• AM26LV31E-EP: Rs422 signal driver AM26LV31E-EP unused input pin connection

  

  Rohit Bhayal

  TI Thinks Resolved

  Part Number: AM26LV31E-EP Tool/software: Hii, For the AM26LV31ESDREP IC, if certain drivers are not in use, where should the unused input pins be connected? Should they be grounded or connected to VCC?

  • 24 days ago
  • Interface
  • Interface forum
Answered

• AM26LV31: recommended replacements

  

  Fukushima Motohiko

  Resolved

  Part Number: AM26LV31 Other Parts Discussed in Thread: AM26LV32E , Tool/software: Thank you for your help. Please let me know the recommended replacements for the following: 1.AM26LV31CNS 2.AM26LV32CNS Thank you in advance.

  • Resolved

  • 1 month ago
  • Interface
  • Interface forum

• AM26LV31: Polarity correction on IC?

  

  Jesse Cazun

  Part Number: AM26LV31 Other Parts Discussed in Thread: THVD1505 , SN65HVD888 Tool/software: Hello all, We replaced some DS26LV31TM's with AM26LV31C's expecting a direct replacement. After doing the change, it seems like we are getting reversed polarity…

  • 1 month ago
  • Interface
  • Interface forum

• AM26LV31E: Unexpected Output with A low, and Y going high

  

  Daniel Mahoney

  Part Number: AM26LV31E Tool/software: I am using an AM26LV31E. Specifically AM26LV31EIRGYR. I ground both G and G not. Based on the datasheet truth table, When pin 12 (G not) is driven low, pin 4(G) becomes a don't care. To me this configuration…

  • 2 months ago
  • Interface
  • Interface forum
Answered

• AM26LV31E: RS422 Evaluation Board (7 Tx, 1 Rx)

  

  JT Miller

  Resolved

  Part Number: AM26LV31E Other Parts Discussed in Thread: THVD1420 Tool/software: I have a breadboard application where I need to drive 7 RS422 output, and receive 1 RS422 input. These will interface with an FPGA, so I'd like to use 3.3V logic. The interface…

  • Resolved

  • 5 months ago
  • Interface
  • Interface forum

• AM26LV31: about VOD

  

  ? ?

  TI Thinks Resolved

  Part Number: AM26LV31 Hello, may I ask a question about AM26LV31. My backend servo control differential input requires a VT value between 2.5-3.8V, 1) May I ask if the differential output voltage of this chip can meet the requirements. I have confirmed…

  • 7 months ago
  • Interface
  • Interface forum

• AM26LV31E: Is it suitable for converting photodiode single-ended signal into differential signal?

  

  Ven Hsu

  TI Thinks Resolved

  Part Number: AM26LV31E Other Parts Discussed in Thread: AFE4400 , Tool/software: Since our photodiode is in a single-ended input configuration, would the AM26LV31E be suitable for converting the photodiode into a differential signal to serve as the input…

  • 5 months ago
  • Interface
  • Interface forum
Answered

• AM26LV32E: supply voltage of AM26LV32E and AM26LV31E

  

  kenji.kodama

  Resolved

  Part Number: AM26LV32E Other Parts Discussed in Thread: AM26C31 , AM26C32 Can the power supply voltage of AM26LV32EIRGYR and AM26LV31EIRGYR be used at 5V?

  • Resolved

  • 9 months ago
  • Interface
  • Interface forum
Answered

• AM26LV31: AM26LV31 & AM26LV32

  

  Axel Liot

  Resolved

  Part Number: AM26LV31 Other Parts Discussed in Thread: AM26LV32 , Hi ! I would like to know, because I didn't find the info in the DS (maybe I did'nt read it right), what's the max consumption of the AM26LV31 and the AM26LV32 at 3.3Vcc ? Thanks…

  • Resolved

  • over 1 year ago
  • Interface
  • Interface forum
Answered

• AM26LV31E: AM26LV31E IO pins

  

  Nachiketh Karanth

  Resolved

  Part Number: AM26LV31E Hi, I am using the part AM26LV31ESDREP. 1. Can we leave the input/output pins floating? Regards, Nachiketh

  • Resolved

  • over 1 year ago
  • Interface
  • Interface forum

Didn't find what you are looking for? Post a new question.