Search tips
Showing 39 results View by: Thread Post Sort by

  • DS90CR285: DS90CR285 sampling point

    Part Number: DS90CR285 Other Parts Discussed in Thread: DS90CR286 , Tool/software: In the datasheet for the channel link IC device "DS90CR285, DS90CR286," the RSPos* for f=66MHz is listed in the red frame in the receiver switching characteristics below…
    • Answered

  • DS90CR285: about Transmitter Switching Characteristics and Receiver Switching Characteristics

    Resolved
    Part Number: DS90CR285 Tool/software: Hi all, I have some questions about the following data sheet. DS90CR285/DS90CR286 3.3V Rising Edge Data Strobe LVDS 28Bit Channel Link- 66MHz datasheet (Rev. C) (1)At f=66.6666 MHz TPPos0,TPPos1,TPPos2,TPPos3…
    • Resolved

  • DS90CR285: DS90CR285, DS90CR286

    TI Thinks Resolved
    Part Number: DS90CR285 Other Parts Discussed in Thread: DS90CR286 , Hi, I am in need of cost effective P2P alternate for DS90CR285, DS90CR286 , so kindly suggest at the earliest

  • SN75LVDS82: SN75LVDS82 1V8 alternative to DS90CR285

    Part Number: SN75LVDS82 Other Parts Discussed in Thread: DS90CR285 , , SN65LVDS93 HI I have a board with a channel link receiver DS90CR285 , which is 3V3 interface for FPGA. I need to use 1V8 FPGA banks. Can I use SN75LVDS82 (FlatLink) as 1V8…
    • Answered

  • DS90CR286A: maximum cable length w/ error free at DS90CR285 to DS90CR286A

    Resolved
    Part Number: DS90CR286A Other Parts Discussed in Thread: DS90CR285 , Hello, My customer would like to transmit and receive 462Mbps data with 66MHz shift clock using DS90CR285 and DS90CR286A. At this data rate, up to how much meters 3M MDR cable can users…
    • Resolved

  • DS90CR285: About DS90CR285 clock interference

    Part Number: DS90CR285 Hi Team, The customer is experiencing below issue and needs your help. system structure: After the analog video signal was adjusted and amplified by the op amp, it entered the ADC for analog-to-digital conversion. After the…
    • Answered

  • DS90CR285: DS90CR285

    Resolved
    Part Number: DS90CR285 Hi, i AM USING DS90CR285 IN MY PROJECT, in single "TCIP" period Falling edge we need to load 28 bit data (or) we should use 28 TCIP clock period Falling edge to load 28 bits data (1bit / TCIP clock period). kindly confirm…
    • Resolved
    • Answered

  • DS90CR285: LVCMOS Pin Connection

    Resolved
    Part Number: DS90CR285 Other Parts Discussed in Thread: DS90CR286 Dear Teams, My customer is asking how to connect the data to the pin if they have a 8 bits LVCMOS data input for DS90CR285? Also, what is the order or sequence they need to connect for…
    • Resolved

  • DS90CR285: Camera link + 85MHz clock + -40 degree device recommendation

    TI Thinks Resolved
    Part Number: DS90CR285 Hi team Do we have devices that could meet these specs? Specs: Camera link 85MHz clock input 28bits width bus Support -40° LVDS to LVCMOS, LVCMOS to LVDS In Channel Link Products Selection Guide( https://www…
    • Answered

  • DS90CR286A: DS90CR285 unused pin

    Resolved
    Part Number: DS90CR286A Hi I have a question about treatments of unused pin "RxIN3+/-". Should I connect a pull-down register? Do you have recommendation value? thanks,
    • Resolved

Didn't find what you are looking for? Post a new question.