TI E2E support forums
TI E2E support forums
  • User
  • Site
  • Search
  • User
  • E2E™ design support >
  • Forums
    • Amplifiers
    • API solutions
    • Audio
    • Clock & timing
    • Data converters
    • DLP® products
    • Interface
    • Isolation
    • Logic
    • Microcontrollers
    • Motor drivers
    • Power management
    • Processors
    • RF & microwave
    • Sensors
    • Site support
    • Switches & multiplexers
    • Tools
    • Wireless connectivity
    • Archived forums
    • Archived groups
  • Technical articles
  • TI training
    • Tech days
    • Online training
    • Live events
    • Power Supply Design Seminar
  • Getting started
  • 简体中文
  • More
  • Cancel


Search tips
Showing 36 results View by: Thread Post Sort by
  • ADS1211: ADS1210

    Robert Pettersson
    Robert Pettersson
    Part Number: ADS1211 Other Parts Discussed in Thread: ADS127L11 Hi, I'm interested to hear what TI recommend as replacement for ADS1210? I have seen the Obsolete PCN for the ADS1210(TI Number PDN# 20220830000.3) and the two recommended parts there…
    • over 1 year ago
    • Data converters
    • Data converters forum
  • ADS1211: Lifecycle risk

    Søren Nielsen
    Søren Nielsen
    TI Thinks Resolved
    Part Number: ADS1211 We are using the ADS1210, and last spring it was active, but it became obsolete with a relative short last time buy period. The datasheet for ADS1210 also specifying the ADS1211. It seems like only footprint is necessary to change…
    • over 2 years ago
    • Data converters
    • Data converters forum
  • ADS1211: About MUX inside the device

    Yuto Sakai
    Yuto Sakai
    TI Thinks Resolved
    Part Number: ADS1211 Other Parts Discussed in Thread: ADS1261 , ADS124S08 Hi, Could you tell me about the internal schematic of the device. Is there information on the MUX equivalent schematic? Best regards, Yuto Sakai
    • over 5 years ago
    • Data converters
    • Data converters forum
  • ADS1211: ADS1211E

    JAYARAMULU T
    JAYARAMULU T
    TI Thinks Resolved
    Part Number: ADS1211 Hi...... I am interfacing ADS1211E through SPI with PSOC5 in my Project.I am able to write the data to ADS1211 but I am not able to Read the data from ADS1211E.. I was trying to write data to command register using instruction register…
    • over 7 years ago
    • Data converters
    • Data converters forum
  • Answered
  • ADS1211: Validate an approved fab lot from marking code

    Pascal Routhier
    Pascal Routhier
    Resolved
    Part Number: ADS1211 Other Parts Discussed in Thread: ADS124S08 , ADS1256 , ADS1262 , INA188 Hi, may you please help to confirm good/approved fab lots from marking code on ADS1211U devices we got? Picture of the device and info provided further down. We…
    • Resolved
    • over 8 years ago
    • Data converters
    • Data converters forum
  • Answered
  • Reset for ADS1211

    ttd
    ttd
    Resolved
    Other Parts Discussed in Thread: ADS1211 Dear Technical Support Team I have a question about ADS1211. Is it better to issue reset sequence of "FIGURE 27. Resetting the ADS1210/11" every power up? Datasheet shows " If the power supply ramp…
    • Resolved
    • over 8 years ago
    • Data converters
    • Data converters forum
  • RE: ADS1211 reaDING PROBLEM

    Bob Benjamin
    Bob Benjamin
    Hi Arti, You really haven't given me much information and I'm not there to observe your setup (see my previous post for requested information). It is like calling a doctor and saying 'I don't feel well, what is wrong?' I suspect that…
    • over 9 years ago
    • Data converters
    • Data converters forum
  • INTERFACING BETWEEN PIC16F876 WITH ADS1211 READING PROBLEM using SPI

    arti mishra
    arti mishra
    Other Parts Discussed in Thread: ADS1211 DEAR SIR, kindly help me out in below code ,I don't known what is wrong in this, iam not able to read from DOR register: void main(void) { unsigned int i,c; TRISA=0x00; // mux selection A,B,C output=0,STARt…
    • over 9 years ago
    • Interface
    • Interface forum
  • Answered
  • RE: ADS1211 Communication

    Philip Nielsen86244
    Philip Nielsen86244
    Resolved
    Other Parts Discussed in Thread: ADS1211 I was able to purhase 28 pin PDIP ADS1211 IC's. I am using the Cypress MCU family for interface. Sorry it is not a TI. Anyway I saw some code on the forum forcalibration. Is there any code for a the actual reading…
    • Resolved
    • over 12 years ago
    • Data converters
    • Data converters forum
  • RE: Re: ADS1211 Example Code

    Bob Benjamin
    Bob Benjamin
    Philip, Selecting an ADC can be about resolution, and we have a lot of 24-bit ADCs, but there are usually other criteria that is important. Does the input need gain? What is the input range? How fast do you need to collect the data? How many input channels…
    • over 12 years ago
    • Data converters
    • Data converters forum
>

Didn't find what you are looking for? Post a new question.

  • Ask a new question