U-Boot SPL 2019.01-g078a3b8701 (Nov 26 2019 - 02:40:43 +0000) SYSFW ABI: 2.7 (firmware rev 0x0013 '19.9.0-v2019.09 (Terrific Llama') Trying to boot from MMC2 Starting ATF on ARM64 core... NOTICE: BL31: v2.2(release):ti2019.05-rc1 NOTICE: BL31: Built : 03:12:47, Nov 24 2019 I/TC: I/TC: OP-TEE version: ti2019.05-rc1-dev (gcc version 8.3.0 (GNU Toolchain for the A-profile Archit ecture 8.3-2019.03 (arm-rel-8.36))) #1 Sun Nov 24 03:11:59 UTC 2019 aarch64 I/TC: Initialized U-Boot SPL 2019.01-g078a3b8701 (Nov 26 2019 - 02:40:52 +0000) Detected: AM6-IDKAPPEVM rev E3 Trying to boot from MMC2 U-Boot 2019.01-g078a3b8701 (Nov 26 2019 - 02:40:52 +0000) SoC: AM654 PG 1.0 Model: Texas Instruments AM654 Base Board Board: AM6-COMPROCEVM rev E3 DRAM: 4 GiB MMC: sdhci@4f80000: 0, sdhci@04FA0000: 1 Loading Environment from MMC... OK In: serial Out: serial Err: serial Detected: AM6-IDKAPPEVM rev E3 Net: eth2: pruss0_eth Warning: cpsw_nuss@046000000 using MAC address from ROM , eth0: cpsw_nuss@046000000, eth1: pruss2_eth Hit any key to stop autoboot: 0 switch to partitions #0, OK mmc1 is current device SD/MMC found on device 1 ** Unable to read file boot.scr ** 1490 bytes read in 2 ms (727.5 KiB/s) Loaded env from uEnv.txt Importing environment from mmc1 ... Running uenvcmd ... 1 bytes read in 3 ms (0 Bytes/s) Already setup. 13338632 bytes read in 1103 ms (11.5 MiB/s) 73168 bytes read in 9 ms (7.8 MiB/s) 11325 bytes read in 2 ms (5.4 MiB/s) ## Flattened Device Tree blob at 82000000 Booting using the fdt blob at 0x82000000 Loading Device Tree to 00000000fddb4000, end 00000000fdec8fff ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034] [ 0.000000] Linux version 4.19.59-g5f8c1c6121 (gaonian@gaonian-SIMATIC-IPC3000-SMART) (gcc vers ion 8.3.0 (GNU Toolchain for the A-profile Architecture 8.3-2019.03 (arm-rel-8.36))) #1 SMP PREEMP T Sat Jan 11 19:52:58 CST 2020 [ 0.000000] Machine model: Texas Instruments AM654 Base Board [ 0.000000] earlycon: ns16550a0 at MMIO32 0x0000000002800000 (options '') [ 0.000000] bootconsole [ns16550a0] enabled [ 0.000000] Reserved memory: created DMA memory pool at 0x00000000a0000000, size 1 MiB [ 0.000000] OF: reserved mem: initialized node r5f-dma-memory@a0000000, compatible id shared-dm a-pool [ 0.000000] Reserved memory: created DMA memory pool at 0x00000000a0100000, size 15 MiB [ 0.000000] OF: reserved mem: initialized node r5f-memory@a0100000, compatible id shared-dma-po ol [ 0.000000] Reserved memory: created DMA memory pool at 0x00000000a1000000, size 1 MiB [ 0.000000] OF: reserved mem: initialized node r5f-dma-memory@a1000000, compatible id shared-dm a-pool [ 0.000000] Reserved memory: created DMA memory pool at 0x00000000a1100000, size 15 MiB [ 0.000000] OF: reserved mem: initialized node r5f-memory@a1100000, compatible id shared-dma-po ol [ 0.000000] cma: Reserved 512 MiB at 0x00000000c0000000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: Trusted OS migration not required [ 0.000000] psci: SMC Calling Convention v1.1 [ 0.000000] random: get_random_bytes called from start_kernel+0x94/0x3e4 with crng_init=0 [ 0.000000] percpu: Embedded 2 pages/cpu s52632 r8192 d70248 u131072 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] CPU features: enabling workaround for ARM erratum 845719 [ 0.000000] Speculative Store Bypass Disable mitigation not required [ 0.000000] CPU features: detected: Kernel page table isolation (KPTI) [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64544 [ 0.000000] Kernel command line: console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000 mtd parts=47040000.spi.0:512k(ospi.tiboot3),2m(ospi.tispl),4m(ospi.u-boot),128k(ospi.env),128k(ospi.en v.backup),1m(ospi.sysfw),-@8m(ospi.rootfs) root=PARTUUID=90d6f3c9-02 rw rootfstype=ext4 rootwait [ 0.000000] Dentry cache hash table entries: 524288 (order: 6, 4194304 bytes) [ 0.000000] Inode-cache hash table entries: 262144 (order: 5, 2097152 bytes) [ 0.000000] software IO TLB: mapped [mem 0xf9db0000-0xfddb0000] (64MB) [ 0.000000] Memory: 3518848K/4134912K available (8510K kernel code, 738K rwdata, 3136K rodata, 576K init, 642K bss, 91776K reserved, 524288K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4. [ 0.000000] Tasks RCU enabled. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode [ 0.000000] GICv3: Distributor has no Range Selector support [ 0.000000] GICv3: no VLPI support, no direct LPI support [ 0.000000] ITS [mem 0x01820000-0x0182ffff] [ 0.000000] GIC: enabling workaround for ITS: Socionext Synquacer pre-ITS [ 0.000000] ITS@0x0000000001820000: allocated 1048576 Devices @8c0800000 (flat, esz 8, psz 64K, shr 0) [ 0.000000] ITS: using cache flushing for cmd queue [ 0.000000] GIC: using LPI property table @0x00000008c00c0000 [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000001880000 [ 0.000000] CPU0: using LPI pending table @0x00000008c00d0000 [ 0.000000] GIC: using cache flushing for LPI property table [ 0.000000] arch_timer: cp15 timer(s) running at 200.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2e2049d3e8, max _idle_ns: 440795210634 ns [ 0.000006] sched_clock: 56 bits at 200MHz, resolution 5ns, wraps every 4398046511102ns [ 0.008695] Console: colour dummy device 80x25 [ 0.013289] Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 B ogoMIPS (lpj=800000) [ 0.023980] pid_max: default: 32768 minimum: 301 [ 0.028802] Security Framework initialized [ 0.033063] Mount-cache hash table entries: 8192 (order: 0, 65536 bytes) [ 0.039944] Mountpoint-cache hash table entries: 8192 (order: 0, 65536 bytes) [ 0.071381] ASID allocator initialised with 32768 entries [ 0.084948] rcu: Hierarchical SRCU implementation. [ 0.098030] Platform MSI: gic-its@1820000 domain created [ 0.103781] PCI/MSI: /interconnect@100000/interrupt-controller@1800000/gic-its@1820000 domain c reated [ 0.121261] smp: Bringing up secondary CPUs ... [ 0.158378] Detected VIPT I-cache on CPU1 [ 0.158417] GICv3: CPU1: found redistributor 1 region 0:0x00000000018a0000 [ 0.158474] CPU1: using LPI pending table @0x00000008c0330000 [ 0.158521] CPU1: Booted secondary processor 0x0000000001 [0x410fd034] [ 0.220087] Detected VIPT I-cache on CPU2 [ 0.220130] GICv3: CPU2: found redistributor 100 region 0:0x00000000018c0000 [ 0.220192] CPU2: using LPI pending table @0x00000008c03c0000 [ 0.220242] CPU2: Booted secondary processor 0x0000000100 [0x410fd034] [ 0.252484] Detected VIPT I-cache on CPU3 [ 0.252512] GICv3: CPU3: found redistributor 101 region 0:0x00000000018e0000 [ 0.252570] CPU3: using LPI pending table @0x00000008c0450000 [ 0.252605] CPU3: Booted secondary processor 0x0000000101 [0x410fd034] [ 0.252747] smp: Brought up 1 node, 4 CPUs [ 0.328383] SMP: Total of 4 processors activated. [ 0.333202] CPU features: detected: GIC system register CPU interface [ 0.339814] CPU features: detected: 32-bit EL0 Support [ 0.371957] CPU: All CPU(s) started at EL2 [ 0.376177] alternatives: patching kernel code [ 0.382229] devtmpfs: initialized [ 0.398077] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041 785100000 ns [ 0.408070] futex hash table entries: 1024 (order: 0, 65536 bytes) [ 0.415791] pinctrl core: initialized pinctrl subsystem [ 0.422104] NET: Registered protocol family 16 [ 0.427933] vdso: 2 pages (1 code @ (____ptrval____), 1 data @ (____ptrval____)) [ 0.435521] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.448967] DMA: preallocated 256 KiB pool for atomic allocations [ 0.476965] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages [ 0.483846] HugeTLB registered 512 MiB page size, pre-allocated 0 pages [ 0.492681] cryptd: max_cpu_qlen set to 1000 [ 0.499089] SCSI subsystem initialized [ 0.503582] media: Linux media interface: v0.10 [ 0.508257] videodev: Linux video capture interface: v2.00 [ 0.513913] pps_core: LinuxPPS API ver. 1 registered [ 0.518997] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.528358] PTP clock support registered [ 0.532397] EDAC MC: Ver: 3.0.0 [ 0.536989] Advanced Linux Sound Architecture Driver Initialized. [ 0.544206] clocksource: Switched to clocksource arch_sys_counter [ 0.550663] VFS: Disk quotas dquot_6.6.0 [ 0.554777] VFS: Dquot-cache hash table entries: 8192 (order 0, 65536 bytes) [ 0.569312] NET: Registered protocol family 2 [ 0.574481] tcp_listen_portaddr_hash hash table entries: 4096 (order: 0, 65536 bytes) [ 0.582632] TCP established hash table entries: 32768 (order: 2, 262144 bytes) [ 0.590328] TCP bind hash table entries: 32768 (order: 3, 524288 bytes) [ 0.597681] TCP: Hash tables configured (established 32768 bind 32768) [ 0.604509] UDP hash table entries: 2048 (order: 0, 65536 bytes) [ 0.610787] UDP-Lite hash table entries: 2048 (order: 0, 65536 bytes) [ 0.617669] NET: Registered protocol family 1 [ 0.622740] RPC: Registered named UNIX socket transport module. [ 0.628823] RPC: Registered udp transport module. [ 0.633641] RPC: Registered tcp transport module. [ 0.638457] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.646239] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available [ 0.659387] Initialise system trusted keyrings [ 0.664162] workingset: timestamp_bits=46 max_order=16 bucket_order=0 [ 0.676269] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.682946] NFS: Registering the id_resolver key type [ 0.688149] Key type id_resolver registered [ 0.692441] Key type id_legacy registered [ 0.696559] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.703597] 9p: Installing v9fs 9p2000 file system support [ 0.714199] Key type asymmetric registered [ 0.718413] Asymmetric key parser 'x509' registered [ 0.723468] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245) [ 0.731046] io scheduler noop registered [ 0.735063] io scheduler deadline registered [ 0.739689] io scheduler cfq registered (default) [ 0.744518] io scheduler mq-deadline registered [ 0.749160] io scheduler kyber registered [ 0.755571] pinctrl-single 4301c000.pinmux: 70 pins, size 280 [ 0.762165] pinctrl-single 11c000.pinmux: 185 pins, size 740 [ 0.768111] pinctrl-single 11c2e8.pinmux: 9 pins, size 36 [ 0.774820] pinctrl-single a40000.timesync_router: 512 pins, size 2048 [ 0.792006] Serial: 8250/16550 driver, 10 ports, IRQ sharing enabled [ 0.815223] brd: module loaded [ 0.825934] loop: module loaded [ 0.832268] libphy: Fixed MDIO Bus: probed [ 0.837040] tun: Universal TUN/TAP device driver, 1.6 [ 0.842993] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k [ 0.851018] igbvf: Copyright (c) 2009 - 2012 Intel Corporation. [ 0.857133] sky2: driver version 1.30 [ 0.863719] VFIO - User Level meta-driver version: 0.3 [ 0.869950] i2c /dev entries driver [ 0.874918] sdhci: Secure Digital Host Controller Interface driver [ 0.881260] sdhci: Copyright(c) Pierre Ossman [ 0.886254] sdhci-pltfm: SDHCI platform and OF driver helper [ 0.893361] ledtrig-cpu: registered to indicate activity on CPUs [ 0.899616] ti-sci interconnect@100000:interconnect@28380000:interconnect@42040000:dmsc: invali d resource [ 0.911512] optee: probing for conduit method from DT. [ 0.916829] optee: revision 3.7 (5208e5c1) [ 0.917127] optee: initialized driver [ 0.926446] NET: Registered protocol family 17 [ 0.931163] 9pnet: Installing 9P2000 support [ 0.935595] Key type dns_resolver registered [ 0.940700] registered taskstats version 1 [ 0.944900] Loading compiled-in X.509 certificates [ 0.965083] ti-sci interconnect@100000:interconnect@28380000:interconnect@42040000:dmsc: invali d resource [ 0.975082] ti-sci interconnect@100000:interconnect@28380000:interconnect@42040000:dmsc: ABI: 2 .7 (firmware rev 0x0013 '19.9.0-v2019.09 (Terrific Llama') [ 1.009210] random: fast init done [ 1.444879] omap_i2c 42120000.i2c: bus 0 rev0.12 at 400 kHz [ 1.451304] omap_i2c 40b00000.i2c: bus 1 rev0.12 at 100 kHz [ 1.457802] pca953x 2-0041: 2-0041 supply vcc not found, using dummy regulator [ 1.465267] pca953x 2-0041: Linked as a consumer to regulator.0 [ 1.492946] pca953x 2-0021: 2-0021 supply vcc not found, using dummy regulator [ 1.500389] pca953x 2-0021: Linked as a consumer to regulator.0 [ 1.507130] omap_i2c 2000000.i2c: bus 2 rev0.12 at 400 kHz [ 1.513398] omap_i2c 2010000.i2c: bus 3 rev0.12 at 400 kHz [ 1.519660] omap_i2c 2020000.i2c: bus 4 rev0.12 at 400 kHz [ 1.525870] omap_i2c 2030000.i2c: bus 5 rev0.12 at 100 kHz [ 1.540937] remoteproc remoteproc0: b034000.pru is available [ 1.546797] pru-rproc b034000.pru: PRU rproc node pru@b034000 probed successfully [ 1.555026] remoteproc remoteproc1: b004000.rtu is available [ 1.560867] pru-rproc b004000.rtu: PRU rproc node rtu@b004000 probed successfully [ 1.569088] remoteproc remoteproc2: b038000.pru is available [ 1.574929] pru-rproc b038000.pru: PRU rproc node pru@b038000 probed successfully [ 1.583173] remoteproc remoteproc3: b006000.rtu is available [ 1.589017] pru-rproc b006000.rtu: PRU rproc node rtu@b006000 probed successfully [ 1.636243] davinci_mdio b032400.mdio: davinci mdio revision 1.7, bus freq 1000000 [ 1.644002] libphy: b032400.mdio: probed [ 1.649862] davinci_mdio b032400.mdio: phy[0]: device b032400.mdio:00, driver TI DP83867 [ 1.658161] davinci_mdio b032400.mdio: phy[3]: device b032400.mdio:03, driver TI DP83867 [ 1.671736] remoteproc remoteproc4: b134000.pru is available [ 1.677610] pru-rproc b134000.pru: PRU rproc node pru@b134000 probed successfully [ 1.685869] remoteproc remoteproc5: b104000.rtu is available [ 1.691717] pru-rproc b104000.rtu: PRU rproc node rtu@b104000 probed successfully [ 1.699947] remoteproc remoteproc6: b138000.pru is available [ 1.705791] pru-rproc b138000.pru: PRU rproc node pru@b138000 probed successfully [ 1.714020] remoteproc remoteproc7: b106000.rtu is available [ 1.719866] pru-rproc b106000.rtu: PRU rproc node rtu@b106000 probed successfully [ 1.764226] davinci_mdio b132400.mdio: davinci mdio revision 1.7, bus freq 1000000 [ 1.771986] libphy: b132400.mdio: probed [ 1.777729] davinci_mdio b132400.mdio: phy[0]: device b132400.mdio:00, driver TI DP83867 [ 1.786028] davinci_mdio b132400.mdio: phy[3]: device b132400.mdio:03, driver TI DP83867 [ 1.799522] remoteproc remoteproc8: b234000.pru is available [ 1.805392] pru-rproc b234000.pru: PRU rproc node pru@b234000 probed successfully [ 1.813626] remoteproc remoteproc9: b204000.rtu is available [ 1.819472] pru-rproc b204000.rtu: PRU rproc node rtu@b204000 probed successfully [ 1.827701] remoteproc remoteproc10: b238000.pru is available [ 1.833634] pru-rproc b238000.pru: PRU rproc node pru@b238000 probed successfully [ 1.841868] remoteproc remoteproc11: b206000.rtu is available [ 1.847804] pru-rproc b206000.rtu: PRU rproc node rtu@b206000 probed successfully [ 1.892225] davinci_mdio b232400.mdio: davinci mdio revision 1.7, bus freq 1000000 [ 1.899982] libphy: b232400.mdio: probed [ 1.905639] davinci_mdio b232400.mdio: phy[0]: device b232400.mdio:00, driver TI DP83867 [ 1.913934] davinci_mdio b232400.mdio: phy[3]: device b232400.mdio:03, driver TI DP83867 [ 1.922659] k3-ringacc 2b800000.ringacc: Ring Accelerator probed rings:286, gp-rings[96,160] sc i-dev-id:195 [ 1.932641] k3-ringacc 2b800000.ringacc: dma-ring-reset-quirk: enabled [ 1.939335] k3-ringacc 2b800000.ringacc: RA Proxy rev. 66344100, num_proxies:64 [ 1.947229] k3-ringacc 3c000000.ringacc: Ring Accelerator probed rings:818, gp-rings[304,464] s ci-dev-id:187 [ 1.957304] k3-ringacc 3c000000.ringacc: dma-ring-reset-quirk: enabled [ 1.963997] k3-ringacc 3c000000.ringacc: RA Proxy rev. 66344100, num_proxies:64 [ 1.971825] omap8250 40a00000.serial: PM domain pd:149 will not be powered off [ 1.979570] 40a00000.serial: ttyS1 at MMIO 0x40a00000 (irq = 8, base_baud = 6000000) is a 8250 [ 1.989242] 2800000.serial: ttyS2 at MMIO 0x2800000 (irq = 22, base_baud = 3000000) is a 8250 [ 1.998012] console [ttyS2] enabled [ 1.998012] console [ttyS2] enabled [ 2.005067] bootconsole [ns16550a0] disabled [ 2.005067] bootconsole [ns16550a0] disabled [ 2.014416] 2810000.serial: ttyS3 at MMIO 0x2810000 (irq = 23, base_baud = 3000000) is a 8250 [ 2.023635] 2820000.serial: ttyS4 at MMIO 0x2820000 (irq = 24, base_baud = 3000000) is a 8250 [ 2.035578] cadence-qspi 47040000.spi: mt35xu512aba (65536 Kbytes) [ 2.041794] 7 cmdlinepart partitions found on MTD device 47040000.spi.0 [ 2.048409] Creating 7 MTD partitions on "47040000.spi.0": [ 2.053905] 0x000000000000-0x000000080000 : "ospi.tiboot3" [ 2.060271] 0x000000080000-0x000000280000 : "ospi.tispl" [ 2.066274] 0x000000280000-0x000000680000 : "ospi.u-boot" [ 2.072345] 0x000000680000-0x0000006a0000 : "ospi.env" [ 2.078114] 0x0000006a0000-0x0000006c0000 : "ospi.env.backup" [ 2.084572] 0x0000006c0000-0x0000007c0000 : "ospi.sysfw" [ 2.090543] 0x000000800000-0x000004000000 : "ospi.rootfs" [ 2.208460] cadence-qspi 47040000.spi: Cadence QSPI NOR probe failed -517 [ 2.223102] am65-cpsw-nuss 46000000.ethernet: rx-flow-id-base is not set -22 [ 2.230224] am65-cpsw-nuss 46000000.ethernet: initializing am65 cpsw nuss version 0x6BA07100, c psw version 0x6BA80100 Ports: 2 [ 2.241750] UDMA has not been proped [ 2.245406] am65-cpsw-nuss 46000000.ethernet: Failed to request tx dma channel -517 [ 2.255418] am65-cpts 310d0000.cpts: CPTS ver 0x4e8a2109, freq:200000000, add_val:4 pps:0 [ 2.292441] icssg-prueth pruss1_eth: TI PRU ethernet initialized: dual EMAC mode, dual_icssg 0 [ 2.329755] icssg-prueth pruss0_eth: TI PRU ethernet initialized: dual EMAC mode, dual_icssg 0 [ 2.360097] icssg-prueth pruss2_eth: TI PRU ethernet initialized: dual EMAC mode, dual_icssg 0 [ 2.370212] keystone-wdt 40610000.rti: heartbeat 60 sec [ 2.376512] mmc0: Unknown controller version (4). You may experience problems. [ 2.383871] mmc0: CQHCI version 5.10 [ 2.418540] mmc0: SDHCI controller on 4f80000.sdhci [4f80000.sdhci] using ADMA 64-bit [ 2.427250] mmc1: Unknown controller version (4). You may experience problems. [ 2.434656] mmc1: CQHCI version 5.10 [ 2.469299] mmc1: SDHCI controller on 4fa0000.sdhci [4fa0000.sdhci] using ADMA 64-bit [ 2.485832] mmc0: new HS200 MMC card at address 0001 [ 2.491953] mmcblk0: mmc0:0001 R1J56L 14.7 GiB [ 2.497324] mmcblk0boot0: mmc0:0001 R1J56L partition 1 8.00 MiB [ 2.507463] pca953x 0-0039: 0-0039 supply vcc not found, using dummy regulator [ 2.514796] mmcblk0boot1: mmc0:0001 R1J56L partition 2 8.00 MiB [ 2.520866] pca953x 0-0039: Linked as a consumer to regulator.0 [ 2.526836] mmcblk0rpmb: mmc0:0001 R1J56L partition 3 4.00 MiB, chardev (243:0) [ 2.535776] mmcblk0: p1 [ 2.549857] omap-mailbox 31f80000.mailbox: omap mailbox rev 0x66fc5900 [ 2.556854] omap-mailbox 31f81000.mailbox: omap mailbox rev 0x66fc5900 [ 2.564418] ti-udma 285c0000.udmap: Channels: 96 (tchan: 48, echan: 0, rchan: 48, rflow: 96) [ 2.579370] ti-udma 31150000.udmap: Channels: 267 (tchan: 120, echan: 32, rchan: 150, rflow: 30 0) [ 2.605644] cadence-qspi 47040000.spi: mt35xu512aba (65536 Kbytes) [ 2.611862] 7 cmdlinepart partitions found on MTD device 47040000.spi.0 [ 2.618486] Creating 7 MTD partitions on "47040000.spi.0": [ 2.623975] 0x000000000000-0x000000080000 : "ospi.tiboot3" [ 2.630380] 0x000000080000-0x000000280000 : "ospi.tispl" [ 2.636367] 0x000000280000-0x000000680000 : "ospi.u-boot" [ 2.642436] 0x000000680000-0x0000006a0000 : "ospi.env" [ 2.648271] 0x0000006a0000-0x0000006c0000 : "ospi.env.backup" [ 2.654655] 0x0000006c0000-0x0000007c0000 : "ospi.sysfw" [ 2.660728] 0x000000800000-0x000004000000 : "ospi.rootfs" [ 2.674138] m25p80 spi7.0: unrecognized JEDEC id bytes: 30, ff, 1f [ 2.680358] m25p80: probe of spi7.0 failed with error -2 [ 2.686318] am65-cpsw-nuss 46000000.ethernet: rx-flow-id-base is not set -22 [ 2.693416] am65-cpsw-nuss 46000000.ethernet: initializing am65 cpsw nuss version 0x6BA07100, c psw version 0x6BA80100 Ports: 2 [ 2.714535] am65-cpsw-nuss 46000000.ethernet: set new flow-id-base 48 [ 2.728569] pps pps0: new PPS source ptp7 [ 2.732801] am65-cpsw-nuss 46000000.ethernet: CPTS ver 0x4e8a2109, freq:200000000, add_val:4 pp s:1 [ 2.741795] am65-cpsw-nuss 46000000.ethernet: initialized cpsw ale version 0.4 [ 2.749022] am65-cpsw-nuss 46000000.ethernet: ALE Table size 64 [ 2.792223] am65-cpsw-nuss 46000000.ethernet: davinci mdio revision 9.7, bus freq 1000000 [ 2.800400] libphy: 46000000.ethernet: probed [ 2.808408] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 2.815487] hctosys: unable to open rtc device (rtc0) [ 2.918784] ALSA device list: [ 2.921773] No soundcards found. [ 2.925808] Waiting for root device PARTUUID=90d6f3c9-02... [ 3.665903] mmc1: new high speed SDXC card at address aaaa [ 3.672571] mmcblk1: mmc1:aaaa SC64G 59.5 GiB [ 3.684270] mmcblk1: p1 p2 [ 3.716137] EXT4-fs (mmcblk1p2): warning: mounting fs with errors, running e2fsck is recommende d [ 3.730946] EXT4-fs (mmcblk1p2): mounted filesystem with ordered data mode. Opts: (null) [ 3.739116] VFS: Mounted root (ext4 filesystem) on device 179:98. [ 3.754924] devtmpfs: mounted [ 3.758207] Freeing unused kernel memory: 576K [ 3.762698] Run /sbin/init as init process [ 4.126148] systemd[1]: System time before build time, advancing clock. [ 4.196035] systemd[1]: systemd 239 running in system mode. (+PAM -AUDIT -SELINUX +IMA -APPARMO R +SMACK +SYSVINIT +UTMP -LIBCRYPTSETUP -GCRYPT -GNUTLS +ACL +XZ -LZ4 -SECCOMP +BLKID -ELFUTILS +K MOD -IDN2 -IDN -PCRE2 default-hierarchy=hybrid) [ 4.217771] systemd[1]: Detected architecture arm64. Welcome to Arago 2019.11! [ 4.267176] systemd[1]: Set hostname to . [ 4.468695] systemd[1]: File /lib/systemd/system/systemd-journald.service:36 configures an IP f irewall (IPAddressDeny=any), but the local system does not support BPF/cgroup based firewalling. [ 4.485752] systemd[1]: Proceeding WITHOUT firewalling in effect! (This warning is only shown f or the first loaded unit using IP firewalling.) [ 4.745079] random: systemd: uninitialized urandom read (16 bytes read) [ 4.752392] systemd[1]: Listening on Journal Socket. [ OK ] Listening on Journal Socket. [ 4.768635] random: systemd: uninitialized urandom read (16 bytes read) [ 4.781353] systemd[1]: Mounting Kernel Debug File System... Mounting Kernel Debug File System... [ 4.800635] random: systemd: uninitialized urandom read (16 bytes read) [ 4.807901] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. [ 4.824772] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). [ 4.844829] systemd[1]: Listening on Network Service Netlink Socket. [ OK ] Listening on Network Service Netlink Socket. Starting Load Kernel Modules... [ OK ] Reached target Swap. [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ OK ] Created slice User and Session Slice. [ OK ] Created slice system-serial\x2dgetty.slice. Mounting Temporary Directory (/tmp)... [ OK ] Listening on Process Core Dump Socket. Mounting POSIX Message Queue File System... [ OK ] Listening on udev Control Socket. Starting udev Coldplug all Devices... [ OK ] Reached target Remote File Systems. [ OK ] Created slice system-getty.slice. [ OK ] Started Forward Password Requests to Wall Directory Watch. [ OK ] Reached target Paths. [ OK ] Listening on initctl Compatibility Named Pipe. Mounting Huge Pages File System... Starting Journal Service... [ OK ] Started Hardware RNG Entropy Gatherer Daemon. Starting Remount Root and Kernel File Systems... [ OK ] Reached target Slices. [ 5.222669] EXT4-fs (mmcblk1p2): re-mounted. Opts: (null) [ OK ] Mounted Kernel Debug File System. [FAILED] Failed to start Load Kernel Modules. See 'systemctl status systemd-modules-load.service' for details. [ OK ] Started Journal Service. [ OK ] Mounted Temporary Directory (/tmp). [ OK ] Mounted POSIX Message Queue File System. [ OK ] Mounted Huge Pages File System. [ OK ] Started Remount Root and Kernel File Systems. Starting Create Static Device Nodes in /dev... Starting Flush Journal to Persistent Storage... Starting Apply Kernel Variables... Mounting Kernel Configuration File System... [ OK ] Started Create Static Device Nodes in /dev. [ OK ] Started Apply Kernel Variables. [ OK ] Mounted Kernel Configuration File System. Starting udev Kernel Device Manager... [ OK ] Reached target Local File Systems (Pre). [ OK ] Reached target Containers. Mounting /var/volatile... Mounting /media/ram... [ OK ] Mounted /var/volatile. [ OK ] Mounted /media/ram. [ 5.645832] systemd-journald[167]: Received request to flush runtime journal from PID 1 Starting Load/Save Random Seed... [ OK ] Reached target Local File Systems. [ OK ] Started udev Kernel Device Manager. [ OK ] Started Flush Journal to Persistent Storage. [ OK ] Started Load/Save Random Seed. Starting Create Volatile Files and Directories... [ OK ] Started Create Volatile Files and Directories. Starting Update UTMP about System Boot/Shutdown... Starting Network Service... Starting Network Time Synchronization... [ OK ] Started udev Coldplug all Devices. [ OK ] Started Update UTMP about System Boot/Shutdown. [ OK ] Started Network Service. Starting Network Name Resolution... Starting Wait for Network to be Configured... [ OK ] Found device /dev/ttyS2. [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Initialization. [ OK ] Listening on D-Bus System Message Bus Socket. Starting Reboot and dump vmcore via kexec... [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Listening on RPCbind Server Activation Socket. [ OK ] Listening on dropbear.socket. [ OK ] Listening on Avahi mDNS/DNS-SD Stack Activation Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started Periodic Command Scheduler. Starting TI IPC Daemon... [ OK ] Started irqbalance daemon. [ OK ] Started Job spooling tools. Starting Login Service... [ OK ] Started D-Bus System Message Bus. [ OK ] Started TEE Supplicant. Starting RPC Bind Service... Starting LSB: Raise network interfaces and configure them... Starting Print notice about GPLv3 packages... [ OK ] Reached target System Time Synchronized. [ OK ] Started Daily rotation of log files. [ OK ] Reached target Timers. [ OK ] Started Network Name Resolution. [ OK ] Started Reboot and dump vmcore via kexec. [ OK ] Started TI IPC Daemon. [ OK ] Found device /dev/ttyS1. Starting Avahi mDNS/DNS-SD Stack... [ OK ] Reached target Host and Network Name Lookups. [ OK ] Reached target Network. Starting Simple Network Management Protocol (SNMP) Daemon.... Starting Permit User Sessions... Starting Lightning Fast Webserver With Light System Requirements... [ OK ] Started RPC Bind Service. [ OK ] Started NFS status monitor for NFSv2/3 locking.. [ OK ] Started Login Service. [ OK ] Started Permit User Sessions. [ 7.016258] remoteproc remoteproc4: powering up b134000.pru [ OK ] Started Getty on tty1. [ 7.039724] remoteproc remoteproc4: Booting fw image ti-pruss/am65x-pru0-prueth-fw.elf, size 16 468 [ OK ] Started Serial Getty on ttyS1. [ 7.055298] remoteproc remoteproc4: remote processor b134000.pru is now up [ OK ] Started Serial Getty on ttyS2. [ 7.065198] remoteproc remoteproc5: powering up b104000.rtu [ OK ] Reached target Login Prompts. [ 7.086766] remoteproc remoteproc5: Booting fw image ti-pruss/am65x-rtu0-prueth-fw.elf , size 15544 Starting Synchronize System and HW clocks... [ 7.098892] remoteproc remoteproc5: remote processor b104000.rtu is now up [ 7.109605] net eth0: started [FAILED] Failed to start Synchronize System and HW clocks. See 'systemctl status sync-clocks.service' for details. [ OK ] Started Avahi mDNS/DNS-SD Stack. [ 7.137208] TI DP83867 k3-cpsw-mdio:00: attached PHY driver [TI DP83867] (mii_bus:phy_addr=k3-c psw-mdio:00, irq=POLL) [ OK ] Started Lightning Fast Webserver With Light System Requirements. [ 7.943875] remoteproc remoteproc2: powering up b038000.pru [ 7.960864] remoteproc remoteproc2: Booting fw image ti-pruss/am65x-pru1-prueth-fw.elf, size 16 468 [ 7.972739] remoteproc remoteproc2: remote processor b038000.pru is now up [ 7.979815] remoteproc remoteproc3: powering up b006000.rtu [ 7.987808] remoteproc remoteproc3: Booting fw image ti-pruss/am65x-rtu1-prueth-fw.elf, size 15 544 [ 8.000364] remoteproc remoteproc3: remote processor b006000.rtu is now up [ 8.008892] net eth3: started [ 8.096433] remoteproc remoteproc6: powering up b138000.pru [ 8.102608] remoteproc remoteproc6: Booting fw image ti-pruss/am65x-pru1-prueth-fw.elf, size 16 468 [ 8.116402] remoteproc remoteproc6: remote processor b138000.pru is now up [ 8.127127] remoteproc remoteproc7: powering up b106000.rtu [ 8.133444] remoteproc remoteproc7: Booting fw image ti-pruss/am65x-rtu1-prueth-fw.elf, size 15 544 [ OK [ 8.142859] remoteproc remoteproc7: remote processor b106000.rtu is now up ] Created slice system-systemd\x2dfsck.slice. [ 8.156186] net eth1: started [ 8.192536] am65-cpsw-nuss 46000000.ethernet eth6: Link is Down [ 8.208493] remoteproc remoteproc10: powering up b238000.pru [ 8.214775] remoteproc remoteproc10: Booting fw image ti-pruss/am65x-pru1-prueth-fw.elf, size 1 6468 [ 8.226436] remoteproc remoteproc10: remote processor b238000.pru is now up [ 8.235137] remoteproc remoteproc11: powering up b206000.rtu [ 8.242900] remoteproc remoteproc11: Booting fw image ti-pruss/am65x-rtu1-prueth-fw.elf, size 1 5544 [ 8.253614] remoteproc remoteproc11: remote processor b206000.rtu is now up [ 8.262231] net eth5: started [ 8.292407] remoteproc remoteproc0: powering up b034000.pru [ 8.298621] remoteproc remoteproc0: Booting fw image ti-pruss/am65x-pru0-prueth-fw.elf, size 16 468 [ 8.307792] remoteproc remoteproc0: remote processor b034000.pru is now up [ 8.317070] remoteproc remoteproc1: powering up b004000.rtu [ 8.323280] remoteproc remoteproc1: Booting fw image ti-pruss/am65x-rtu0-prueth-fw.elf, size 15 544 [ 8.332427] remoteproc remoteproc1: remote processor b004000.rtu is now up [ 8.343654] net eth2: started [ 8.411291] remoteproc remoteproc8: powering up b234000.pru [ 8.417462] remoteproc remoteproc8: Booting fw image ti-pruss/am65x-pru0-prueth-fw.elf, size 16 468 [ 8.428986] remoteproc remoteproc8: remote processor b234000.pru is now up [ 8.437727] remoteproc remoteproc9: powering up b204000.rtu [ 8.445060] remoteproc remoteproc9: Booting fw image ti-pruss/am65x-rtu0-prueth-fw.elf, size 15 544 [ 8.456336] remoteproc remoteproc9: remote processor b204000.rtu is now up [ 8.467127] net eth4: started [ OK ] Found device /dev/mmcblk0p1. Starting File System Check on /dev/mmcblk0p1... [ OK ] Started File System Check on /dev/mmcblk0p1. Mounting /run/media/mmcblk0p1... [ OK ] Found device /dev/mmcblk1p1. [ OK ] Mounted /run/media/mmcblk0p1. Starting File System Check on /dev/mmcblk1p1... [ 9.369552] icssg-prueth pruss0_eth eth2: Link is Up - 1Gbps/Full - flow control rx/tx [ OK ] Started File System Check on /dev/mmcblk1p1. Mounting /run/media/mmcblk1p1... [ OK ] Mounted /run/media/mmcblk1p1. *************************************************************** *************************************************************** NOTICE: This file system contains the following GPLv3 packages: autoconf bash bc binutils cifs-utils cpio cpp-symlinks cpp dosfstools elfutils g++-symlinks g++ gawk gcc-symlinks gcc gdb gdbserver gettext glmark2 gstreamer1.0-libav gzip hidapi libbfd libdw1 libelf1 libgdbm-compat4 libgdbm6 libgettextlib libgettextsrc libgmp10 libidn2-0 libmpc3 libmpfr6 libreadline7 libunistring2 m4 make nettle parted pdm-anomaly-detection which If you do not wish to distribute GPLv3 components please remove the above packages prior to distribution. This can be done using the opkg remove command. i.e.: opkg remove Where is the name printed in the list above NOTE: If the package is a dependency of another package you will be notified of the dependent packages. You should use the --force-removal-of-dependent-packages option to also remove the dependent packages as well *************************************************************** *************************************************************** [ OK ] Started Print notice about GPLv3 packages. _____ _____ _ _ | _ |___ ___ ___ ___ | _ |___ ___ |_|___ ___| |_ | | _| .'| . | . | | __| _| . | | | -_| _| _| |__|__|_| |__,|_ |___| |__| |_| |___|_| |___|___|_| |___| |___| Arago Project http://arago-project.org am65xx-evm ttyS2 Arago 2019.11 am65xx-evm ttyS2 [ 13.092776] random: crng init done [ 13.096184] random: 7 urandom warning(s) missed due to ratelimiting am65xx-evm login: [ 316.536212] EXT4-fs (mmcblk1p2): error count since last fsck: 10 [ 316.542232] EXT4-fs (mmcblk1p2): initial error at time 1574562678: ext4_journal_check_start:61 [ 316.550859] EXT4-fs (mmcblk1p2): last error at time 1578743576: __ext4_get_inode_loc:4629: inod e 526400: block 2097285 [92574.840208] EXT4-fs (mmcblk1p2): error count since last fsck: 10 [92574.846233] EXT4-fs (mmcblk1p2): initial error at time 1574562678: ext4_journal_check_start:61 [92574.854843] EXT4-fs (mmcblk1p2): last error at time 1578743576: __ext4_get_inode_loc:4629: inod e 526400: block 2097285 root root@am65xx-evm:~# ifconfig eth3 eth3 Link encap:Ethernet HWaddr 70:FF:76:1D:4E:57 inet addr:192.168.100.230 Bcast:192.168.100.255 Mask:255.255.255.0 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) root@am65xx-evm:~# ethtool eth3 Settings for eth3: Supported ports: [ TP MII ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Half 1000baseT/Full Supported pause frame use: Symmetric Receive-only Supports auto-negotiation: Yes Supported FEC modes: Not reported Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Half 1000baseT/Full Advertised pause frame use: No Advertised auto-negotiation: Yes Advertised FEC modes: Not reported Speed: 10Mb/s Duplex: Half Port: MII PHYAD: 3 Transceiver: internal Auto-negotiation: on Current message level: 0x00007fff (32767) drv probe link timer ifdown ifup rx_err tx_err tx_queued intr tx_done rx_status pktdata hw wol Link detected: no root@am65xx-evm:~# ping 192.168.100.240 PING 192.168.100.240 (192.168.100.240): 56 data bytes ^C --- 192.168.100.240 ping statistics --- 14 packets transmitted, 0 packets received, 100% packet loss root@am65xx-evm:~#