Search tips
Showing 16 results View by: Thread Post Sort by

  • ADC1175: Problem when unpluging the 5V supply

    TI Thinks Resolved
    Part Number: ADC1175 Hello all, To try to save energy, I turned off the 5V supply on the ADC1175. However, through the 3V3 input supply, the ADC was generating (I do not know how) 1.9V at the 5V power rail. This 1.9V would then feed the remaining circuits…

  • RE: ADC1175-50: Output voltage are random

    Hey Amr, As Chase said you're going to want to use a MOSFET to pull down through an LED. These output drivers are not designed to drive large resistive loads. Regards, Matt
    • Answered

  • TM4C1294KCPDT: When I use the EPI to read data from the adc1175, the chip becomes very hot，but the data is just correct ,is there something wrong in the epi config ?

    Resolved
    Part Number: TM4C1294KCPDT Other Parts Discussed in Thread: ADC1175 When I use epi0s0-s15 to read data from two adc1175s(8Bit adc), epi0s30 is configured as CS and it connects to the adcclk pin to provide clock to both adcs. I found that maybe the IO of…
    • Resolved

  • ADC1175: ADC1175 different part number

    TI Thinks Resolved
    Part Number: ADC1175 Other Parts Discussed in Thread: ADC1173 Hello, I have ADC1175 20 mhz, and i could not work properly Part number is exacly shown below National Semiconductor VM24ACE3 ADC1175 CIMTC Although i connected VRTS-VRT each other via 10uf…

  • ADC1175-50: TSSOP 14pin DVDD > AVDD ?

    TI Thinks Resolved
    Part Number: ADC1175-50 Hi The 14pin is described "DVDD" in datasheet /PIN DESCRIPTIONS AND EQUIVALENT CIRCUITS. The 14pin is AVDD in Other figures and EVM schematics. Is it typo? Thanks Muk

  • ADC1175: Jitter problem when sampling sinewave and squarewave

    TI Thinks Resolved
    Part Number: ADC1175 Hello, I have a project that continuously sampling ADC In pin on ADC1175 20Mhz but facing a lot of jitters on waveform. I thought problem may be regarding bare wire coming from microchip's clock and connecting ADC's clock pin. And…

  • ADC1175: What is dynamic capacitance what writes in datasheet and how to get over?

    TI Thinks Resolved
    Part Number: ADC1175 Hello, I am using adc1175 20 mhz and having spike issues on my measurements and i could not manage to remove it. ADC's Vin has spikes when i drive sine wave. When i use square wave spikes take place on rising edge on waveform.…
    • Answered

  • ADC1175-50: ADC1175-50CIMTX/NOPB with 3.3V digital interface

    Resolved
    Part Number: ADC1175-50 Other Parts Discussed in Thread: ADC1175 , SN74LVC8T245 , ADC1173 Dear Technical Support Team, I have a question about ADC1175-50CIMTX/NOPB. I'd like to use 3.3V digital interface with FPGA. Datasheet page.17 shows below…
    • Resolved
    • Answered

  • ADC1175: altough RT-RB delta 5 volts, after specific voltage, digital ports show very low voltage

    Resolved
    Part Number: ADC1175 Other Parts Discussed in Thread: ADS805 Hello, I have a project that I get adc1175-20 mhz measured continuously a specific signal. If voltage max value is in about RT-RB, for example 4,30 volts, suddenly digital ports begin to show…
    • Resolved

  • ADC1175: VRT and VRB values for conversion of video Signal

    TI Thinks Resolved
    Part Number: ADC1175 Other Parts Discussed in Thread: LMH6702 , Good Day, I am struggling with knowing what the optimum/proper values of VRT and VRB should be used if I am using the ADC1175 to digitize a video signal (15khz 240x320). A typical video signal…

Didn't find what you are looking for? Post a new question.