TI E2E support forums
TI E2E support forums
  • User
  • Site
  • Search
  • User
  • E2E™ design support >
  • Forums
    • Amplifiers
    • API solutions
    • Audio
    • Clock & timing
    • Data converters
    • DLP® products
    • Interface
    • Isolation
    • Logic
    • Microcontrollers
    • Motor drivers
    • Power management
    • Processors
    • RF & microwave
    • Sensors
    • Site support
    • Switches & multiplexers
    • Tools
    • Wireless connectivity
    • Archived forums
    • Archived groups
  • Technical articles
  • TI training
    • Tech days
    • Online training
    • Live events
    • Power Supply Design Seminar
  • Getting started
  • 简体中文
  • More
  • Cancel


Search tips
Showing 24 results View by: Thread Post Sort by
    Answered
  • CSD16301Q2: Please help me choose a N-Channel Mosfet

    user5811580
    user5811580
    Resolved
    Part Number: CSD16301Q2 Other Parts Discussed in Thread: CSD17381F4 , LMG1020 Just have a look at the picture attached as below. I want to find a suitable N-channel mosfet as the driver of the LD. According to the SPEC, the MAX voltage of this LD…
    • Resolved
    • over 4 years ago
    • Power management
    • Power management forum
  • RE: CSD17318Q2: CSD17318Q2

    John Wallace1
    John Wallace1
    Hi Murthy, Thanks for the update. Can you share your schematic with me? If you do not want to share it on this public forum, please send me a friend request and as soon as I accept it, you can share the schematic in a private message. Can you tell…
    • over 5 years ago
    • Power management
    • Power management forum
  • BQ78350-R1A: Unable to change BQ78350-R1A Cell Map to five cells and not initializing

    Maclean Ross-Howe
    Maclean Ross-Howe
    Part Number: BQ78350-R1A Hello, I am trying to make a five cell bms with the BQ78350-R1A and BQ7920 and a rasberry Pi 4. We have communication between the Pi and the BMS through SMBus but we are only able to read 3 of the five cell voltages. Any attempt…
    • 1 month ago
    • Power management
    • Power management forum
  • RE: LM5112: Fast mos driver (LM5112) + fast mos (suggestion?) for a pulsed led driver

    Jeffrey Mueller
    Jeffrey Mueller
    Hi Fulvio, what end equipment will this be in? if the size is constrained we recommend the following FETs: For GaN, you dont need a high voltage GaN so theres a limited selection since GaN has a intrinsically higher breakdown voltage. EPC2040 and…
    • over 7 years ago
    • Power management
    • Power management forum
  • Answered
  • BQ2970: Li-pol protection circuit

    Nick 199
    Nick 199
    Resolved
    Part Number: BQ2970 Other Parts Discussed in Thread: CSD17381F4 Hello! I'm designing one cell Li-pol protection circuit based on BQ29707 IC. The schematic is similar to the datasheet example: I need to limit currents of approximately 500 mA. So…
    • Resolved
    • over 7 years ago
    • Power management
    • Power management forum
  • Answered
  • RE: BQ27742-G1: reverse current protection

    Phil Yi
    Phil Yi
    Resolved
    Please find the circuit attached and TI N-CH MOSFET CSD17381F4 is a good part for that. Thanks! Phil
    • over 8 years ago
    • Power management
    • Power management forum
  • RE: TXS0102: Partial power off and voltage levels

    Stephen Fenwick
    Stephen Fenwick
    The discharge FET is a CSD17381F4, so it can handle a lot more current; the size of the dropping resistor might get too high. Is there an app note about using Ioff with the TXS parts? There seem to be conditions not documented in the datasheet. The…
    • over 7 years ago
    • Logic
    • Logic forum
  • RE: LM5134: PILOT MOSFET Selection

    Richard Herring
    Richard Herring
    Hello Ras, Thank you for considering the LM5134 in your design. I am an application engineer supporting this device and I will address your questions. Since the PILOT FET can be low voltage such as 20V, the gate charge can be very low and still have…
    • over 8 years ago
    • Power management
    • Power management forum
  • RE: CSD25481F4

    Brett Barr1
    Brett Barr1
    Eli, See the reliability data below. I the the FIT rate and MTBF numbers should answer your question. Granted this is for the CSD17381F4 but all FemtoFET data should be the same.
    • over 12 years ago
    • Power management
    • Power management forum
  • Answered
  • CSD17484F4: Material content

    Yixin Ma
    Yixin Ma
    Resolved
    Part Number: CSD17484F4 Other Parts Discussed in Thread: CSD17483F4 , CSD17381F4 Hi TI experts, May I have the material content sheet of the CSD17484F4? I didn't see the result using the material content searching tools. I want to make sure it's non…
    • Resolved
    • over 5 years ago
    • Power management
    • Power management forum
<>

Didn't find what you are looking for? Post a new question.

  • Ask a new question