Search tips
Showing 36 results View by: Thread Post Sort by

  • DP83TC811SEVM: Set Up and Technical Inquiry

    Part Number: DP83TC811SEVM Other Parts Discussed in Thread: DP83TC811 Hello E2E Experts, Good day. I want to know something about DP83TC811SEVM. What do I need if I want to use this board? All I know now is that the MSP430 controls the MDIO, and a 100Base…
    • Answered

  • RE: DP83TC811SEVM: RMII Master and Slave Hardware Bootstrap Configurations

    Resolved
    Let me briefly explain our item. For our item, if you deliver the video of the front and rear cameras in the form of an IP camera to DP83TC811R-Q1, A solution that monitors images with IP addresses. The primary design is to complete the IP solution by applying…

  • DP83TC811SEVM: PHY kernel driver of DP83TC811 is activated ( linux/drivers/net/phy/dp83tc811.c )

    Part Number: DP83TC811SEVM Other Parts Discussed in Thread: DP83TC811 I have a question. Currently, when the PHY kernel driver of DP83TC811 is activated, it is recognized as 10Mbps/half and works I'm not doing it. So, without using the PHY kernel driver…
    • Answered

  • DP83TC811SEVM：テストモード変更方法

    Resolved
    Part Number: DP83TC811SEVM Other Parts Discussed in Thread: USB-2-MDIO , DP83TC811 DP83TC811SEVMに搭載されているPHYのテストモード変更方法を詳しく知りたい。 MSP-EXP430G2を所有しています。
    • Resolved
    • Answered

  • DP83TC811SEVM: General Functionality questions

    Resolved
    Part Number: DP83TC811SEVM Other Parts Discussed in Thread: DP83TC811 I want to begin with UTP 1 st , as my link is <10m. Does this device/EVM have a traffic generator or at least a PRBS coder and encoder (PRBS 9/11, etc.)? BER counter? Package loss…
    • Resolved
    • Answered

  • DP83TC811SEVM: Setup of EVM

    Resolved
    Part Number: DP83TC811SEVM Other Parts Discussed in Thread: MSP430F5529 Hi team, Which MSP430 launchpad need to be used with DP83TC811SEVM? Any software/firmware guide for DP83TC811SEVM?
    • Resolved
    • Answered

  • DP83TC811SEVM: Can't get DP83822EVM TX to work with DP83TC811SEVM T1

    Resolved
    Part Number: DP83TC811SEVM Hi support, Pull low and pull high resistor is different between these two evaluation boards on MII/RMII interface. Which is the correct setup to get these two boards communicating? Thanks, Stanley
    • Resolved

  • Linux/DP83TC811SEVM: DP83TC811SEVM's communication issue

    Answer Suggested
    Part Number: DP83TC811SEVM Other Parts Discussed in Thread: DP83TC811 Tool/software: Linux Hi team, I am the FAE in Guangzhou, now the customer Gosuncn is evaluating the DP83TC811S using DP83TC811SEVM. The customer’s situation is shown below: …

  • DP83TC811SEVM: DP83TC811SEVM's application and communication issue

    TI Thinks Resolved
    Part Number: DP83TC811SEVM Other Parts Discussed in Thread: MSP430F5529 , DP83TC811 Hi Team, I'm doing a little project to understand the communication via automotive Ethernet PHY DP83TC811S and evaluate the DP83TC811S using DP83TC811SEVMs. About these…

  • DP83TC811SEVM: Status register 0x01 -> Device not able to perform Full-Duplex 100Base-TX, Half-Duplex 100Base-TX, Full-Duplex 10Base-T, Half-Duplex 10Base-T

    TI Thinks Resolved
    Part Number: DP83TC811SEVM Other Parts Discussed in Thread: DP83TC811 Hi, I use a DP83TC811SEVM evaluation board connected over RGMII to my i.MX6 main board. I established the MDIO communication sucessfully. I can read and write registers over MDIO. …

Didn't find what you are looking for? Post a new question.