TSC2102: Programming sequence

Kuramochi Tadahiko

Other Parts Discussed in Thread: TSC2102, TSC2000

Hi,

Is programming sequence of the TSC2102 apply the SLAA197?

If yes, it is described that "Tip 2: The initialization sequence shown in Figure 1 is needed ONLY once after each power up or reset." on the app note.

Isn't multiple reset as below allowed?

POWER UP　→　Initialize　→　RESET（All register clear）　→　Initialize（2nd）　→　RESET（All register clear）　→　初期化（3rd）　→　…

Best Regards,

Kuramochi

over 6 years ago

0 Kuramochi Tadahiko over 6 years ago

Guru 28715 points

Hi,
How is this progress?

Best Regards,
Kuramochi

0 Kuramochi Tadahiko over 6 years ago in reply to Kuramochi Tadahiko

Guru 28715 points

Is this forum appropriate?
If no, could anyone move it?
I could not select posting forum.

Best Regards,
Kuramochi

0 Collin Wells over 6 years ago in reply to Kuramochi Tadahiko

TI__Guru 63655 points

Hello Kuramochi,

This is the correct forum but please understand that these devices are in a limited support status. We will take a look and provide the best answer we can with the information we have available to us.

0 Kuramochi Tadahiko over 6 years ago in reply to Collin Wells

Guru 28715 points

Collin-san,

I got it.
I wait your answer.

Best Regards,
Kuramochi

0 Collin Wells over 6 years ago in reply to Kuramochi Tadahiko

TI__Guru 63655 points

Hello,

From what we've been able to determine, The TSC2102 was released after the devices that were part of the "First Generation of Smart Touch Controllers" Therefore, we do not believe the same restrictions apply to the TSC2102 that are described in the app note. However, if you'd like to be conservative you can utilize the same sequence for the TSC2102 that is described in the app note.

0 Kuramochi Tadahiko over 6 years ago in reply to Collin Wells

Guru 28715 points

Collin-san,

Thank you for your reply.

In the case of TSC2000/2200/2300, isn't multiple reset as below allowed?

POWER UP　→　Initialize　→　RESET（All register clear）　→　Initialize（2nd）　→　RESET（All register clear）　→　初期化（3rd）　→　…

Best Regards,

Kuramochi

0 Kuramochi Tadahiko over 6 years ago in reply to Kuramochi Tadahiko

Guru 28715 points

Collin-san,
How is this situation?
Best Reards,
Kuramochi

0 Collin Wells over 6 years ago in reply to Kuramochi Tadahiko

TI__Guru 63655 points

Hello Kuramochi-san,

I'm not sure I understand your question. If you're asking whether the product can be reset more than once after it's powered on, the answer is "Yes". You will need to initialize the device each time after reset.

0 Shota Mago over 6 years ago in reply to Collin Wells

TI__Expert 7990 points

Hi team,

I'm an analog FAE supporting a customer with Kuramochi-san in Japan.

Could someone reply on his latest question?
Since the customer has been waiting answer for this, quick reply is desirable.

I look forward to hearing back from you.

Best regards,
Shota Mago

0 Collin Wells over 6 years ago in reply to Shota Mago

TI__Guru 63655 points

Hello Mago-san,

I answered the question shortly before you posted. We were probably writing our messages at the same time :).

0 Shota Mago over 6 years ago in reply to Collin Wells

TI__Expert 7990 points

Hi Collin-san

I understood.
Thanks for supporting on this thread!

Best regards,
Shota Mago

The TI E2E™ design support forums will undergo maintenance from July 11 to July 13. If you need design support during this time, open a new support request with our customer support center.

Audio

Audio forum

TSC2102: Programming sequence