• AM26C31: AM26C31 PCN issue

  

  Eddie Chou

  Part Number: AM26C31 Other Parts Discussed in Thread: SN75ALS192 Tool/software: Hi Team, Customer use AM26C31 for long time and happened high defect rate after our PCN change, https://mm.digikey.com/Volume0/opasdata/d220001/medias/docus/6146/PCN20240328001…

  • 3 months ago
  • Interface
  • Interface forum

• AM26C31: AM26C31

  

  WILSON SHEN

  TI Thinks Resolved

  Part Number: AM26C31 Tool/software: Hi TI team： We have used the AM26C31 in the Motor control situation，have some issues as below 1.I got a RMA issue，we have found that Voh only 1.6V （spec shows need more than 2.4V@20mA），we have check the output current…

  • 9 months ago
  • Interface
  • Interface forum
Answered

• AM26C31: Absolute Maximum Ratings of AM26C31 / AM26LS31 Output Pins

  

  Conor

  Resolved

  Part Number: AM26C31 Other Parts Discussed in Thread: AM26LS31 Tool/software: Hi, We are investigating the differences between AM26C31 and AM26LS31 and would like to confirm the following points regarding their output pin absolute maximum ratings. …

  • Resolved

  • 6 months ago
  • Interface
  • Interface forum
Answered

• AM26C31: AM26C31 max signaling rate

  

  Jenny Li

  Resolved

  Part Number: AM26C31 Other Parts Discussed in Thread: SN65LBC174A , SN65LBC175A , THVD1450 , THVD1550 Tool/software: Hi, Please see link https://www.ti.com/product/AM26C31 . We are looking for a differential line driver for 20MHz clock signal and want…

  • Resolved

  • 8 months ago
  • Interface
  • Interface forum

• AM26C31: Inquiry regarding the package marking of the AM26C31 series

  

  HC Kim

  Part Number: AM26C31 Tool/software: Hi all, I would like to inquire about the package marking as stated in the subject. I purchased products under three different temperature conditions from the open market(mouser). The familiar marking can only…

  • 8 months ago
  • Interface
  • Interface forum

• AM26C31: output distortion

  

  Gary Zeng

  TI Thinks Resolved

  Part Number: AM26C31 Other Parts Discussed in Thread: TVS0701 , TSD12C Tool/software: Hi team, My customer uses a lots of AM26C31IDR in Servo and VFD products. Now they met a output waveform distortion issue of AM26C31 in servo products, which is…

  • 1 month ago
  • Interface
  • Interface forum

• AM26C31: Inquiry Regarding AM26C31IDR Connection Modification

  

  Takashi Matsumura

  TI Thinks Resolved

  Part Number: AM26C31 Tool/software: Dear TI Team, Thank you for your support. We would like to modify the connection of the AM26C31IDR as shown in the attached document. Could you please advise whether leaving the inverted output pins open would…

  • 1 month ago
  • Interface
  • Interface forum

• AM26C31: No load voltage variation

  

  anson zhou

  TI Thinks Resolved

  Part Number: AM26C31 Tool/software: Hi Sir : The output signal level amplitude of the 2025 version of chip AM26C31 reaches 4.95V under no-load, while the previous version had an amplitude of 4.2V-4.4V. May I ask where the change was caused?

  • 3 months ago
  • Interface
  • Interface forum
Answered

• AM26C31: AM26C31IDR Comparison between SFAB and RFAB materials

  

  Freddy Hsieh

  Resolved

  Part Number: AM26C31 Tool/software: Hi team, Please provide a comparison table for AM26C31IDR between SFAB and RFAB materials. Thank you.

  • Resolved

  • 1 month ago
  • Interface
  • Interface forum

• AM26C31: 2ch Solution

  

  Brian Wang0928

  TI Thinks Resolved

  Part Number: AM26C31 Other Parts Discussed in Thread: SN75ALS191 , THVD1420 , THVD1400 Tool/software: AM26C31 is a 4ch. Is there 2ch solution with similar function since pcb size is a constrain in customer side. The VCC is 5V. Regards Brian

  • 3 months ago
  • Interface
  • Interface forum

Didn't find what you are looking for? Post a new question.