• ADS9234R: Is it suitable solution to replace LTC1407AIMSE-1#PBF?

  

  Jimmy WANG

  TI Thinks Resolved

  Part Number: ADS9234R Other Parts Discussed in Thread: ADS7057 Hi team, May I use ADS9234R to replace LTC1407AIMSE-1#PBF? But I think pin/out is too much. Do you have a better solution? thanks

  • over 2 years ago
  • Data converters
  • Data converters forum

• ADS9234R: Request of C Drivers for AD9234R

  

  NIDADAVOLU RAGHAVENDRA RAVI KUMAR

  TI Thinks Resolved

  Part Number: ADS9234R Please provide C Drivers for AD9234R

  • over 3 years ago
  • Data converters
  • Data converters forum

• ADS9234R: Is there digital interface model for ADS9234R??

  

  Ssu-Han Huang

  TI Thinks Resolved

  Part Number: ADS9234R Other Parts Discussed in Thread: ADS9224R , ADS9224REVM-PDK Hi, I am going to use FPGA to control ADS9234. Do you provide the digital interface model that I can run my simulation first? Thanks

  • over 5 years ago
  • Data converters
  • Data converters forum

• ADS9234R: ADS9234R

  

  Naizeng Wang

  TI Thinks Resolved

  Part Number: ADS9234R Other Parts Discussed in Thread: ADS9224R What’s the difference between enhanced-SPI and SPI? In addition, is there some special requirements for the MCU?

  • over 6 years ago
  • Data converters
  • Data converters forum
Answered

• ADS9234R: Question for SPI communication

  

  Kazuki Kuramochi

  Resolved

  Part Number: ADS9234R Hello Expert, I have question for ADS9234R regarding SPI communication. We configured SPI communication lane between this device and HOST side as below figure which is referred datasheet 7.6.2.2.2 . Then, I'd like to know about whether…

  • Resolved

  • over 4 years ago
  • Data converters
  • Data converters forum

• ADS9234R: SPI configuration with shared nCS and CONVST

  

  Alexander Drexel

  TI Thinks Resolved

  Part Number: ADS9234R Hi, I have a question about the pin configuration where nCS is tied to CONVST as shown in Figure 67 on p. 40 of the datasheet. How is the device configuration handled in this case because it's not possible to keep CONVST high during…

  • over 4 years ago
  • Data converters
  • Data converters forum
Answered

• ADS9234R: SCLK launch edge to next data valid on SDO delay

  

  Erickson Ramos

  Resolved

  Part Number: ADS9234R Hi, The ADS9234R datasheet specifies the maximum delay time from SCLK launch edge to next data valid on SDO (td-ckdo 15.8ns for SDR). What is the minimum time delay? If we plan to read SDO pin immediately after SCLK launch edge…

  • Resolved

  • over 4 years ago
  • Data converters
  • Data converters forum
Answered

• RE: ADS9234R: Sending Sampling Data over one SDO wire

  

  Ryan Andrews

  Resolved

  Hello Ralf, Thank you for your post and welcome to our forum! Unfortunately, what you are describing is not possible with this device. The Legacy SPI mode outputs ADC_A data on SDO_A and ADC_B data on SDO_B only. In other words, at least one SDO pin…

  • over 6 years ago
  • Data converters
  • Data converters forum
Answered

• AM2434: Sinus Cosing resolver with AM243 ADC

  

  Jan Bock

  Resolved

  Part Number: AM2434 Other Parts Discussed in Thread: ADS9234R , ADS7253 , ADS7251 Tool/software: A question about the ADC of the AM243x: We would like to use a SinCos resolver. We assume: MaxRPM= 9000Rpm -> 150 revolutions / s Number of lines of…

  • Resolved

  • over 1 year ago
  • Arm-based microcontrollers
  • Arm-based microcontrollers forum
Answered

• ADS7253: >1MSPS, 4ch/8ch simultaneous-sampling ADC

  

  Hollis Liu

  Resolved

  Part Number: ADS7253 Other Parts Discussed in Thread: ADS9234R HI Team, Do we have 4ch/8ch simultaneous sampling ADC(>1MSPS)? I see the ADS7253 only have dual simultaneous sampling. But we need more simultaneous sampling channels. Thanks.

  • Resolved

  • over 4 years ago
  • Data converters
  • Data converters forum

Didn't find what you are looking for? Post a new question.