• BQ35100EVM-795: "The detected device is not compatible with this application": Troubles with using BQ35100EM-795 Eval Board and 3.6 Li-SOCl2 battery

  

  Vladimir Zitoli

  Part Number: BQ35100EVM-795 Other Parts Discussed in Thread: BQSTUDIO , EV2400 Dear all, I bought the BQ35100EVM-795 EvalBoard but I have had some troubles during its use. As a matter of fact, once I have prepared the setup as shown on the User…

  • over 1 year ago
  • Power management
  • Power management forum

• RE: Gauge for alkaline battery and coin cell batterie

  

  -Terry

  Hi Omar, We have a gauge for primary cells (bq35100 - www.ti.com/.../BQ35100) , but this is targeted primarily at Lithium primary cells (LiMnO2, LiSOCl2), not alkaline. Thanks, Terry

  • over 8 years ago
  • Power management
  • Power management forum
Answered

• BQ35100EVM-795: Unable to read updated voltage values without cycling power

  

  Sarika K

  Resolved

  Part Number: BQ35100EVM-795 Other Parts Discussed in Thread: BQ35100 , MSP430FR5994 , BQSTUDIO , EV2400 I am using an MSP430FR5994 to read the voltage supplied to the BQ35100 via I2C using the command 0x08, as seen in the code below. The issue I am running…

  • Resolved

  • over 1 year ago
  • Power management
  • Power management forum

• BQ35100EVM-795: USB interfacing

  

  Julien LAFFITTE

  TI Thinks Resolved

  Part Number: BQ35100EVM-795 Other Parts Discussed in Thread: TMP117EVM , BQSTUDIO , EV2400 , BQ35100 Hi, I have see the BQ35100EVM dev board. We can be interested in it for test the IC. We have a TMP117EVM board, i have see it have the same microntroler…

  • over 4 years ago
  • Power management
  • Power management forum

• RE: Protection for Lithium battery

  

  Onyx Ahiakwo

  Hi Vikas, yes, that is the typical batteries used for such products. Have you looked at our bq35100 battery gauging for those type of batteries? For battery protection, you should consider the bq297x family of devices. thanks Onyx

  • over 7 years ago
  • Power management
  • Power management forum
Answered

• BQ35100EVM-795: Unable to unseal the device and use coulomb counter function

  

  Matthew Izard

  Resolved

  Part Number: BQ35100EVM-795 Other Parts Discussed in Thread: EV2400 , BQSTUDIO Hello everyone, I am a definite newby to working with gas gauges and evaluation modules. I am working with the BQ35100EVM and am having a lot of problems with where to…

  • Resolved

  • over 3 years ago
  • Power management
  • Power management forum

• RE: TCA9554A: TCA9554A tsp Timing fail

  

  Jay zhu

  BOBBY said: If we want to be specific here, the master is required to hold the dataline low for 300ns based on the denotation [3] of table 10 on page 48 of the I2C spec V2.6 "A device must internally provide a hold time of at least 300 ns for the…

  • over 5 years ago
  • Interface
  • Interface forum

• RE: Battery voltage/current measurement - Coin cell

  

  -Terry

  You might consider the bq35100, which will release to production soon. You can see more information at www.ti.com/.../BQ35100 Thanks, Terry

  • over 9 years ago
  • Power management
  • Power management forum
Answered

• BQ35100EVM-795: How to write to data flash

  

  Buff Thokoa

  Resolved

  Part Number: BQ35100EVM-795 Other Parts Discussed in Thread: BQ35100 , EV2400 , BQSTUDIO Hi, I am trying to configure the data flash parameters using the Advanced comm section of the GUI. I have the device in accumulation mode and unseal full access…

  • Resolved

  • over 4 years ago
  • Power management
  • Power management forum

• RE: Fuel gauge for Lithium chloride battery

  

  Fernando Lopez

  Hello David, Please review the available information for the bq35100 which is a lithium primary gauge. Please note the device is still in preview. www.ti.com/.../bq35100

  • over 9 years ago
  • Power management
  • Power management forum

Didn't find what you are looking for? Post a new question.