• BQ27532-G1: Can bq24253 work with bq27532-g1?

  

  Nathan Wineera

  TI Thinks Resolved

  Part Number: BQ27532-G1 Other Parts Discussed in Thread: BQ24253 , Can bq24253 work with bq27532-g1? In the datasheet of bq27532-g1 it mentions it can work with bq2425x. But how to work with bq24253 when bq24253 has no I2C interface and is fully stand…

  • 1 month ago
  • Power management
  • Power management forum
Answered

• BQ24253: Fast charging current different to ISET

  

  Groupe-HW

  Resolved

  Part Number: BQ24253 Tool/software: Hello, The fast charging current is set to about 1A using the RSET resistor set to 237 ohm. We measured the maximum charge current to 500/600mA. ILIM is set to 2A by connecting ILIM to ground. EN1 and EN2 are…

  • Resolved

  • over 2 years ago
  • Power management
  • Power management forum
Answered

• BQ25616: Changing from bq24253

  

  Dice-K

  Resolved

  Part Number: BQ25616 Other Parts Discussed in Thread: BQ24253 Hi support team, Three questions when changing from bq24253 to bq25616. (1) Although bq24253 has been operated with EN1/2, does bq25616 automatically start charging after detecting power…

  • Resolved

  • over 2 years ago
  • Power management
  • Power management forum
Answered

• BQ24253: BQ24253 doesnt enter into battery charging mode

  

  yagnik pokal

  Resolved

  Part Number: BQ24253 BQ24253 doesnt enter into battery charging mode I have used the TS Voltage is 2.44V Charge enable pin low EN1 = High EN2 = Low ILIMIT = 0E ISET = 250 E Bat capacity 3000 mA Li-ion chemistry D+/D- connected Still…

  • Resolved

  • over 3 years ago
  • Power management
  • Power management forum
Answered

• BQ24253: Charger behavior if TS is left open

  

  TISL

  Resolved

  Part Number: BQ24253 Tool/software: Dear e2e Support, Could you clarify how the charger react in case of the TS pin is disconnected? TS_STAT moved to '111', but does it stop the charge? Regards,

  • Resolved

  • over 2 years ago
  • Power management
  • Power management forum
Answered

• ESD441: ESD protection for BQ24253

  

  DDdoor

  Resolved

  Part Number: ESD441 Other Parts Discussed in Thread: BQ24253 Hello, The type-C (usb2.0) VBUS has a 5V input. And it is connected to BQ24253. In this case, what ESD protection device should I choose? Best regards, DDdoor

  • Resolved

  • over 2 years ago
  • Interface
  • Interface forum
Answered

• BQ24253: How to use the D± pin

  

  Dice-K

  Resolved

  Part Number: BQ24253 Other Parts Discussed in Thread: BQ25616 Hi support team, I have two questions about the D± pins. bq24253_D-pin.pdf Regards, Dice-K

  • Resolved

  • over 2 years ago
  • Power management
  • Power management forum

• BQ24253: Standalone type charger IC recommendation

  

  JH Shin

  TI Thinks Resolved

  Part Number: BQ24253 Other Parts Discussed in Thread: BQ25616 Hello, My customer is looking for a standalone type charger IC to replace the LowPowerSemi LP4032. Among the TI Charger ICs, please recommend a low-cost product that supports the following…

  • over 2 years ago
  • Power management
  • Power management forum

• BQ24253: BQ24253

  

  Jamie Tseng

  TI Thinks Resolved

  Part Number: BQ24253 Other Parts Discussed in Thread: BQ25616 Hi Team, Because our battery capacity is very large, there is a chance to exceed 12Hr, how to set up in Stand Along version? Or do you have any similar similar solution that can support…

  • over 6 years ago
  • Power management
  • Power management forum

• BQ24253: Reason for not D+ and D- detection

  

  Satoshi

  TI Thinks Resolved

  Part Number: BQ24253 Other Parts Discussed in Thread: BQ25616 , , BQ24251 One customer is considering bq25243, USB Type-C and Li-Ion battery. When both USB and Battery connecting, /PG was not assert Low and charge current become about 100mA in any…

  • over 3 years ago
  • Power management
  • Power management forum

Didn't find what you are looking for? Post a new question.