• State
  • Locked Locked
  • Replies 3 replies
  • Subscribers 82 subscribers
  • Views 147 views
  • Users 0 members are here
Support feedback
Options
Options
Similar topics

This thread has been locked.

If you have a related question, please click the "Ask a related question" button in the top right corner. The newly created question will be automatically linked to this question.

TMS320F280049: TMS320F280049

Saurabh Kumar
Prodigy 30 points
Part Number: TMS320F280049
Other Parts Discussed in Thread: XDS110ISO-EVM

Tool/software:

1) we have used a 14 pin 2.54mm pitch JTAG is used for MCU TMS320F280049CPZ (attached below image), and XDS110ISO-EVM Board J3 connector have 16 pins JTAG. It will be helpful if we get clarity on interfacing of JTAG with XDS.

2) TI MCU TMS320F280049CPZ ADC pin mapping is in below table. Need to confirm if pin is assigned to ADC correct ADC pin or Not?

MCU Pin No.

Pin Name

Net Name

23

A0_B15_C15_DACA_COUT

Total phase current PMSM sensing

10

A3

U phase current PMSM sensing

35

A5

V phase current PMSM sensing

38

A9

W phase current PMSM sensing

19

C0

Back EMF U phase PMSM motor sensing

29

C1

Back EMF V phase PMSM motor sensing

21

C2

Back EMF W phase PMSM motor sensing

41

B0

12V voltage sensing

40

B1_A10_C10_PGA7_OF

Temperature sensor_2 input

7

B2_C6_PGA3_OF

3V3 voltage sensing

8

B3_VDAC

5V voltage sensing

39

B4_C8_PGA4_OF

5V voltage sensing

17

C4

DC Input voltage sensing (36V/48V)

44

C14

Temperature sensor_1 input

  • 0
    TI__Mastermind 33116 points

    Hi, 

    Saurabh Kumar said:
    we have used a 14 pin 2.54mm pitch JTAG is used for MCU TMS320F280049CPZ (attached below image), and XDS110ISO-EVM Board J3 connector have 16 pins JTAG. It will be helpful if we get clarity on interfacing of JTAG with XDS.

    Is there a specific question you have about this? 

    Saurabh Kumar said:
    TI MCU TMS320F280049CPZ ADC pin mapping is in below table. Need to confirm if pin is assigned to ADC correct ADC pin or Not?

    Are you asking if your table matches the schematic?

    Thanks,

    Ben Collier

  • 0 in reply to Benjamin Collier
    Prodigy 30 points

    Hi Ben,

    1) For JTAG we want to sure 14 PIN connection is correct or not in schematics, any schematics change required?

    for programming and debugging this is connected to XDS110ISO-EVM J3 16 pin connector.  Any TI recommended adapter for connection.   

    2) We mapped ADC table to MCU ADC pin is corrected or not, because some ADC signals, we don't want to ADC MUX Pin (Bold Highlighted in table). These ADC signals are input independent ADC channels.

  • 0 in reply to Saurabh Kumar
    TI__Mastermind 33116 points

    Hi,

    Saurabh Kumar said:

    For JTAG we want to sure 14 PIN connection is correct or not in schematics, any schematics change required?

    for programming and debugging this is connected to XDS110ISO-EVM J3 16 pin connector.  Any TI recommended adapter for connection.   

    There should have been a converter for 14 pin header in the box, did you not receive it? 

    Saurabh Kumar said:
    We mapped ADC table to MCU ADC pin is corrected or not, because some ADC signals, we don't want to ADC MUX Pin (Bold Highlighted in table). These ADC signals are input independent ADC channels.

    I am still not sure that I understand your question. Do you want to use independent ADCs for your current phases? 

    Best Regards,

    Ben Collier