02000000011a0000616d3632780000000000000048535345010001000100010002a6000002000200d68ecb2c055dff11ade95bd927e837d2a53bc23b0a2800cebce4f106bcf309df2213912d77a157a8b7c2df40672a06a918034aa4c7d603e462481475225d49b839109fc8da497caaca402cdb8566ccee2e94a6514077f4253513d2c9eabf277294ba87b257ba58d8bff4fb1797d5e6b6d2c6df8c07a210045e4ad37505f5be34e7f9a0180a54b90a2841c73f268690ad53a4a3a5be07c9e2dcb2e2cb90896a42C
U-Boot R5 SPL 2021.01-00015-gaa48999c6a (Oct 14 2024 - 10:02:03 +0700)
SYSFW ABI: 3.1 (firmware rev 0x0009 '9.0.5--v09.00.05 (Kool Koala)')
Switching: UART -> ETH RMII boot...
SPL initial stack usage: 13424 bytes
Trying to boot from eth device
eth0: ethernet@8000000port@1
ethernet@8000000port@1 PHY link status . is up(done)
ethernet@8000000port@1:100BASE-T1 100 Mbit/s
link up on port 1, speed 100, full duplex
Using ethernet@8000000port@1 device
TFTP from server 192.168.1.20; our IP address is 192.168.1.2
Filename 'tispl.bin'.
Load address: 0x82000000
Loading: #################
         1.6 MiB/s
done
Bytes transferred = 869192 (d4348 hex)
Authenticating image at address 0x9e780000
Authenticating image of size 49897 bytes
Authentication passed
Authenticating image at address 0x9e800000
Authenticating image of size 442065 bytes
Authentication passed
Authenticating image at address 0x89000000
Authenticating image of size 151589 bytes
Authentication passed
Authenticating image at address 0x80080000
Authenticating image of size 203721 bytes
Authentication passed
Authenticating image at address 0x800b1580
Authenticating image of size 20555 bytes
Authentication passed
init_env from device 4 not supported!
Starting ATF on ARM64 core...

NOTICE:  BL31: v2.8(release):v2.8-226-g2fcd408bb3-dirty
NOTICE:  BL31: Built : 00:42:57, Jan 13 2023

U-Boot A53 SPL 2021.01-00015-gaa48999c6a (Oct 14 2024 - 10:01:54 +0700)
SYSFW ABI: 3.1 (firmware rev 0x0009 '9.0.5--v09.00.05 (Kool Koala)')
Trying to boot from eth device
eth0: ethernet@8000000port@1
ethernet@8000000port@1 PHY link status  is up(done)
ethernet@8000000port@1:100BASE-T1 100 Mbit/s
link up on port 1, speed 100, full duplex
Using ethernet@8000000port@1 device
TFTP from server 192.168.1.20; our IP address is 192.168.1.2
Filename 'u-boot.img'.
Load address: 0x82000000
Loading: T ##############
         93.8 KiB/s
done
Bytes transferred = 668712 (a3428 hex)
Authenticating image at address 0x80800000
Authenticating image of size 634353 bytes
Authentication passed
Authenticating image at address 0x8089a780
Authenticating image of size 33358 bytes
Authentication passed


U-Boot 2021.01-00015-gaa48999c6a (Oct 14 2024 - 10:01:54 +0700)

SoC:   AM62X SR1.0 HS-SE
Model: Texas Instruments AM625 SK
DRAM:  512 MiB
MMC:
Error, wrong i2c adapter 0 max 0 possible
In:    serial@2800000
Out:   serial@2800000
Err:   serial@2800000
Net:   eth0: ethernet@8000000port@1
Hit any key to stop autoboot:  0
jedec_spi_nor flash@0: Issue 0xB7, This changes CFR2V[7] to 1 (4-byte addr mode)
CFR5N: 40 40
CFR4N: a8 a8
CFR3N: 08 00
CFR2N: 88 88
CFR1N: 00 04
STR1N: 00 00
The hybrid sector is already enabled (CFR3N[3]=0) of die-2
Already setting top 4KB (CFR1N[2]=1) of die-2
params->page_size:512
CFR3V: 18 10
non_uniform---> done
CFR3V: 38 30---> done
The 1rst die is already in DDR mode!!!
The 2nd die is already in DDR mode!!!
SF: Detected s28hs02gt with page size 512 Bytes, erase size 256 KiB, total 256 MiB
ethernet@8000000port@1 PHY link status  is up(done)
ethernet@8000000port@1:100BASE-T1 100 Mbit/s
link up on port 1, speed 100, full duplex
Using ethernet@8000000port@1 device
TFTP from server 192.168.1.20; our IP address is 192.168.1.2
Filename 'debrick.scr'.
Load address: 0x80000000
Loading: #
         834 KiB/s
done
Bytes transferred = 3419 (d5b hex)
## Executing script at 80000000