Answered

• DS125DF111EVM: Evaluation Board GUI

  

  José R. Quintanillla

  Resolved

  Part Number: DS125DF111EVM I have a DS125DF111EVM and the O.S. of my computer is Windows 10. What Evaluation Board Software must I use?. I have tried to install snlc055e but it doesn't work.

  • Resolved

  • over 1 year ago
  • Interface
  • Interface forum

• DS125DF111EVM: About DS125DF111EVM Channels

  

  Bear L

  TI Thinks Resolved

  Part Number: DS125DF111EVM Hi I have an other question. 1. I configure the channel in the same way,Channel A is worked,Why the Channel B is not Work?? 2. Can Channel A/B work at the same time and work at different frequencies? Regards,

  • over 6 years ago
  • Interface
  • Interface forum

• DS125DF111EVM: No singal detected on Channel A

  

  Jue Wang

  TI Thinks Resolved

  Part Number: DS125DF111EVM Hi, there Can I ask a question regarding the DS125DF111EVM: when 10Gbps Vpp=100mV data input was on channel B, everything works great, however when I just switch the input from channel B to channel A, no signal detected and…

  • over 4 years ago
  • Interface
  • Interface forum

• DS125DF111EVM: problem when using GUI

  

  Cindy Chang

  TI Thinks Resolved

  Part Number: DS125DF111EVM Other Parts Discussed in Thread: DS125DF111 Hi , We have some problem when using GUI for DS125DF111. We were trying to change the config setting under SMBus slave mode with SigCon Architect, however the channel indicator…

  • over 4 years ago
  • Interface
  • Interface forum
Answered

• DS125DF111EVM: 3G-SDI or even 12G-SDI

  

  Jue Wang

  Resolved

  Part Number: DS125DF111EVM Other Parts Discussed in Thread: DS125DF111 Hi, there I am wonderring if DS125DF111EVM could lock and recovery 3G-SDI or even 12G-SDI signal? From data sheet, it reads that DS125DF111 could lock from 9.8 to 12.5Gbps and…

  • Resolved

  • over 4 years ago
  • Interface
  • Interface forum

• DS125DF111EVM: high current and no signal detected

  

  Jue Wang

  TI Thinks Resolved

  Part Number: DS125DF111EVM Other Parts Discussed in Thread: DPS-DONGLE-EVM , DS125DF111 Hi, there I got new purchased DS125DF111EVM board and the initial set up is as shown below It was set as SMBus slave mode connected with DPS-DONGLE-EVM. The…

  • over 4 years ago
  • Interface
  • Interface forum
Answered

• DS125DF111EVM: DS125DF111EVM and USB2ANY

  

  randall blair

  Resolved

  Part Number: DS125DF111EVM Other Parts Discussed in Thread: USB2ANY , My experience is exactly the same as this thread, but I still can't connect to the EVM (invalid address). I have tried with jumpers just as in the EVM guide setup photo and with ADDR0…

  • Resolved

  • over 7 years ago
  • Interface
  • Interface forum

• RE: DS125DF111EVM: How can make the DS125DF111EVM work normally in Pin Control Mode?

  

  Harrison Wang

  The currentdrawn by the 3.3V power supply is about 100~150mA. The signal source is PRBS31 and the data rate is 10.3125G. The LOCK LED don't light green. We Try to connect A&B channel with the signal source,but the EVM still have no output signal…

  • over 6 years ago
  • Interface
  • Interface forum

• DS125DF111EVM: Board Dimensions and Mounting Hole Locations

  

  Charles Harris

  TI Thinks Resolved

  Part Number: DS125DF111EVM What are the Board Dimensions and mounting hole sizes and locations for the DS125DF111EVM board?

  • over 5 years ago
  • Interface
  • Interface forum

• DS125DF111EVM: How to write to EEPROM with dumped config file under EEPROM mode ?

  

  Cooper (Wei) Lo

  TI Thinks Resolved

  Part Number: DS125DF111EVM Other Parts Discussed in Thread: DS125DF111 Hello, My situation is I have a config file dumped from SMBus slave mode, for now I'm trying to verify this config file can be read and written to the EEPROM while using SigCon Tool…

  • over 4 years ago
  • Interface
  • Interface forum

Didn't find what you are looking for? Post a new question.