• DS100BR111A: Redriver supporting 1000BASE-T

  

  Atsushi Takahashi

  TI Thinks Resolved

  Part Number: DS100BR111A Other Parts Discussed in Thread: DS100MB203 , Tool/software: Hi Team, My customer is running 1000BASE-T over a 1.5m cable, but is experiencing signal degradation and is looking for a redriver. Based on the following threads…

  • 4 months ago
  • Interface
  • Interface forum
Answered

• DS100BR111A: Redriver for DP83826E

  

  Dimitar Yolovski

  Resolved

  Part Number: DS100BR111A Other Parts Discussed in Thread: DP83826E , Tool/software: Dear Colleagues, The customer needs an Ethernet redriver placed between the DP83826E and an MDI interface. Is it possible to use DS100BR111A for this application,…

  • Resolved

  • 11 months ago
  • Interface
  • Interface forum
Answered

• DS100BR111A: Will the DS100BR111A meet the requirements?

  

  Charlie Xiao

  Resolved

  Part Number: DS100BR111A Other Parts Discussed in Thread: DS110DF111 , DS100BR111 Hi Team, Will the DS100BR111A meet the requirements? The main requirements are as follows: Single-channel (TX\RX each pair of differential lines) bidirectional,…

  • Resolved

  • over 3 years ago
  • Interface
  • Interface forum
Answered

• DS100BR111A: Works at 10.3125Gbps?

  

  Kazuhiko Hirano

  Resolved

  Part Number: DS100BR111A Other Parts Discussed in Thread: DS100BR210 , DS100BR111 Hello, My customer is looking for 2ch Redriver or Retimer working at 10.3125Gbps. DS100BR111A datasheet says that DS100BR111A, DS100BR210 and DS100BR111 are “Two Channel…

  • Resolved

  • over 2 years ago
  • Interface
  • Interface forum

• DS100BR111A: Principle of signal transmission

  

  Charlie Xiao

  TI Thinks Resolved

  Part Number: DS100BR111A Hi Team, Does the chip reconstruct the signal and send it out, or does it amplify the signal and send it out? Thanks. Regards, Charlie

  • over 2 years ago
  • Interface
  • Interface forum
Answered

• DS100BR111A: EQA1 EQB1

  

  Charlie Xiao

  Resolved

  Part Number: DS100BR111A Other Parts Discussed in Thread: DS100BR111 Hi Team, For DS100BR111A, In pin mode, must the pull-up and pull-down states of EQA1 and EQB1 be the same? In addition, when debugging EQ and DEM, what is the recommended direction…

  • Resolved

  • over 3 years ago
  • Interface
  • Interface forum

• DS100BR111A: does DS100BR111A support 1000M Ethernet PHY?

  

  Max Han

  TI Thinks Resolved

  Part Number: DS100BR111A Hi , does DS100BR111A support Gigabit (1000M) Ethernet PHY?

  • over 8 years ago
  • Interface
  • Interface forum

• DS100BR111A: 6G 4w mil SAS/SATA solution

  

  Frank Xiao

  TI Thinks Resolved

  Part Number: DS100BR111A Hi team, My customer has a new requirement below. 1. can support 6G SAS/ SATA 2. can support 40,000 mil length and can be put in the middle of the length.(20,000mil length point) Could you please help check the solution…

  • over 6 years ago
  • Interface
  • Interface forum

• DS100BR111A: 1000Base-KX redriver

  

  Peter Chen(ICP_FAE)

  TI Thinks Resolved

  Part Number: DS100BR111A Other Parts Discussed in Thread: DS25BR110 is the DS100BR111A right supporting 1000Base-KX redriver? if not, is there any redriver/retime suggest?

  • over 7 years ago
  • Interface
  • Interface forum
Answered

• DS100BR111: DS100BR111,DS100BR111A Difference and Threshold Level

  

  Hiroaki Yuyama TED

  Resolved

  Part Number: DS100BR111 Dear, support team. What is the difference between DS100BR111 and DS100BR111A? Do you have a min value for the Assert and De-assert Level? We are considering replacing from Pericom Semiconductor ReDriver. Best Regards, Hiroaki…

  • Resolved

  • over 7 years ago
  • Interface
  • Interface forum

Didn't find what you are looking for? Post a new question.