The TI E2E™ design support forums will undergo maintenance from July 11 to July 13. If you need design support during this time, open a new support request with our customer support center.



Search tips
Showing 26,888 results View by: Thread Post Sort by

  • USB-PD-CHG-EVM-01: USB-PD-CHG-EVM-0

    TI Thinks Resolved
    Part Number: USB-PD-CHG-EVM-01 Other Parts Discussed in Thread: BQ25750 , BQ25798 Tool/software: I would like to use the USB-PD-CHG-EVM-01 in a test application for testing mobile charging bricks and other charging devices. I was wondering if the USB-PD…

  • TDA4VM: TDA4VM - EVM could not boot when connect to DISPLAYPORT 0 (PSDKL/PSDKR version - 09.01.00.06)

    TI Thinks Resolved
    Part Number: TDA4VM Hi, I have recently bought TDA4VM Evaluation Boards ( J721EXCP01EVM + J721EXSOMG01EVM). I have downloaded PSDK Linux and PSDK RTOS version 09.01.00.06. I followed the instructions to setup and compile the vision apps, then copy them into…

  • PROCESSOR-SDK-J721E: Does PCIe slot 0 work on J721e EVM?

    Part Number: PROCESSOR-SDK-J721E Other Parts Discussed in Thread: TDA4VM , J784S4XEVM Hi, I have got a PCIe driver working under FreeRTOS on TDA4AH. However it is only properly working for the PCIe cable connected in slot 1. When I try slot 0, it succeeds…
    • Answered

  • Run ums 0 mmc 0 will be stuck in uboot at J784S4 EVM

    Resolved
    Other Parts Discussed in Thread: TDA4VM J784S4 Hi I am using SDK8.2.2 at J784S4 EVM. After install prebuilt packge to board sd-card and boot it success to uboot.But when I run ums 0 mmc 0,it will be stuck and serial port has no response.And ctrl+c is useless…
    • Resolved
    • Answered

  • RE: In the sdk 850 version, MCAN16 can work normally on mcu2-1 at j784s4-evm, but it can only send data but not receive data on mcu2-0. Can you tell me what causes it?

    Resolved
    Hi Karan， The current issue has been resolved, as it was due to a configuration problem in my code. Thank you for your attention. Regards Jocc
    • Answered

  • [FAQ] 66AK2E05: How to run the Security Accelerator example on Arm core 0 (ARM_15core#0) on K2E EVM board ?

    Resolved
    Part Number: 66AK2E05 Hi, How to run the Security Accelerator example on Arm core 0 (ARM_15core#0) on K2E EVM board ?
    • Resolved

  • PGA460PSM-EVM: Use registerreaad to read the value of the register and the return value is always 0

    TI Thinks Resolved
    Part Number: PGA460PSM-EVM Other Parts Discussed in Thread: PGA460 , ENERGIA Hi team, One of our customer's issues, I'm forwarding it below, could you please provide some troubleshooting suggestions The communication for the PGA460 is in USART mode…
    • Answered

  • TPS7A49: When the TPS7A49 EVM NR/NSS is grounded, the output voltage is 0

    Resolved
    Part Number: TPS7A49 When the TPS7A49 EVM NR/NSS is grounded, the output voltage is 0. The chip manual explains the Colum to soft-start, so why is it not possible to start if it is grounded？ What's more, when i changed the input vlotage from 7V to 10V…
    • Resolved

  • AWR2944EVM: Unable to flash the EVM with 1-0-1 jumper settings

    TI Thinks Resolved
    Part Number: AWR2944EVM Dear support team, similar to https://e2e.ti.com/support/sensors-group/sensors/f/sensors-forum/1081152/awr2944evm-not-able-to-flash-the-evm I prepared flashing the EVM, but it fails: I have checked the value of the register MSS_CTRL…

  • AM6442: AM64x-evm i2c-0 AT24CM01 problem

    Part Number: AM6442 Other Parts Discussed in Thread: INA226 Dear TI supporters, I have tried to test I2C-0 by the following command: root@am64xx-evm:/# i2cget -y 1 0x40 0 w 0x2741 root@am64xx-evm:/# i2cdetect -l i2c-3 i2c OMAP I2C adapter…

Didn't find what you are looking for? Post a new question.