Answered

• AM26LS32AC: Operation with only single ended PWM

  

  Thomas Heilmeier

  Resolved

  Part Number: AM26LS32AC Other Parts Discussed in Thread: AM26C32 Hello, I have a question regarding the AM26LS32AC. What happens if I only put a single ended PWM at PIN 1A, 2A, 3A and leave the PIN 1B, 2B and 3B open? I didn't find the information in…

  • Resolved

  • over 3 years ago
  • Interface
  • Interface forum
Answered

• AM26LS32AC: The fail-safe does not work on some of my boards.

  

  Charles Kaseff

  Resolved

  Part Number: AM26LS32AC Other Parts Discussed in Thread: SN65LBC173A , AM26LV32 , SN75LBC173A I am using an AM26LS32ACPWR. There is a 100-ohm termination resistor between the A and B inputs. When these inputs are floating, I expect to see a high on the…

  • Resolved

  • over 3 years ago
  • Interface
  • Interface forum

• AM26LS32AC: IC pulling LDO and Buck ouptput to a lower voltage causing drop in 5V line

  

  Amrith H

  TI Thinks Resolved

  Part Number: AM26LS32AC Other Parts Discussed in Thread: DRV8323 , , AM26C32 , AM26LV32 Hi, We are using Buck out from drv8323 SPI variant , the voltage from Buck is designed to be around 7V which is given to 3.3V and 5V LDOs . The IC AM26LS32AC is…

  • over 3 years ago
  • Interface
  • Interface forum

• AM26LS32AC: AM26LS32AC Termination and Pull-up

  

  Franz Figueroa32

  TI Thinks Resolved

  Part Number: AM26LS32AC Hi E2E, Good day! A customer of mine would like to know the following: 1) Is the termination resistor is required, as section 9.2 discussed that this device might be possible to work even without termination. 2) Pull-up…

  • over 6 years ago
  • Interface
  • Interface forum

• AM26LS32AC: noise problem

  

  Davoud Karimi

  TI Thinks Resolved

  Part Number: AM26LS32AC Hi, I am using AM26LS32ACN IC to interface an encoder signal and pass it to a counter. The motion section of the board works fine, which means that the IC is working perfectly. However, in another section of the board I am…

  • over 5 years ago
  • Interface
  • Interface forum

• AM26LS32AC: AM26LS32AC

  

  somnath barge

  TI Thinks Resolved

  Part Number: AM26LS32AC Hi, I am using AM26LS32AC for encoder interfacing. I am using 100 ohm resistor for termination. But sometimes I didn't get output from chip. This problem resolved with multiple solution. They are as follows - 1 . If I change…

  • over 8 years ago
  • Interface
  • Interface forum
Answered

• AM26LS32AC: Replacement for AM26LS32ACM

  

  Li Chen92

  Resolved

  Part Number: AM26LS32AC Other Parts Discussed in Thread: AM26C32 Hi TI expert Does TI has any products replacement for DS26LS32ACM? Best regards. Thomas

  • Resolved

  • over 6 years ago
  • Interface
  • Interface forum
Answered

• AM26LS32AC: Junction temperature

  

  Motoyasu Hattori

  Resolved

  Part Number: AM26LS32AC Other Parts Discussed in Thread: AM26LS32A Hi, On the datasheet, only Ta is defined on AM26LS32 devices. Could you please let us know the Tj value? Thanks and best regards, M.HATTORI.

  • Resolved

  • over 6 years ago
  • Interface
  • Interface forum

• AM26LS32AC: Input Signal during power off

  

  Mark Philip Felipe

  TI Thinks Resolved

  Part Number: AM26LS32AC Hi Team, We would like to confirm if an input signal is driven on the unpowered device. Would there be direct damage or the device would not just function since it is not on? The reason behind this is that there is a possible…

  • over 6 years ago
  • Interface
  • Interface forum

• AM26LS32AC: Converts the differential signal to a different logic state or not

  

  Danilo A.

  Part Number: AM26LS32AC Hi Team, Table 1 of Section 8.4 Device Functional Modes shows the output Y of AM26LS32AC when VIT– ≤ VID ≤ VIT+ is indeterminate. A customer would like to know whether the device converts the differential signal to a different…

  • over 5 years ago
  • Interface
  • Interface forum

Didn't find what you are looking for? Post a new question.