TI E2E support forums
TI E2E support forums
  • User
  • Site
  • Search
  • User
  • E2E™ design support >
  • Forums
    • Amplifiers
    • Audio
    • Clock & timing
    • Data converters
    • DLP® products
    • Enterprise Automation Integration
    • Interface
    • Isolation
    • Logic
    • Microcontrollers
    • Motor drivers
    • Power management
    • Processors
    • RF & microwave
    • Sensors
    • Site support
    • Switches & multiplexers
    • Tools
    • Wireless connectivity
    • Archived forums
    • Archived groups
  • Technical articles
    • Analog
    • Automotive
    • DLP® technology
    • Embedded processing
    • Industrial
    • Power management
  • TI training
    • Tech days
    • Online training
    • Live events
    • Power Supply Design Seminar
  • Getting started
  • 简体中文
  • More
  • Cancel


Search tips
Showing 202 results View by: Thread Post Sort by
  • DP83TC811R-Q1: How to configure the 100Base-TX Full-Duplex

    Xiaoxiang Liu
    Xiaoxiang Liu
    Part Number: DP83TC811R-Q1 Other Parts Discussed in Thread: DP83TC811 Hi Team, How to configure the 100Base-TX Full-Duplex? I find the 0x0001 is a read-only register. Thanks, Xiaoxiang
    • 2 months ago
    • Interface
    • Interface forum
  • DP83TC811R-Q1: Working at 10Mbps/Half instead of 100Mbps

    Amy Luo
    Amy Luo
    Part Number: DP83TC811R-Q1 Other Parts Discussed in Thread: TDA2 , DP83TC811 Hi team, One of our customer's issues, I'm forwarding it below, could you please provide some troubleshooting suggestions SOC: TDA2 LINUX: 4.19.73 It uses the DP83TC811 driver…
    • 3 months ago
    • Interface
    • Interface forum
  • Answered
  • DP83TC811R-Q1: DP83TC811x-DP83TC812x Link control

    Petar Drnic Matic
    Petar Drnic Matic
    Resolved
    Part Number: DP83TC811R-Q1 When the device is configured, initialized and up and running, in order to set link status to active/down only register 0x485 (PCS_CTRL1) bit 12 should be set/cleared. 1) Is this correct? 2) If this is correct, is such bit/register…
    • Resolved
    • 4 months ago
    • Interface
    • Interface forum
  • DP83TC811R-Q1: Polarity change

    Ekrem Albayrak
    Ekrem Albayrak
    Part Number: DP83TC811R-Q1 Hello, we are using the DP83TC811R-Q1 Low Power Automotive PHY. The Phy has the automatic function to change the polarity if the wires are not correctly connected. We want to know when this happens, which parameter does describe…
    • 6 months ago
    • Interface
    • Interface forum
  • DP83TC811R-Q1: pin FMEA of DP83TC811R-Q1

    Bhabana Baruah
    Bhabana Baruah
    Part Number: DP83TC811R-Q1 Hi , Requesting pin FMEA for mentioned part number. Regards, Bhabana
    • 9 months ago
    • Interface
    • Interface forum
  • DP83TC811R-Q1: test mode4 transmission distortion exceeded expectations

    Amy Luo
    Amy Luo
    Part Number: DP83TC811R-Q1 Hi team, One of our customer's issues, I'm forwarding it below, could you please provide some troubleshooting suggestions The transmission distortion test fail, the values are as shown in the figure below, layout is as…
    • 6 months ago
    • Interface
    • Interface forum
  • DP83TC811R-Q1: Maximum transmission distance

    Kenji Ohno1
    Kenji Ohno1
    Part Number: DP83TC811R-Q1 Hi Team, I would like to know the maximum transmission distance during TI's evaluation. I found that it transmits 40m when using shielded cable. Is there a 100m transmission capability for 100Base-T1? Regards, Kenji
    • 7 months ago
    • Interface
    • Interface forum
  • Answered
  • DP83TC811R-Q1: Does it support RMII repeater mode?

    Matthew Tran
    Matthew Tran
    Resolved
    Part Number: DP83TC811R-Q1 Other Parts Discussed in Thread: DP83TC811 From https://e2e.ti.com/support/interface-group/interface/f/interface-forum/1113891/faq-dp83tc812r-q1-how-can-i-connect-phys-back-to-back-over-rmii , does the DP83TC811R-Q1 also support…
    • Resolved
    • 7 months ago
    • Interface
    • Interface forum
  • RE: DP83TC811R-Q1: SQI and PMA issues

    Cherry Zhou
    Cherry Zhou
    Hi David, David Creger said: Have you seen the following app note: SNLA293 Based on the app note provided, the SQI value is attenuated after noise increase. Will the link status of bit [2] in BMSR Register 0x0001 – Basic Mode Status Register be affected…
    • 7 months ago
    • Interface
    • Interface forum
  • DP83TC811R-Q1: 100BASET to 100BASE-T1 interface with DP83TC811 and DP83826E

    Bo Liss
    Bo Liss
    TI Thinks Resolved
    Part Number: DP83TC811R-Q1 Other Parts Discussed in Thread: DP83TC811EVM , DP83826E , I want to make an interface similar to the DP83TC811EVM between 100BASE-T and 100BASE-T1 but with DP83826E instead of DP83822. The evaluation board uses the RGMII interface…
    • 7 months ago
    • Interface
    • Interface forum
>

Didn't find what you are looking for? Post a new question.

  • Ask a new question
About TI
Company News & events Investor relations Corporate citizenship Careers Contact us
Quick links
TI E2E™ design support forums Customer support center Packaging Quality & reliability TI university program myTI FAQ
Buying
Ordering resources Ordering help & FAQs BOM & cross reference tool Quick add to cart Authorized distributors
Connect with us

Texas Instruments has been making progress possible for decades. We are a global semiconductor company that designs, manufactures, tests and sells analog and embedded processing chips. Our products help our customers efficiently manage power, accurately sense and transmit data and provide the core control or processing in their designs.

Cookie policy Privacy policy Terms of sale Terms of use Trademarks Website feedback

© Copyright 1995-2023 Texas Instruments Incorporated. All rights reserved.