Answered

• DS110DF1610: What is the E suffix meaning in the ordering code

  

  Ido Sasson

  Resolved

  Part Number: DS110DF1610 Hi, I would like to check what is the actual diffrence between the following 2 part numbers (E and without E). Are they both eactly the same compoenent 1:1 ? DS110DF1610FB/NOPB DS110DF1610FBE/NOPB Thank you. Ido

  • Resolved

  • 1 month ago
  • Interface
  • Interface forum

• DS110DF1610: Does CDR reset temporarily block incoming signals

  

  Kyle MacNeil

  Part Number: DS110DF1610 Hello, We are using the DS110DF1610 retimer device in our networking system and have a question regarding the "Cross Point Switch" process in section 6.3.1.3 of the datasheet (shown below) . We understand that the reitmer offers…

  • 5 months ago
  • Interface
  • Interface forum

• DS110DF1610: CDR Lock challenge depending on MUX config

  

  David Brule

  TI Thinks Resolved

  Part Number: DS110DF1610 Tool/software: Hi, We are having difficulty achieving CDR lock in the following condition We are using the SigCon Architect tool to configure the device and we have a signal input into RX0B When we have TX0B looking at RX0B…

  • over 1 year ago
  • Interface
  • Interface forum

• DS110DF1610: How to configure and use DS110DF1610

  

  lucy.zhang

  TI Thinks Resolved

  Part Number: DS110DF1610 Other Parts Discussed in Thread: DS125DF1610 Hello TI, 1. Is there a register configuration case for DS110DF1610? Yes, please provide. If not, please provide configuration guidance. 2. How does DS110DF1610 register configuration…

  • over 3 years ago
  • Interface
  • Interface forum

• DS110DF1610: about using SigCon architect software to debug DS110DF1610

  

  lucy.zhang

  TI Thinks Resolved

  Part Number: DS110DF1610 Other Parts Discussed in Thread: DS250DF410 Hello TI, Questions about using SigCon architect software to debug DS110DF1610: When manually adjusting parameters for RX EQ/DFE, what is the meaning of these values and how to…

  • over 3 years ago
  • Interface
  • Interface forum
Answered

• DS110DF1610: Ethernet switch

  

  Shuji Ishiwata

  Resolved

  Part Number: DS110DF1610 Hi All, I have a question about ethernet products. Do you have ethernet switch products? If you have a product, we are looking for an Ethernet switch with the following specifications. -GMII or RGMII - With VLAN - Minimum…

  • Resolved

  • over 2 years ago
  • Interface
  • Interface forum

• DS110DF1610: Determining which Divider Group settings (0 or 1) actually achieved CDR Lock?

  

  David Brule

  TI Thinks Resolved

  Part Number: DS110DF1610 Tool/software: If group 0 is set to 8.5Gpbs and Group 1 is set to 10.0Gbps, can you determine which group actually achieved CDR lock by reading registers? Can the locked sub-rate be determined?

  • over 1 year ago
  • Interface
  • Interface forum

• DS110DF1610: CH REG 0x02 MULTI_PURP_STATUS(7:0) and 0x0C STATUS_CONTROL(7:4) details?

  

  David Brule

  TI Thinks Resolved

  Part Number: DS110DF1610 Other Parts Discussed in Thread: DS250DF230 , DS110DF410 Tool/software: Hello, I'm trying to troubleshoot a confusing CDR lock inconsistency and I read in another thread " DS250DF230: CDR lock is not stable" that the bits in…

  • over 1 year ago
  • Interface
  • Interface forum

• DS110DF1610: DS110DF1610FBE/NOPB

  

  Chen Bing

  Part Number: DS110DF1610 Hello, We enconter a problem when we use DS110DF1610: 1. The test rate is 10.3125G, the swing of the optical module on BERT is 850mV 2. We configurured the Card with DS110DF1610, and the rate is 10.3125G and everything works…

  • over 2 years ago
  • Interface
  • Interface forum

• DS110DF1610: Need the Programming Guide

  

  liang wang

  TI Thinks Resolved

  Part Number: DS110DF1610 Hi I am using DS110DF1610 for my design. can someone send programming guide to me? my email is liang.wang@accelecom.com . Thank you.

  • over 3 years ago
  • Interface
  • Interface forum

Didn't find what you are looking for? Post a new question.