 3-1.7: New USB device strings: Mfr=0, Product=0, SerialNumber=0 OK [ 6.692311] random: crng init done Starting system message bus: [ 6.737514] hub 3-1.7:1.0: USB hub found [ 6.741520] hub 3-1.7:1.0: 2 ports detected [ 6.749107] ti-soc-thermal 4a0021e0.bandgap: thermal zone device is NULL done [ 7.054190] usb 3-1.2: new high-speed USB device number 5 using xhci-hcd older dimm-cpu-cb09 board detected unfortunately this isn't running on a dimm-cpu-cb09-h (or successor) board, so trying checking if modem is alive (0) stty: can't open '/dev/ttyO1': No such file or directory [ 7.195045] usb 3-1.2: New USB device found, idVendor=1546, idProduct=1146, bcdDevice= 1.00 [ 7.203440] usb 3-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 7.210815] usb 3-1.2: Product: MODEM-LTE [ 7.214869] usb 3-1.2: Manufacturer: u-blox [ 7.219072] usb 3-1.2: SerialNumber: 000000000100 [ 7.294174] usb 3-1.7.1: new full-speed USB device number 6 using xhci-hcd [ 7.315707] ti-soc-thermal 4a0021e0.bandgap: thermal zone device is NULL [ 7.346755] cdc_acm 3-1.2:1.2: ttyACM0: USB ACM device [ 7.352530] ti-soc-thermal 4a0021e0.bandgap: thermal zone device is NULL [ 7.359600] usbcore: registered new interface driver cdc_acm [ 7.366000] ti-soc-thermal 4a0021e0.bandgap: thermal zone device is NULL [ 7.372885] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters toggling modem state ... exporting GPIO 100 ... in=>out,1 ... ok checking if modem is alive (1) toggling modem state ... out=>in ... ok checking if modem is alive (2) toggling modem state ... in=>out,1 ... ok [ 22.504213] usb 3-1.7.1: device descriptor read/64, error -110 checking if modem is alive (3) toggling modem state ... out=>in ... ok modem activation failed, giving up after 4 tries Starting network... Configuration file: /etc/hostapd_wpa.conf [ 24.582989] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 24.634531] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 24.641159] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 [ 24.649907] cfg80211: failed to load regulatory.db Could not read interface wlan0 flags: No such device nl80211: Driver does not support authentication/association or connect commands nl80211: deinit ifname=wlan0 disabled_11b_rates=0 Could not read interface wlan0 flags: No such device nl80211 driver initialization failed. wlan0: interface state UNINITIALIZED->DISABLED wlan0: AP-DISABLED wlan0: CTRL-EVENT-TERMINATING hostapd_free_hapd_data: Interface wlan0 wasn't started Setting cpufreq governor: ondemand Starting gpsd: OK Starting gpspositiond: done Starting mosquitto: OK Starting nginx... Starting smsd: OK Starting sshd: OK Starting chrony network time protocol daemon: chronyd. Starting cron daemon: crond. Starting Network Interface Plugging Daemon: eth0[ 26.488630] net eth0: initializing cpsw version 1.15 (0) wlan1 eth1 usb0 wwan0 wlan0 ppp0. Connect to Server: aidageo.de [ 26.614820] Micrel KSZ9031 Gigabit PHY 48485000.mdio:01: attached PHY driver [Micrel KSZ9031 Gigabit PHY] (mii_bus:phy_addr=48485000.mdio:01, irq=POLL) symgmtd is deactivated by configuration || [ 26.665381] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready fw_download is deactivated by configuration |FALSE|[ 26.671810] net eth1: initializing cpsw version 1.15 (0) Starting mapcache: OK TeleExpert Service is deactivated by configuration |FALSE| Starting Device Watching Script:. starting vibration sensor handling (/dev/i2c-0) :ok Starting dnsmasq: [ 26.833115] Micrel KSZ9031 Gigabit PHY 48485000.mdio:02: attached PHY driver [Micrel KSZ9031 Gigabit PHY] (mii_bus:phy_addr=48485000.mdio:02, irq) [ 26.883242] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready OK file "/etc/conf.d/identification_mac.conf" successfully created. Creation of identification file(s) successful. gatekeeper is deactivated by configuration |FALSE| filter_app is deactivated by configuration |FALSE| amcanlogger is deactivated by configuration || iso_get_implements is deactivated by configuration |FALSE| plug_sense is deactivated by configuration |FALSE| /etc/init.d/rcS: configuration /media/disk/canlogger/can.conf doesn't exist /etc/init.d/rcS: applying configuration from /etc/conf.d/can.conf Starting CAN interfaces ... can0@250000[ 27.169988] c_can_platform 4ae3c000.can can0: setting BTR=1c04 BRPE=0000 [ 27.184321] IPv6: ADDRCONF(NETDEV_CHANGE): can0: link becomes ready can1@250000[ 27.246625] c_can_platform 48480000.can can1: setting BTR=1c04 BRPE=0000 [ 27.268589] IPv6: ADDRCONF(NETDEV_CHANGE): can1: link becomes ready dcs is deactivated by configuration |FALSE| dcs_data_transfer is deactivated by configuration |FALSE| dcs2Terminal is deactivated by configuration |FALSE| Starting wpa_supplicant:Successfully initialized wpa_supplicant Could not read interface wlan1 flags: No such device nl80211: Driver does not support authentication/association or connect commands nl80211: deinit ifname=wlan1 disabled_11b_rates=0 Could not read interface wlan1 flags: No such device wlan1: Failed to initialize driver interface [ 28.971836] cpsw 48484000.ethernet eth1: Link is Up - 100Mbps/Full - flow control rx/tx [ 28.990786] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready udhcpc: SIOCGIFINDEX: No such device . atd: created missing .SEQ file (atjobs will be lost on reboot) Starting atd: OK 5G_idefix login: [ 37.864214] usb 3-1.7.1: device descriptor read/64, error -110 [ 38.084211] usb 3-1.1: new high-speed USB device number 7 using xhci-hcd [ 38.237735] usb 3-1.1: config 1 has an invalid interface number: 8 but max is 4 [ 38.254164] usb 3-1.1: config 1 has an invalid interface number: 10 but max is 4 [ 38.281202] usb 3-1.1: config 1 has no interface number 1 [ 38.294155] usb 3-1.1: config 1 has no interface number 4 [ 38.319589] usb 3-1.1: New USB device found, idVendor=1199, idProduct=9071, bcdDevice= 0.06 [ 38.333078] usb 3-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 38.344196] usb 3-1.3: reset high-speed USB device number 3 using xhci-hcd [ 38.344889] usb 3-1.1: Product: Sierra Wireless MC7430 Qualcomm® Snapdragon�������� X7 LTE-A [ 38.359893] usb 3-1.1: Manufacturer: Sierra Wireless, Incorporated [ 38.374222] usb 3-1.1: SerialNumber: LU84218838011019 [ 38.504271] usb 3-1.3: device firmware changed [ 38.551121] usb 3-1.3: USB disconnect, device number 3 [ 38.560589] ti-soc-thermal 4a0021e0.bandgap: thermal zone device is NULL [ 38.604185] usb 3-1.7.1: new full-speed USB device number 8 using xhci-hcd [ 53.864201] usb 3-1.7.1: device descriptor read/64, error -110 [ 69.224223] usb 3-1.7.1: device descriptor read/64, error -110 [ 69.344348] usb 3-1.7-port1: attempt power cycle [ 69.444183] usb 3-1.3: new high-speed USB device number 9 using xhci-hcd [ 69.574770] usb 3-1.3: New USB device found, idVendor=1fc9, idProduct=0103, bcdDevice= 1.00 [ 69.583159] usb 3-1.3: New USB device strings: Mfr=1, Product=3, SerialNumber=0 [ 69.590531] usb 3-1.3: Product: MK5 SDR 802.11p RADIO - High Speed [ 69.596890] usb 3-1.3: Manufacturer: CohdaWireless Pty Ltd [ 69.605095] ti-soc-thermal 4a0021e0.bandgap: thermal zone device is NULL [ 69.731802] cw_llc: loading out-of-tree module taints kernel. [ 69.764813] LLC_USBSetup FNSTART: (pDrv a6bcfc73) [ 69.770577] LLC_USBOutReq: USB device not present [ 69.776927] LLC_USBOutReq: USB device not present [ 69.781940] LLC_USBOutReq: USB device not present [ 69.786746] LLC_USBOutReq: USB device not present [ 69.791805] LLC_USBOutReq: USB device not present [ 69.796565] LLC_USBOutReq: USB device not present [ 69.874263] LLC_USBInterfaceProbe: MKx now attached to USB as device 0 [ 69.874278] LLC_USBInterfaceProbe: Successfully attached to LLC USB device 2 [ 69.888044] usbcore: registered new interface driver cw-llc [ 69.894416] LLC_USBInWorkCallback: LLC_MsgRecv()= -22 [ 69.899508] ti-soc-thermal 4a0021e0.bandgap: thermal zone device is NULL [ 70.004172] usb 3-1.7.1: new full-speed USB device number 10 using xhci-hcd [ 75.044207] xhci-hcd xhci-hcd.1.auto: Timeout while waiting for setup device command [ 80.324214] xhci-hcd xhci-hcd.1.auto: Timeout while waiting for setup device command [ 80.544167] usb 3-1.7.1: device not accepting address 10, error -62 [ 80.644205] usb 3-1.7.1: new full-speed USB device number 11 using xhci-hcd [ 85.684210] xhci-hcd xhci-hcd.1.auto: Timeout while waiting for setup device command [ 90.964221] xhci-hcd xhci-hcd.1.auto: Timeout while waiting for setup device command [ 91.184164] usb 3-1.7.1: device not accepting address 11, error -62 [ 91.194404] usb 3-1.7-port1: unable to enumerate USB device [ 91.304165] usb 3-1.7.2: new full-speed USB device number 12 using xhci-hcd [ 91.435965] usb 3-1.7.2: New USB device found, idVendor=1546, idProduct=01a8, bcdDevice= 3.01 [ 91.444606] usb 3-1.7.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 91.452129] usb 3-1.7.2: Product: u-blox GNSS receiver [ 91.457606] usb 3-1.7.2: Manufacturer: u-blox AG - www.u-blox.com [ 91.506104] cdc_acm 3-1.7.2:1.0: ttyACM1: USB ACM device [ 91.515034] ti-soc-thermal 4a0021e0.bandgap: thermal zone device is NULL